Bimble Solar 100W Mono Panel
100W power, great for smaller applications and lighting. These are 12V panels so you can use with PWM controllers to make a very cheap system.
Size: 925 x 670 x 30 mm
MC4 ended premade solar cables are 60cm long each
As these are small panels we use standard couriers - delivery is cheaper.
Or you can collect for FREE from Near Brighton, East Sussex
A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.
MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.
Fixes without screwing holes in your roof!
Set of seven black solar panel mounting kit, including 6 brackets (4 courners and 2 sides) and cable gland. They are ideal for fixing our solar panels to any vehicle, caravan, boat, barge or even outbuildings and sheds to provide a strong, secure and aesthetically pleasing fixing method, the mounts will support the solar panel at the correct height above the surface to enable the flow of air underneath the panel and keep it cool, ensuring the solar panel functions at it's optimum. The mounts can be safely bonded to the surface removing the need to drill holes. The panel is secured by screwing or bolting it to the mounting corner, but the corner itself can be fixed with a good strong adhesive like 'Sikaflex' or 'CT1' or any polyurethane sealant to the roof. (Ensure the roof is clean and dry before attaching. If a painted roof ensure the paint is not flakey)
ABS mounts raise the panel by 25mm. Edge of panel to edge of ABS is 55mm.
We sell CT1 which is great for sticking these down, please see related products tab for different colours avaialble.
If you are fitting to a vehicle we recommend that you additionally bolt or screw the panel and mounting down as well, as the strength of these systems is only as strong as the roof type or paint on your roof!
NOTE - You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method...
Here is a good tutorial to get you started:
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Class 5 flexible tinned copper conductor
Halogen-free cross-linked compound
Halogen-free cross-linked, flame retardant compound
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
For use with our stick down panels and ABS mounting kits - also great for sealing cable holes
CT1 will successfully bond:
Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.
Simple DIN mount rail 10cm long for DC or AC DIN mount breakers. Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it. Quick easy and simple solution to install breakers to your solar system.
Use with our: