Victron Solar 185W Mono panel 1485 x 668 x 30mm 

• Low voltage-temperature coefficient enhances high temperature operation.

• Exceptional low light performance and high sensitivity to light across the entire solar spectrum.
• 25 - Year limited warranty on power output and performance.
• 5 - Year Limited warranty on materials and workmanship.
• Sealed, waterproof, multi-functional junction box gives high level of safety.
• High performance bypass diodes minimise the power drop caused by shade.
• Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation.
• A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems.
• Highest quality, high transmission tempered glass provides enhanced stiffness and impact resistance.
• Pre wired quick connect system with PV-ST01 connectors. 

New Dual Battery MPPT series - to charge both your house battery and starter battery from 1 set of panels.

For 12V Solar System: 390W solar panel (100V for max input voltage)
For 24V Solar System: 780W solar panel (100V for max input voltage)

No Fan for silent operation, great for vans, boats or any live in spaces

With built in LCD advanced display and programming screen - with Lithium battery support 

DuoRacer MPPT charge controller is made for charging two batteries (shown as BATT1 and BATT2 below) at the same time in a solar system. This controller supports multiple life battery (BATT1) types, including Sealed, Gel, Flooded, LiFePO4, and Li-NiCoMn, which is suitable for RV, Camper, Boat, and so on. The device recognizes the start battery (BATT2) system voltage automatically, and trickle charges the battery when the conditions are satisfied.

The controller adopts the advanced MPPT control algorithm,which will minimize the maximum power point loss rate and loss time,also fast track the maximum power point(MPP) of the PV array, and obtain the maximum energy from solar array under any conditions. The energy utilization in the MPPT solar system is increased by 20-30% compared with PWM charging method. When there is no manual operation for a long time, and the charging conditions cannot be reached, the controller will turn to low-power mode, which reduces the loss and battery power waste to enhance the products life. The system parameters are shown and set by LED/LCD or the MT11 remote meter (Accessory).

The AES control signal of the car refrigerator is built in the controller, which will supply the surplus solar power to the refrigerator to avoid energy waste. The controller comes with IP33 protection level, which is waterproof and dustproof. Multiple protection features, including battery overcharge protection, over discharge protection, and reverse connection protection of the PV and battery, which effectively ensure the solar system safety, stability, and lifetime.

Product Highlights

• Maximum Power Point Tracking technology with ultra-fast tracking speed and the tracking efficiency is no less than 99.5% guaranteed
• Advanced MPPT control algorithm to minimize the MPPlost rate and lost time
• The wider range of the MPP operation voltage to improve the PV module utilization
• Auto control function of charging power & charging current limitation(BATT1)
• High quality and low failure rate components of ST, TI and Infineon to ensure the product life
• Digital circuit control of adaptive three-stage charging mode to enhance BATT1 life.
• BATT1 type can be set via LED/LCD.
• Product runs into the low-power mode when there is no manual operation for a long time, and charging conditions are not satisfied (PV<5V).
• 100% charging and discharging in operationenvironmental temperature range.
• LED and LCD dispiay units selectable.
• AES control signal for car refrigerator to avoid energy waste.
• Standard Modbus protocol, and RS485 (5V/200mA) communication port for the customer to expand the application area.

In order to connect the epever Bluetooth dongle you will need:  

 Tracer DuoRacer to Ebox WiFi or Bluetooth box cable

Epever BLE RJ45 D Bluetooth Dongle

RJ45 Female to Female Coupler

Download full spec sheet

Download Manual

Seven piece solar panel mounting kit in black ABS.

The set includes 6 brackets (4 corners and 2 sides) and cable entry gland. 

These mounts are ideal for fixing our solar panels to any vehicle, caravan, boat, barge or even outbuildings and sheds to provide a strong, secure and aesthetically pleasing fixing method.

The mounts will support the solar panel at 25mm above the surface enabling airflow underneath which keeps it cool, ensuring the solar panel functions at it's optimum.

General mounting guidance:

If using with panels equal to or under 175W, you can secure the panel by screwing or bolting it to the mounting corner.  The corner itself can be fixed with a good strong adhesive like 'Sikaflex' or 'CT1' which we sell in black white or clear.  See related products tab.  This removes the need to drill holes in your roof!  

You must ensure the roof is clean and dry before attaching.   If a painted roof ensure the paint is not flakey.

If you are using panels over 175W in size we recommend that not only do you bolt or screw the panel to the corners but additionally bolt or screw the mounting to the roof as well.

If fitting any panel to a vehicle we would recommend the belt and braces approach of bolting or screwing the panel to the mounts and additionally bolt or screw the mounts to the roof.  The strength of these systems is only as strong as the roof type or paint on your roof!

Notes:

- ABS mounts raise the panel by 25mm.  Edge of panel to edge of ABS is 55mm.

- You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method which is a good tutorial to get you started...

ABS Mounting tutorial

Optional Meter for Tracer DuoRacer MPPT charge controllers Only (20A, 30A) 

PLEASE NOTE - YOU CANNOT USE THE MT11 AT THE SAME TIME AS THE BLUETOOTH / WIFI OPTIONAL ADAPTORS

Features:
·Automatic identify  the controller, and display the type, model and relevant parameter data
·Large-screen multifunction LCD  displays all the operational data and system working status  in digital, graphic and textual forms
·With six navigation function keys, the  operation is direct, convenient and rapid
·Real-time energy statistics recording
·Both data and data flowing on the same lead ,no need for  external power
·Real-time monitoring and acoustic alarm of failure information of the controller
·Longer communication distance based on RS485 communication

·You can extend the communication cable by using your own cable, the existing 4 pin green terminals on the provided 1.5m cable and referencing the pin asignment table in the manual.

Functions Via MT11
·Diversified load control modes : manual, light ON/OFF, Light ON+ Timer, Time Control
·Battery type selection: Gel, sealed, flooded and USER type
·Real-time monitor
·Programmable parameters
·Energy display function

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Ideally 6mm solar cable max - for bigger units with bigger cable click here

Unit best used for housing 1 x AC RCBos, string fuse holders and fuses up to 32a as opposed to DC Din Mount breakers.

Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit.  If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.

This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.  

You will also need suitable cable entry glands - please see related products tab.

For use with our stick down panels and ABS mounting kits - also great for sealing cable holes

CT1 will successfully bond:

• Metals (including lead)
• Glass
• Mirrors
• Wood
• Polystyrene

Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals

• Prevents fungal growth
• UV resistant
• Excellent resistance to vibration
• Food safe - conforms to ISEGA Standards
• Works in wet or dry conditions
• Perfect for marine and boating maintenance, accident and emergency repairs
• Can be used in all salt-water environments
• Odourless
• Does not shrink
• Can be painted
• Contains no solvents
• No isocyanates
• Unique flexibility
• Environmentally compliant
• Instant repair and bonding with fibre glass and carbon fibre materials

Application
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)

Drying Time
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)

Optional Remote Temperature Sensor 

RTS300R47K3.81A

Remote Temperature Sensor

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.