Please note the VSR in this kit is not suitable for Euro 5 or Euro 6 engines.
NOTE - This product has cheaper delivery to business addresses.
6v Trojan battery 6VAGM, 200ah
Manufactured by Trojan, the market leader in quality Deep Cycle manufacturing
Consumer and trade recognised brand
Renowned Quality
|
MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.
Load output
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.
325W JA Solar Panels Mono Percium - All Black Half Cell, 1689 X 996 X 35mm
Half Cell Advantages
Supplied with 1000mm output cables and QC4.10 connectors (connects to MC4s)
Percium Cell
The latest in mono cell technology with passivated backside, local BSF and 4 Bus Bars from worldwide PV Cell leaders - JA Solar
First to reach >20.6% average cell efficiency in mass production
More Power Per m²
JA higher efficiency module type specially designed for UK rooftop market.
Maximise the kWp installation on the roof
Aesthetics
Homogeneous Black Mono cells.
Black Frame for anti-glare and pleasing appearance.
Lower System Cost
Reduced installation and BOS cost
Excellent Low-light Performance
Enhanced spectral response at longer wavelength boosts low-light performance, which can produce more than 1% additional power compared with conventional module at system side.
High Reliability
Passed "3xMCS" TÜV SÜD Thresher Long life Accelerated Stress Tests.
Full range of PID-resistance tests
Harsh climate environment endurance tests
Full set of long-term reliability tests
Manufacturing inspected and certified by leading institutes such as PI-Berlin, Franhoeffer, Sgurr, OST and Solar-IF
100% in-house automatic manufacturing
2X 100% EL inspection ensuring defect-free production
Over 500MWp of JA Solar panels installed in the UK. 10GWp Worldwide.
Other Features
Positive power tolerance: -0~+5W
Modules binned by current to improve system performance
Excellent mechanical load resistance: Certified to withstand high wind loads (2400Pa) and snow loads (5400Pa)
Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel.
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
Victron pure sinewave output, high peak power and high efficiency in a compact unit. Models range from 250VA to 1200VA with UK socket - other socket outlets available on request
These inverters allow you to power domestic equipment - requiring 230VAC - using 'leisure' or 'automotive' batteries rated at 12V
Bulit in DC fuse in all models but not replaceable in all models - see the manual for further details on which models carry the replaceable fuse.
Consider adding a battery isolator switch https://www.bimblesolar.com/300a-blue-sea-battery-isolator
VE.Direct communication port
The VE.Direct port can be connected to:
• A computer (VE.Direct to USB interface cable needed)
• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)
Fully configurable:
• Low battery voltage alarm trip and reset levels
• Low battery voltage cut-off and restart levels
• Dynamic cut-off: load dependent cut-off level
• Output voltage 210 - 245V
• Frequency 50 Hz or 60 Hz
• ECO mode on/off and ECO mode sense level Monitoring:
• In- and output voltage, % load and alarms
Proven reliability
The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.
Remote on/off
A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector
Spec Sheet
See the Download tab on this listing
Ready assembled kit with a 6 + 1 metre pre-assembled heavy duty wiring harness with twin fuses. The kit is manufactured using 2 x midi fuse holders & 16mm2 / #6 AWG heavy duty extra flexible battery cable.
Very simple to install, does not require a connection to vehicle alternator
Fully epoxy sealed unit for years of trouble free service
Only 3 Connections to make
Power in, Power out & negative...that's it!
The idea of a "voltage sensitive relay" (VSR) or "voltage controlled relay" (VCR) as they are sometimes known, is to simplify the installation, no connection is made to the vehicles alternator .
Simply connect this relay to the towing vehicles positive battery terminal (via a fuse!) and link to the leisure battery
The relay monitors the towing vehicles battery voltage and when it reaches 13.3vdc, the relay switches on and supplies charging current to the aux. circuits. When the engine is stopped and the voltage of the vehicles main battery drops below 12.8vdc the unit switches off.
Only 3 connections are required to the unit and as such it can be fitted in next to no time .
Supplied with detailed full colour instructions.
Switch on voltage 13.7vdc
Switch off voltage 12.7vdc
Dimensions:-65 x 65 x 53mm
Relay connections:- 2 x 6mm studs for power in and out. 1 x 450mm cable for negative
Please Note: Do not use on Euro V/VI engines, or engines with smart alternators or regenerative brakes. These newer systems do not give a constant voltage and are not suitable for this split charge relay, please use this instead Programmable relay
Long Aluminium Mounting Brackets - Stick down on Boats - Rivet down on vans
Use one pair for up to 100w panels and 2 pairs larger panels
Specification:
Foot print (550mm long, 75mm wide)
Rivet plate 25mm
Panel ledge 30mm
A handy kit for your 12V wiring, an affordable solution using blade fuses
Kit Includes:
![]() |
Earth block 4 way |
![]() |
Blade fuse box 4way |
![]() |
Blade set |
![]() |
Cable 4mm x 10m |
![]() |
Switches x 2 |
![]() |
Spades x 4 |
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.
12V LED Fairy Lights - 10m string, coper wire that can be bent into any shape!
Specification
Durable and heat-resistant copper wire.
Flexible copper wire can easily string up how you want (don't bend tightly).
Can last for 50000+ hours! If one light goes out the rest remain lit!
Please Note: When installing do not trap the wires between objects that could crush the cables, and do not wrap tightly around screws or nails, this can brake the wires and then cause the lights to short out.
LED Quantity: 100LEDs
Chips:3014 SMD
Length: 10meter
Power: DC12V
Connector: 2.1mm barrel socket
Max 6w
Light colour: warm white
Wire color: Copper
Modes: Steady on
12V Dual USB socket, surface mount or replace cigarette lighter socket with USB sockets.
Color: Black
Size:8.3*5.5*5*3.7CM
Material: Aluminum alloy
Suitable for voltage: 6V-28v
The output voltage:12v
Output Current:3.1A
Battery Inter-connecting Cable - 35mm cable with M8 - M8 Lugs (M8 on both ends)
Made up to size for you for connecting your batteries together.
Cable Gland Entry Box, use to connect through external surface. Perfect for solar panel cables coming from outside to controller.
A small, low cost multimeter supplied with test leads, perfect to help you setup and test your solar installation.
DMM Functions: DC Current, AC/DC Voltage, Diode, Resistance
No. of Digits: 3.5
DMM Response Type: Average
Display Count: 1999
Range Selection: Manual
Voltage Measure DC Max: 500V
Voltage Measure AC Max: 500V
Current Measure DC Max: 5A
Resistance Measure Max: 2Mohm
Simple DIN mount rail 10cm long for DC or AC DIN mount breakers. Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it. Quick easy and simple solution to install breakers to your solar system.
Use with our: