This is a complete 100Kw PV generation kit with 63Kw AC output to be configured as 3 Phase with 21Kw per phase. It has 8400Ah of NiFe batteries which is around 680Kwhrs of storage (at a C100 rate).
Invented over 100 years ago by Thomas Edison as a non-polluting and non-consumable alternative to Lead Acid Batteries using no heavy metals! Now manufactured once again worldwide after lead acid battery companies closed Edison's Plant in 1972.
We have sourced NiFe at a competative rate at a little over double our cheap lead acid range and similar to our Rolls battery prices. This makes them a very viable option for long term off grid solutions.
You need 10 cells to make up a 12V bank, 20 cells for a 24V bank and 40 cells for a 48V bank
They have low operation cost, low self-discharge, long cycling life and environmental-friendly. They can withstand deep discharge, wide temperature variations, mechanical & electrical abuses and still show excellent and reliable performance over a long period. The operation life of solar Ni-Fe batteries is 30-40 Years, the working temperature range can be -40°C to 60°C, which is also the longest life battery for the PV system.
|Model||Nominal Voltage (V)||Rate Capacity (AH)||MAX. Dimension(mm)||Dry weight (kg)||Wet weight (kg)||Terminal||Container Material|
These have a long lead time as they are made to order and shipped over to us, please allow 2 months for delivery, but for a battery that will out live any other battery if your deciding to go down this route its definitely worth the wait and this is the reason we can keep the prices low.
These Panels are in high demand - Current Stocks are 300W
If you would prefer 305W these are due in Mid April - Please email us after ordering if you want to wait for 305W rather than have 300W
305W JA Solar Panels Mono Percium - All Black
The latest in mono cell technology with passivated backside, local BSF and 4 Bus Bars from worldwide PV Cell leaders - JA Solar
First to reach >20.6% average cell efficiency in mass production
More Power Per m²
JA higher efficiency module type specially designed for UK rooftop market.
Maximise the kWp installation on the roof
Homogeneous Black Mono cells.
Black Frame for anti-glare and pleasing appearance.
Lower System Cost
Reduced installation and BOS cost
Excellent Low-light Performance
Enhanced spectral response at longer wavelength boosts low-light performance, which can produce more than 1% additional power compared with conventional module at system side.
Passed "3xMCS" TÜV SÜD Thresher Long life Accelerated Stress Tests.
Full range of PID-resistance tests
Harsh climate environment endurance tests
Full set of long-term reliability tests
Manufacturing inspected and certified by leading institutes such as PI-Berlin, Franhoeffer, Sgurr, OST and Solar-IF
100% in-house automatic manufacturing
2X 100% EL inspection ensuring defect-free production
Over 500MWp of JA Solar panels installed in the UK. 10GWp Worldwide.
Positive power tolerance: -0~+5W
Modules binned by current to improve system performance
Excellent mechanical load resistance: Certified to withstand high wind loads (2400Pa) and snow loads (5400Pa)
Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel.
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
Get upto 5% discount with automatically applied payment discounts in the checkout.
Delivery from £24+vat
First panel £24+vat, each additional panel just £6+vat delivery
ie: 3 panels costs £36+vat delivery.
Delivery service is an economy service that hand delivers fragile items on a weekly round across the UK.
Surcharge for remote areas including parts of Wales, Scotland, Ireland and Isle of Wight, please see Delivery info
This is a safer more reliable and cheaper way for you to receive panels and saves on the huge amounts of wasted packing materials.
Pallet Shipping 30 panels per pallet:
£150 UK Mainland
£350 Rest of Europe
Or you can collect for FREE from Nr Brighton.
Panel dimensions:1650mm x 991mm x 35mm
The Radian Series GS7048E Grid/Hybrid™ (full-flexibility grid-interactive/off-grid) Inverter/Charger is engineered toward one goal: making system design and installation easier and faster in grid-interactive and comprehensive off-grid applications. The Radian Series simplifies the configuration, distribution, and implementation of energy storage through a standardized approach when integrated with an OutBack GS Load Center, making it easier than ever to provide successful solutions for virtually any residential, commercial or institutional power requirement.
The all-new 230V 50Hz Radian reflects OutBack’s ongoing commitment to clean, reliable power for homes, businesses and other facilities around the world, delivering 7,000 Watts. This model combines pure sine wave power output technology with unsurpassed surge capability to start the most demanding appliances, and are built around a unique dual-power module design which ensures high efficiency in both low and full power operation as well as redundancy in mission-critical applications.
The Radian Grid/Hybrid inverter incorporates OutBack’s FLEXgrid™ technology for full operational flexibility. Modular system architecture and simplified parallel design supports three-phase systems up to 21kW and multiple inverter arrays of up to 70kW. System integration and programming are easy with OutBack’s powerful MATE3 Control and HUB Communications Management devices. An advanced, front-vented layout provides optimum cooling in zero-clearance installations (i.e. where units are stacked next to each other). Field-serviceable design simplifies maintenance if needed, and firmware updates can be easily made in the field without specialized equipment.
|Nominal DC Input Voltage||48 VDC|
|Continuous Output Power at 25 °C||7000 VA|
|AC Output Voltage||230 VAC (212-250 VAC)|
|AC Output Frequency||50 or 60 Hz|
|Continuous AC Output Current at 25 °C||30 AAC|
|Continuous AC output Current at 25° C||30 AAC|
|Idle Consumption - Invert mode, no load||34 Watts|
|CEC Weighted Efficiency||N/A|
|Total Harmonic Distortion (Typical)||><5% THD, Max single voltage harmonic <2%|
|Output Voltage Regulation||± 2%|
|Maximum Output Current (1 ms peak)||100 AAC|
|Maximum Output Current (100 ms RMS)||70.7 AAC|
|Overload Capability (100 ms surge)||16.3 kVA|
|Overload Capability (5 second)||11.5 kVa|
|Overload Capability (30 minute)||7.9 kVa|
|AC Input Voltage Range (Adjustable)||170 to 290 VAC|
|AC Input Frequency Range||45 to 55Hz or 55 to 65Hz|
|Grid-Interactive Voltage Range||208 to 252VAC (EN50438)|
|Grid-Interactive Frequency Range (Default)||57Hz to 61Hz (EN50438)|
|AC Input Current (Maximum)||50 AAC|
|Continuous Battery Charge Output||100 ADC|
|DC Input Voltage Range||40 - 64 VDC|
|Temperature Range (rated)||0°C to 50°C (power derated above 25°C)|
|Temperature Range (maximum)||
-40°C to 60°C (functions, but does not necessarily meet all component specifications)
|Accessory Ports||Remote Temperature Sensor and MATE3/HUB Communications|
|Field Upgradable Firmware||Yes|
|Certifications||IEC 62477-1, AS4777.2, AS4777.3, EN61000-6-1, EN61000-6-3, EN61000-3-2, EN61000-3-3, AS3100, CE, RoHS compliant per directive 2011/65/EU|
|Warranty||Standard 5 Year|
|Unit Weight||125 lbs (56.7 kg)|
|Shipping Weight||140 lbs (63.5 kg)|
|Inverter Dimensions (H x W x D)||28 x 16 x 8.7" (71.1 x 40.6 x 22.2 cm)|
|Shipping Dimensions (H x W x D)||14.5 x 34.5 x 21" (36.8 x 87.6 x 53.3 cm)|
These are the best charge controllers on the market, they are solid, reliable and what we use for The Bimble Inn.
The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Technologies. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30% compared to non-MPPT controllers. Thanks to active cooling and intelligent thermal management cooling, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 104°F (40°C).
Included in all of the FLEXmax Charge Controllers are the revolutionary features first developed by OutBack Power, including support for a wide range of nominal battery voltages and the ability to step-down a higher voltage solar array to recharge a lower voltage battery bank. A built-in, backlit 80 character display shows the current status and logged system performance data for the last 128 days at the touch of a button. The integrated OutBack network communications allows FLEXmax series Charge Controllers to be remotely programmed and monitored via a MATE system display and provides unrivaled complete system integration.
FLEXmax MPPT Charge Controllers are the only choice when you demand a high performance, efficient and versatile charge controller for your advanced power system.
|Voltage||Recommended PV Max||Absolute Max|
|FLEXmax 80 Specifications|
|Nominal Battery Voltages||12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up)|
|Maximum Output Current||80 amps @ 104° F (40°C) with adjustable current limit|
|Maximum Solar Array STC Nameplate||12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC systems 6250 Watts|
|NEC Recommended Solar Array STC Nameplate||12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts|
|PV Open Circuit Voltage (VOC)||150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum|
|Standby Power Consumption||Less than 1 Watt typical|
|Power Conversion Efficiency||97.5% @ 80 Amps in a 48 VDC System - Typical|
|Charging Regulation||Five Stages: Bulk, Absorption, Float, Silent and Equalization|
|Voltage Regulation Set points||10 to 80 VDC user adjustable with password protection|
|Equalization Charging||Programmable Voltage Setpoint and Duration - Automatic Termination when completed|
|Battery Temperature Compensation||Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell|
|Voltage Step-Down Capability||Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input|
|Programmable Auxilary Control Output||12 VDC output signal which can be programmed for different control applications
(Maximum of 0.2 amps DC)
|Status Display||3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total|
|Remote Display and Controller||Optional Mate or Mate2 with RS232 Serial Communications Port|
|Network Cabeling||Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires)|
|Data Logging||Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production|
|Hydro Turbine Applications||Consult factory for approved Turbines|
|Positive Ground Applications||Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications)|
|Operating Temperature Range||Minimum -40° to maximum 60° C
(Power capacity of the controller is automatically derated when operated above 40° C)
|Environmental Rating||Indoor Type 1|
|Conduit Knockouts||One 1" (35mm)on the back; One 1" (35mm) on the left side; Two 1" (35mm) on the bottom|
|Warranty||Standard 5 year / Available 10 Year|
|Weight - Unit||12.20 lbs (5.56 kg)|
|- Shipping||15.75 lbs (7.10 kg)|
|Dimensions - Unit||16.25" x 5.75" x 4" (41.3 x 14 x 10 cm) -
(H x W x D)
|- Shipping||21" x 10.5" x 9.75" (53 x 27 x 25 cm)|
|Options||Remote Temperature Sensor (RTS), HUB 4,
HUB 10, MATE, MATE 2
|Menu Languages||English & Spanish|
The OutBack Power FLEXware PV combiner series sets the standard for PV balance-of-system hardware. The FLEXware PV8 and FLEXware PV12 accommodate the overcurrent protection requirements of your application. From 150VDC breakers for low voltage PV systems, to 600VDC fuse holders for high voltage PV systems, the FLEXware PV Combiner series handles it all.
Combiner series is designed to survive outdoor environments. Its rainproof, UL type 3R powder coated aluminum chassis can be mounted on a wall, sloped roof or pole. The unique angled negative terminal bus bar design makes wiring fast and easy without the larger output conductors blocking access to the smaller input terminals. Dual output lug terminals are included for up to 2/0 AWG conductors.
The new MATE3 System Display and Controller makes it easy to program and monitor a complete OutBack Power System. An intuitive and integrated system configuration wizard makes system setup and programming quick and seamless.
The ability to set unique multi-level user passwords allows the user to secure critical system settings from unintended changes, while still allowing open access to necessary functions.
The MATE3 is packed full of features to make system management simple. The easy-to-read graphical LCD display is backlit for dark operating conditions. Improved tactile buttons and a user programmable “favorite” key give you immediate access to the features you want, while an intuitive scroll wheel interface allows for easy adjustment of system setpoints. Expandable SD card memory allows you to increase data logging capacity as well as upgrade units in the field.
A built-in clock and calendar function enables timer-based programming of inverter and charger operation. All of your settings are stored in permanent memory to eliminate the need to reprogram in the event of a system shutdown or battery replacement. The MATE3 is an Internet enabled device – simply connecting to the Internet will allow full remote system.
By adding the Mate Controller you can also use the outback inverters as a off grid/grid hybrid system allowing you to use the power from your batteries primarily and switching to use the grid when your batteries are low, thus minimising your use of the grid and ensuring you get the best use of your renewable power set-up, and yet never run out of power. Or you can configure an automatic generator start from them if needed.
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
6mm Solar Cable - Price is per meter simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable
Max load: 50A
16mm cable - for Large Charge Controller to Batteries - 2 Meter leght with M10 Lug
You will need 2 cables per charge controler (Pos & Neg). The Lugs are on 1 end only as the charge controllers have bare wire connectors.
If you need longer lengths please let us know
The HUB-10 communication manager allows the MATE to control and monitor a maximum of ten OutBack products. The inverter/chargers can be operated in a stacked or independent configuration, and OutBack MPPT charge controllers can also be used on any of the ten available ports of the HUB-10. Future OutBack products will also be compatible with the HUB-10. The HUB-10 manages both the inter-inverter communications and the MATE-inverter communication. The HUB-10 also can be used with the X-240 autotransformer when series stacked to allow full surge and continuous AC load capacity of each FX to be available on either of the 120 VAC output circuits. When two or more FX inverters are stacked in a parallel or series configuration, the system automatically turns off any excess slave inverters to save power and maximize conversion efficiency. This power save system is fully automatic and works with or without the MATE connected to the system One or two MATE system controllers and displays can be connected to the HUB. One Mate is allowed to program the systems while the other MATE is able to only control and display the system operation. When using a single MATE with a HUB-10, programming can be locked out by moving the MATE from the 1st MATE port to the 2nd MATE port once programming has been completed. The maximum distance from the HUB-10 to the power conversion product should be under 10 feet. OutBack includes two 3 foot long and two 6 foot long CAT5 cables standard with the HUB-10. Check with your OutBack dealer for additional cables.
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
50mm Cable - Use for connecting Batteries to Inverter M8 - M10 (M8 one end M10 on the other end)
You will need 2 cables, 1 for Positive and 1 for Negative
If you need a longer cable please let us know.
MC4 Solar Connector - Price is per MC4 pair simply select the quantity as the number of MC4 pairs you want.
These are the standard connectors used on most solar panels.
TUV certified, brand new, water /weather proof rubber seal that can ensure excellent electrical contact for life time service.
The metal pin is made from high quality machined copper and sealed tip (compare to the cheap sheet metal pin) that can ensure excellent electrical contact for life time service.
Build in press tabs for easy disconnect, no tool is needed. 25A max load.
Wires should be crimped or soldered into the pins and care should be taken to get the correct pin into the correct connector. Once the pin is pushed into the connector it is difficult to remove without the correct tooling.
MC4 Main Technical Specification:
Maximum Current: 25A
Maximum voltage: 1000V
Maximum operating humidity: 5% -95% (No condensation)
Temperature: -40 ℃ ~ +90 ℃
Waterproof Grade: IP67
Flame class: UL94-V0
Connecting cable specifications: 2.5mm2 4mm2 6mm2
Test voltage: 6.6KV (50Hz, 1min)
Metal materials: nickel copper
Insulation material: PA12 * 1988HB
Lock mode: Self-locking
Security Level: Class ‖
Shell has a strong anti-aging, anti- UV capability; found in outdoor use under harsh environment requirements; according to different needs can be arbitrary and used in conjunction with a variety of cell junction box; all connections are using press-fit connection;
The OutBack Remote Temperature Sensor (RTS) is essential for proper battery charging. All OutBack Power products with integrated battery charging have temperature compensation systems built in which benefit from the installation of the RTS (included with inverter/chargers). With the RTS you can make sure that your OutBack Power System knows the precise battery temperature, so it can recharge your batteries safely and efficiently. If your system has multiple OutBack products connected to one HUB4 or HUB10, only a single RTS needs to be installed.
This industrial quality Multi-Contact tool is a first priority for Crimping MC4 male and female solar contacts, used for the cable(2.5/4/6 mm2)
The excellent handling, easy exchange of the crimping insert bits and the possibility of adding a positioning aid are facts in favour of these crimping pliers.