The Phoenix Inverter Smart is an efficient and reliable inverter. Built on our proven and field tested Phoenix inverter platform, it now comes with a new slimmer design and full metal casing. Models are available in 1600VA, 2000VA and 3000VA for 12, 24 or 48V systems.

It’s powerful enough to supply most common plug in appliances in your car, boat, caravan or home. A toroidal transformer provides a high peak power surge capacity, stable voltage, frequency and high quality sine-wave.  

Installation is simpler than ever before with terminals now more accessible for the installer, enabling a more professional finish. 

Bluetooth is built-in, and makes setting up your high power inverter easier than ever before.
Configure alarms, alarm relay, voltage cut-off, output voltage, frequency, eco-mode and more, all from within VictronConnect.

Features:

• Low battery voltage alarm  
• Low battery voltage cut-off and restart levels 
• Dynamic cut-off: load dependent cut-off level 
• Output voltage: 210 - 245V 
• Frequency: 50 Hz or 60 Hz 
• ECO mode on/off and ECO mode sense level 
• Alarm relay 

Monitoring: 

• In- and output voltage, load and alarms 

Discover more about Dynamic Cut off here

VE.Direct communication port
The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable needed) to configure and monitor the same parameters.

Proven reliability
Inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature.

High start-up power
Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools.

ECO mode
When in ECO mode, the inverter will switch to standby when the load decreases below a preset value. Once in standby the inverter will switch on for a short period every 2,5 seconds (adjustable). If the load exceeds the preset level, the inverter will remain on.

Remote on/off
A remote on/off switch or relay contact can be connected to a two pole connector. Alternatively, the H terminal (left) of the two pole connector can be switched to battery plus, or the L terminal (right) of the two pole connector can be switched to battery minus (or the chassis of a vehicle, for example).

Warranty: Five Years

Download Datasheet

Four x 6v Trojan Battery T105, 225Ah

Manufactured by Trojan, the market leader in quality Deep Cycle manufacturing.

Consumer and trade recognised brand.

Renowned quality.

6 Volt  (220Ah @ 20hr rate - 180Ah @ 5hr rate).

26kg - 264mm length x 181mm wide x 276mm high.

Terminals available as M8 stud LPT.

This product has cheaper delivery to business addresses.

Used 250W Bisol Solar Panel from Leading EU manufacturer Bisol.  Dimensions:  1649 X 991 X 40mm

Bargain! Please read below about panel condition

These are all working and outputing power as you would expect.  As a used panel they may have some scratches and may need cleaning. They have been installed for around 4 years and were only removed to increase the capacity of the solar farm with larger panels.  We have them at a wonderful low price :-)

Please note: These panels do not have MC4 connectors, they have an older connector, you can use these existing connectors to connect the panels together, but you will need to cut off the connectors on the end of the string and replace with MC4s.

MC4 listing - Click here to purchase

BiSol

BISOL Group is a European manufacturer of premium photovoltaic modules and mounting systems, offering a range of solar solutions available in more than 70 countries worldwide. At BISOL Group, the world’s leading experts are raising industry standards and inventing creative solutions. Because we design products that offer the strongest lifetime energy yields, green energy has become more attractive than ever before.

Attention to international standards

We run international operations from our representative offices in Belgium, France, Italy and the United Kingdom. At all stages of the production process we operate in accordance with international standards ISO 9001 (Quality management systems), ISO 14001 (Environmental management systems) and OHSAS 18001 (Occupational health and safety management systems). As quality comes first, all inconsistencies are detected and dealt with immediately. The company works in accordance with legislative frameworks and takes into account both safety and health directives, and internal rules. 

Responsibility towards communities

We strive to help our employees and the communities we work in. Through the years, we have worked hard to create jobs, raise awareness of renewable energy’s importance and contribute to the development of the photovoltaic industry. We are especially passionate about educating the youngest generations, who are our hope for the future.

Download Specsheet

You will want to use a 20A MPPT for 1 panel on a 12V system.

For 12V Solar System: 750W solar panel (150V for max input voltage 138V@ 25C)
For 24V Solar System: 1500W solar panel (150V for max input voltage 138V@ 25C)
For 48V Solar System: 3000W solar panel (150V for max input voltage 138V@ 25C)

No Fan for silent operation, great for vans, boats or any live in spaces

​The AN tracer models have a current limiting function, you can connect twice the rated power to the controller ​so if your on a budget you can use a smaller controller with more panels so that you get more power in winter or low light but don't risk overloading the controller in the summer.  The output will be limited to the max listed above.

Supports upto 8 units in parallel with a PTA adapter for communication and equalize of the paralleled units

Local temperature sensor included, remote 3m temperture sensor optional.

Tracer AN series controller, based on multiphase synchronous rectification technology (MSRT) and advanced MPPT control algorithm, with dual-core processor architecture and common negative design, has the features of high response speed, high reliability, and high industrial standard. MSRT can guarantee very high conversion efficiency in any charge power, which sharply improves the energy efficiency of solar system; Advanced MPPT control algorithm minimize the maximum power point loss rate and loss time, to ensure the tracking efficiency, corresponding speed as well as high conversion efficiency under high or low power, so that in any situation, Tracer AN products can rapidly track the maximum power point (MPP) of PV array to obtain the maximum energy of the panel. The limitation function of the charging power and current and automatic power reduction function fully ensure the stability when works with oversize PV modules and operate under high temperature environment.

With the adaptive three-stage charging mode based on digital control circuit, Tracer AN series controllers can effectively prolong the life-cycle of battery and significantly improve the system performance. The load, utility or generator auto-control relays make it easy to compose the hybrid power system. All-around electronic protections, including overcharging, over discharging, and PV reverse polarity protection, effectively ensure the safer and more reliable operation of the solar system for a longer service time. The isolated RS485 interface with standard MODBUS communication protocol and 5V power supply makes it easy for customer to expand the application, Support up to 8 charging in parallel to expand system and meet with different monitoring requirements, so that can be widely used for various applications, e.g. solar RV, household system and field monitoring, etc.

Features

• CE certification(LVD EN/IEC62109,EMC EN61000-6-1/3)
• High quality & low failure rate components of ST and Infineon to ensure the product’s life
• Advanced MPPT technology & ultra-fast tracking speed is up to 99.5% guaranteed
• Maximum DC/DC transfer efficiency is as high as 98.7%
• Advanced MPPT control algorithm will minimize the MPP loss rate and loss time
• The accuracy of the recognition and tracking at the highest point of multiple-peaks MPP
• The wider range of MPP operating voltage.
• Auto control system to limit the charging power & current go over the rated value.
• Support 4 charging options: Sealed, Gel, Flooded and User.
• Battery temperature compensation function
• Real-time energy recording and statistical function
• Automatic over-temperature power reduction function
• Hundred percent full load operation in working environment temperature range within charging & discharging
• Support up to 8 units in parallel to expand system
• Load relay control external load switch signal to realize diversified load work modes
• The first and the second disconnection of load control, contain two relay’s contact.
• Auto-control of utility and generator relay design
• Utility or generator auto-control relays make it easy to compose the hybrid power system
• The remote temperature and the voltage sensor design will collect accurate data of battery temperature and voltage
• Isolated RS-485 with 5VDC/200mA to protect output for no power devices with MODBUS protocol
• To monitor or set the parameters by using the phone Apps or PC software.

Protection:

• PV Over Current/power • Night Reverse Charging • Battery Overheating
• PV Short Circuit
• Battery Over Voltage
• Controller Overheating
• PV Reverse Polarity
• Battery Over Discharge
• TVS High Voltage Transients

 1At minimum operating environment temperature;
2At 25°C environment temperature
3The maximum PV open circuit voltage must never exceed 138V or 180V at 25°C environment temperature.

Download Manual 

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 10m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

50mm Cable - Use for connecting Batteries to Inverter

You will need 2 cables, 1 for Positive and 1 for Negative

If you need a longer cable please let us know.

50mm Cable - Use for connecting Batteries to Inverter

You will need 2 cables, 1 for Positive and 1 for Negative

If you need a longer cable please let us know.

One pole fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or charge controller and battery. Integrated handle enabling use as an isolator.

NH00 rated at 250VDC, 160A

Choose NH00 or NH000 fuse separately

Item dimensions 170mm H X 42mm W X 80mm D

STÄUBLI MC4 Solar PV connectors - Pair 

Connect your solar modules together with ease using these safe and durable genuine Staubli MC4 connectors. Snap-in lock. MC4 crimp tool required to make onto cable ends. https://www.youtube.com/watch?v=qjIdrBsim5s

Suitable for 4mm² and 6mm² solar cable with an outside diameter of 5.9 - 8.8mm,  Part number: 32.0017P2000-UR & 32.0016P2000-UR

Product information:

*Please note male and female refers ot the metal conductor and not the plastic insulator*

Battery Inter-connecting Cable - 35mm cable with M8 - M8 Lugs (M8 on both ends)

Made up to size for you for connecting your batteries together.

Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 2.5m lengths MC4 to bare wire)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

10mm cable - Charge Controller to Batteries - 2 Meter with M8 Lug

You will need 2 cables per charge controler (Pos & Neg).  The Lugs are on 1 end only as the charge controllers have bare wire connectors.

If you need longer please let us know

STÄUBLI MC4 Solar PV connectors - Pair of Y Branches

Connect your solar modules together with ease using these safe and durable MC4 connectors.  This pair of "Y" shape connectors (one in a male to female, female configuration, and one in a female to male, male configuration) will allow you to connect panels or strings of panels together.  If you need to connect 3 panels together then it is cheaper to use 2 pairs of these than to purchase a 3 way splitter (its about 1/3 of the cost to use these)

Product information:

NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC

Fits https://www.bimblesolar.com/DC-fuse-disconnect-1pole

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

Simple DIN mount rail 10cm long for DC or AC DIN mount breakers.  Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it.  Quick easy and simple solution to install breakers to your solar system.

Use with our:

• DC DIN mount breakers
• RCBO AC breakers.