Suitable for a small house, or mobile home/boat, this will provide 1.66kWp of Perlight 415W all black panels, along with a Victron 24V Multiplus 1600VA Inverter Charger and 2 x 230Ah Sterling AGM batteries.
The new style MultiPlus is set to replace the earlier MultiPlus Compact range. It is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology and a high-speed AC transfer switch in a single compact enclosure.
Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
PowerControl - Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist - Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low.
TNE Series, TN’s most powerful products, are specially designed for deep cycle application. With numbers of national patent technologies, the cycle life reaches 400-600 cycles at 100% DOD, highly suitable for golf carts, electric wheelchairs, low-speed electric vehicles etc. Maintenance free technology reduce the complexity with water adding during use and become more and more popular in the market.
Float Service | Cycle service Normal | Cycle service Fast recharge | |
Absorption | 14,2 - 14,6 V | 14,6 - 14,9 V | |
Float | 13,5 - 13,8 V | 13,5 - 13,8 V | 13,5 - 13,8 V |
Storage | 13,2 - 13,5 V | 13,2 - 13,5 V | 13,2 - 13,5 V |
Brand |
TN Power |
---|---|
Manufacturer Part Number |
TNE12-230 |
Voltage |
12 |
Capacity (C20) |
230 |
Terminal Type |
I7 |
Terminal Layout |
Side |
Dimensions (Including Terminals) |
L532 x W207 x H220mm |
Weight |
59Kg |
Warranty |
2 Years |
Battery Technology |
AGM |
FOR LARGE PANEL DELIVERY TIMES, SCHEDULES AND COSTS - CLICK HERE
415W Perlight Solar Panels Mono Percium - All Black, 1719 x 1140mm x 30mm
The Triple Black DELTΔ SERIES cell module from Perlight has proven extremely popular in the UK due to its sleek looks and diminutive size.
It is completely black with black busbars, a black back sheet and a black frame, which when installed in arrays, offers a more uniform appearance, enabling PV modules to integrate into new and existing buildings without necessarily making the array the focal point.
Not just aesthetically pleasing, the 415W Delta Black Monocrystalline module has PERC technology which essentially enables to improve light capture near the rear surface and to optimize electrons capture.
This module continues the trend from Perlight of well made, good looking products that offer outstanding value for money.
The Black Plus Series is an excellent all-round module, which is sleek and robust. Proven performance, stylish appearance and high-efficiency monocrystalline PERC cells. Concealed link busbars at either end of the module provide a more elegant finish than other black modules on the market. Crafted with precision and expert skill, the Black Plus Series offers outstanding build quality and reliability.
Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel.
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMUM Order.
MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN(long-range wide area network) device, available optionally.
Optional SmartSolar Control Display
By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.
VictronConnect
VictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.
Victron MK3-USB Configuration Interface
The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.
Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.
Supported Platforms
The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.
**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**
Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.
The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.
NH00 rated at 250VDC, 160A,
Choose NH00 or NH000 fuses separately
Product measures 170mm H X 84mm W X 80mm D. Surface mountable.
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you could cut in half giving you 2 x 1m lengths MC4 to bare wire)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Insulates battery terminals which have in-line dual posts or similar such as our product https://www.bimblesolar.com/battery-terminals-m8-pair
Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line
Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.
The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.
This item fits String Fuse holder
One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.
Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off the supply to a solar charge controller or solar inverter.
Choose fuse separately
Item dimensions 75mm H X 16mm W X 55mm D
NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.
Fuses are rated at 250VDC
Simple DIN mount rail 10cm long for DC or AC DIN mount breakers. Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it. Quick easy and simple solution to install breakers to your solar system.
Use with our: