NOTE - This product has cheaper delivery to business addresses.

6v Trojan Battery T105, 225Ah

Manufactured by Trojan, the market leader in quality Deep Cycle manufacturing.

Consumer and trade recognised brand.

Renowned quality.

SPR-P6-400-BLK

Enhanced Power Density
With high efficiency, LID-resistant solar cells (G12, 210mm), a lower temperature coefficient, and front-side conductive wires that support increased current collection, SunPower Performance panels are uniquely engineered to deliver more lifetime energy over standard solar panels.
 

Proven Reliability
A proprietary shingled-cell design maximises durability in all types of weather conditions—including reinforced cell connections that withstand the stresses of daily temperature swings, redundant electrical paths that alleviate the impact of cell cracks, and an advanced electrical architecture that is more resilient to the effects of shade and mitigates hot-spot formation.

Victron pure sinewave output, high peak power and high efficiency in a compact unit. Models range from 250VA to 1200VA with UK socket - other socket outlets available on request

These inverters allow you to power domestic equipment - requiring 230VAC - using 'leisure' or 'automotive' batteries rated at 12V

Bulit in DC fuse in all models but not replaceable in all models - see the manual for further details on which models carry the replaceable fuse.

Consider adding a battery isolator switch https://www.bimblesolar.com/300a-blue-sea-battery-isolator

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level Monitoring:

• In- and output voltage, % load and alarms

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector

Spec Sheet

See the Download tab on this listing

New XTRA series - G3-BLE *NEW* Integrated Bluetooth

NOTE - The MT50 display unit does not work with this model, you need the MT52 instead.

For 12V Solar System: 520W solar panel (150V for max input voltage)
For 24V Solar System: 1040W solar panel (150V for max input voltage)

Introducing the XTRA-N G3/XTRA-N G3 BLE series controllers—a cutting-edge solar charge control solution. With a built-in Bluetooth module for easy mobile app parameter control, advanced MPPT algorithms for efficient energy tracking, and features like independent voltage regulation and comprehensive electronic protections, these controllers provide a reliable and durable solution for a variety of solar applications, from RVs to household systems. Upgrade your solar experience with the XTRA-N G3 series.

• High quality and low failure rate components of ST or IR to ensure the service life
• Advanced MPPT technology & ultra-fast tracking speed, tracking efficiency is up to 99.5%
• Maximum DC/DC transfer efficiency is as high as 98.5%; full load efficiency is up to 97.2%
• Advanced MPPT control algorithm to minimize the lost rate and lost time
• Accurate recognizing and tracking of multi-peaks maximum power point
• Wider MPP(maximum power point) running voltage to optimize PV utilization
• Support multi battery types including lithium batteries
• Equipped with a stable self-activation function for the lithium battery
• Set the battery voltage parameters on the LCD
• Battery temperature compensation
• Limit the charging power & charging current to no higher than the rated value
• Real-time energy statistics function
• Charging power reduction automatically for over-temperature
• Built-in Bluetooth to adjust settings through EPEVER APP
• RS485 communication interface with optional 4G or Wi-Fi modules for remote monitoring
• Setting parameters via the PC software, APP, or remote meter
• Constant voltage output function
• Comprehensive electronic protections
• Multiple load work modes
• Dustproof and waterproof design with IP33 enclosure
• Low self-consumption, lower than 10mA
• Operation at full load without charging power reduced in the working temperature range

Ready assembled VSR bundle

Ready assembled bundle with a 6 + 1 metre pre-assembled heavy duty wiring harness with twin fuses. The bundle is manufactured using 2 x midi fuse holders & 16mm2 / #6 AWG heavy duty extra flexible battery cable.

Bi-Directional, zero loss Split Charging
Fully automatic operation
‘Connected’ LED indicator
Sealed for marine/under hood installation
Ignition Protected

Very simple to install, does not require a connection to vehicle alternator

Fully epoxy sealed unit for years of trouble free service

Only 3 Connections to make

Power in, Power out & negative...that's it!
The idea of a "voltage sensitive relay" (VSR) or "voltage controlled relay" (VCR) as they are sometimes known,  is to simplify the installation, no connection is made to the vehicles alternator .

Simply connect this relay to the towing vehicles positive battery terminal (via a fuse!) and link to the leisure battery
The relay monitors the towing vehicles battery voltage and when it reaches 13.3vdc, the relay switches on and supplies charging current to the aux. circuits.  When the engine is stopped and the voltage of the vehicles main battery drops below 12.8vdc the unit switches off.
Only 3 connections are required to the unit and as such it can be fitted in next to no time .
Supplied with detailed full colour  instructions.

Switch on voltage 13.7vdc

Switch off voltage 12.7vdc

Dimensions:-65 x 65 x 53mm

Relay connections:- 2 x 6mm studs for power in and out. 1 x 450mm cable for negative

Please Note: Do not use on Euro V/VI engines, or engines with smart alternators or regenerative brakes.  These newer systems do not give a constant voltage and are not suitable for this split charge relay, please use this instead Programmable relay

Long Aluminium Mounting Brackets - Stick down on Boats - Rivet down on vans

Use one pair for up to 100w panels and 2 pairs larger panels.  Three or more pairs for the largest panels over 2m long is highly recommended.  Bear in mind judgement is important when using this guidance, each fit is different and you need to judge the best fit for yourself.

Specification:
Foot print (550mm long, 75mm wide)
Rivet plate 25mm
Panel ledge 30mm

Height 59.5mm

The panel will sit 2.5cm up on the ledge from the plate that is riveted / bolted to the substrate (roof).

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Ideally 6mm solar cable max - for bigger units with bigger cable click here

Unit best used for housing 1 x AC RCBos, string fuse holders and fuses up to 32a as opposed to DC Din Mount breakers.

Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit.  If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.

This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.  

You will also need suitable cable entry glands - please see related products tab.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

This breaker can take up to and including 25mm2 cable.

A small, low cost multimeter supplied with test leads and holster.

• 3½ digit, 1999 count display
• AC/DC voltage measurement
• DC current
• Resistance measurement (20R to 2MR)
• Diode, continuity and transistor tester
• Square wave output
• Low battery indication
• Requires a 9V PP3 battery (included)

DMM Functions: DC Current, AC/DC Voltage, Continuity, Diode, Resistance, Transistor
No. of Digits: 3.5  
DMM Response Type: Average  
Display Count: 1999  
Range Selection: Manual  
Voltage Measure DC Max: 500V  
Voltage Measure AC Max: 500V  
Current Measure DC Max: 5A  
Resistance Measure Max: 2Mohm