The Pylontech US3000C has an incredible DoD of 95%.
Advantages
You can now register the Pylon US3000C for an additional 3 years of manufacturer warranty for free. Go to Pylon Support and complete the information in the 'sign up battery' page.
The US3000C can be used to expand an existing US3000 bank. Please note, the US3000C needs to be used as the master battery when used to expand an existing US3000 bank.
DIP switch has been deployed reversely. ON is down, OFF is UP. If DIP switches need to be 1000 then set it to 1110. MAX DISCHARGE AND CHARGE RATE IS ONLY APPLICABLE FOR +- 60 SECONDS
If using this battery with Victron equipment it requires a Type A communications cable to the Victron GX device not a Type B.
You can optionally add mounting brackets BRACK-US3000 to this product for a stable base, and to allow easy stacking of multiple units.
If you want to use these batteries with Victron equipment please read this article to select the correct equipment:
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.
The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.
Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.
Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
MultiPlus-II inverter/charger.
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.
GX device
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.
Super High Efficiency Mono PERC Module (CS3L-370MS) Dimensions: 1765 X 1048 X 35mm
CANADIAN SOLAR INC.is committed to providing high quality solar products, solar system solutions and services to customers around the world. As a leading PV project developer and manufacturer of solar modules with about 30 GW deployed around the world since 2001, Canadian Solar Inc. is one of the most bankable solar companies worldwide.
With proprietary mono wafer and cell technologies Canadian Solar have developed an extraordinary module rage. Combining the best technology and design, it also reduces LCOE and installation costs.
The Super High HiKu mono modules with dimensions of 1765 x 1048 x 40mm, have the following unique features:
MORE RELIABLE (THANKS TO HALF CUT CELL TECHNOLOGY):
Cell: 120 x dual-cell Mono, 156 x 78 mm
Dimensions: 1765 x 1048 x 35 mm
Weight: 20.5 kg
This cabinet is suitable for housing of up to 4 x Pylontech US2000B Plus/V2/C Lithium-Ion batteries or 2x US3000/C Lithium-Ion batteries. Dimensions assembled - W 550mm X D 550mm Each cabinet comprises a welded steel frame and adjustable front and rear 19” mounting profiles. The cabinets feature ventilation slots in the top, have a lockable glass front door, and removable sides. The cabinet is finished in a high quality attractive black. Batteries need to be attached using front battery mounting holes. Ready assembled
NOTE - Battery stacking, weight of batteries needs to be supported by additional means, we recommend unistrut or angle on the sides or back. 19" Server trays can also be used, sourced independently.
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 10m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Victron MK3-USB Configuration Interface
The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.
Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.
Supported Platforms
The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.
Mechanical Hexagonal crimp tool for 10mm² -120mm² copper tube terminal lugs. For manual crimping of terminal lugs and pin ferrules onto battery cable. 45cm long handles.
125A Fuse for 48V systems
For use with Mega Fuse Holder
300A Battery isolator switch, 900A for 30 secs, up to 48 Volt, M10 connection. Can be use on 12, 24 or 48 Volt system as long as switch current rating is not exceeded.
M-SERIES BATTERY SWITCHES
300 Ampere continuous rating.
Regulatory
Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 2.5m lengths MC4 to bare wire)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Pylon battery cable accessory kit for use with the US2000B, US2000B Plus and Phantom-S models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the charger.
You require one cable pack per system for the following batteries, with a maximum of 5 x US2000B batteries or 3 x US3000 or 2 x UP5000. With a system of more batteries than mentioned, an additional cable pack would be required accordingly.
This cable pack includes the following cables:
2 x 2m long power cables (positive and negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.
1 x 3.5m RJ45 Communication cable (Not for CAN communication)
STÄUBLI MC4 Solar PV connectors - Pair of Y Branches
Connect your solar modules together with ease using these safe and durable MC4 connectors. This pair of "Y" shape connectors (one in a male to female, female configuration, and one in a female to male, male configuration) will allow you to connect panels or strings of panels together. If you need to connect 3 panels together then it is cheaper to use 2 pairs of these than to purchase a 3 way splitter (its about 1/3 of the cost to use these)
Product information:
Technical data | |
Connector system | Ø 4 mm |
Rated voltage | 1500 V DC (UL) |
Rated current | 50 A |
Rated impulse voltage | 12 kV |
Ambient temperature range | -40 °C...+75 °C (UL) |
Upper limiting temperature | 105 °C (Stäubli) |
Degree of protection, mated unmated | IP67 IP2X |
Overvoltage category/Pollution degree | CATIII / 2 |
Contact resistance of plug connectors | ≤0.5 mΩ |
Safety class | II |
Contact system | MULTILAM |
Contact material | Copper, tin plated |
Insulation material | PC |
Locking system (UL) | Locking type |
Flame class | UL94-V0 |
UL recognized component, in accordance with UL 6703 | E343181 |
Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.
Mega Fuse stand alone fuse holder for the Victron Mega Fuses. M8 stud connection. Comes with translucent cover.
25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK
25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK