Charge both your starter battery and leisure battery at once from 1 solar panel. Made by EPsolar who make our popular Tracer MPPTs.
Please note, if running a long cable to one of your batteries please ensure you use a thick enough cable. Please use this volt drop caclulator to see your losses on the cable you plan to use.
·Two battery charging eliminates the extra cost of two separate solar charging system
·Intelligent System Optimum Control
·12/24V auto work
·Battery type selection
·Charging frequency optional
·High efficient Series PWM charging
·Local external temperature compensation
·Remote temperature sensor optional
·Use MOSFET as electronic switch, without any mechanical switch
·Remote meter MT-1 optional
·Electronic protection: over charging, short circuit, battery reverse polarity protection
Electrical parameters |
|
System voltage |
12 / 24VDC Auto work |
Nominal battery current |
10A,20A |
Charge circuit voltage drop |
≤0.26V |
Discharge circuit voltage drop |
≤0.15V |
Self consumption |
≤6mA |
Working temperature |
-35℃ to +55℃ |
Humidity |
10%-90% NC |
Enclosure |
IP30 |
Terminal |
4mm2 |
Net weight |
0.24kg |
Battery voltage parameters (temperature at 25°C) |
|||
Battery charging setting |
Sealed |
Flooded |
Gel |
Equalize charging voltage |
14.4 V;x2/24V |
14.6V;x2/24V |
14.8V;x2/24V |
Boost charging voltage |
14.2V;x2/24V |
14.4V;x2/24V |
14.6V;x2/24V |
Float charging voltage |
13.7V;x2/24V |
13.7V;x2/24V |
13.7V;x2/24V |
Max. solar voltage |
30V(12V system),55V(24V system) |
||
Battery voltage range |
8-15V(12V system),8-30V(24V system) |
||
Self-consumption |
4mA at night, 10mA at charging |
||
Meterbus connection |
8-pin RJ-45 |
||
Temp. compensation |
-5mv/℃/2V |
• Low voltage-temperature coefficient enhances high temperature operation.
• Exceptional low light performance and high sensitivity to light across the entire solar spectrum.
• 25 - Year limited warranty on power output and performance.
• 5 - Year Limited warranty on materials and workmanship.
• Sealed, waterproof, multi-functional junction box gives high level of safety.
• High performance bypass diodes minimise the power drop caused by shade.
• Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation.
• A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems.
• Highest quality, high transmission tempered glass provides enhanced stiffness and impact resistance.
• Please note unusually these panels do not come with any cable or connectors. You might like to consider 6mm square solar cable and MC4 connectors.
Fixes without screwing holes in your roof!
ABS mounts raise the panel by 25mm. Edge of panel to edge of ABS is 55mm.
We sell CT1 which is great for sticking these down, please see related products tab for different colours avaialble.
If you are fitting to a vehicle we recommend that you additionally bolt or screw the panel and mounting down as well, as the strength of these systems is only as strong as the roof type or paint on your roof!
NOTE - You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method...
Here is a good tutorial to get you started:
6mm² Solar Cable - Price is per meter, simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit. If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.
This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.
You will also need suitable cable entry glands - please see related products tab.
Product Depth | 114 mm |
Product Height | 160 mm |
Product Type | DIN Enclosure |
Product Width | 85 mm |
For use with our stick down panels and ABS mounting kits - also great for sealing cable holes
CT1 will successfully bond:
Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals
Application
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)
Drying Time
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.
Cable Gland Entry Box, use to connect through external surface. Perfect for solar panel cables coming from outside to controller.
This comes with a cradle for keeping your MC4 connectors in place and tidy.
Dimensions:
Length 182mm
Width 95mm
A small, low cost multimeter supplied with test leads and holster.
DMM Functions: DC Current, AC/DC Voltage, Continuity, Diode, Resistance, Transistor
No. of Digits: 3.5
DMM Response Type: Average
Display Count: 1999
Range Selection: Manual
Voltage Measure DC Max: 500V
Voltage Measure AC Max: 500V
Current Measure DC Max: 5A
Resistance Measure Max: 2Mohm