App can be downloaded here: SMART BMS for Android

Can be put in series up to 48V - unlimited parallel.

5 Year warranty - Click here for Manual

• LiFePO4 24V (nominal) 150Ah 25 deg C Lithium Deep cycle
• Maximum continuous charge rate 0.5C  = 80A
• Maximum continuous discharge rate 1C =150A
• Battery must be safely charged within units parameters
• Max charge V=29.2V, Recommended =28.8V, Float V=27.6V
• Cut off voltage 20V / cutoff temperature 50 deg C
• Charge Curve style  CC/CV
• internal consumption: Operational = 10mA, Dormant 0.1mA
• 8mm ring terminal battery studs / washer
• Bluetooth interface for battery information
• App can be downloaded here: SMART BMS for Android

Victrons new 24V inverter/charger

The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid.
It has all the features of the MultiPlus, plus an external current transformer option to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing (max. 32A).  It also has all the features of the MultiGrid with built-in anti-islanding and an increasingly long list of country approvals.

PowerAssist

The MultiPlus-II will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

ESS: Energy Storage Systems

The MultiPlus-II is the key component in a Victron ESS system, providing the flexibility to combine with MPPT Solar Chargers or Grid-tie PV Inverters. For examples and more detailed information see the ESS (Energy Storage System) manual.

Uninterrupted AC power (UPS function)

In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

Remote Monitoring and Control

Monitor and control your Multi and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Multi to auto starting a back generator and more...

Download Spec Sheet

FOR LARGE PANEL DELIVERY TIMES, SCHEDULES AND COSTS - CLICK HERE

• Listing is for one panel, just add the required number of panels to your basket.

54 CELL DELTA 295W

295W MONOCRYSTALLINE SOLAR MODULE

The 54 cell, Black Plus is ideal for UK roofs due to its compact design that allows more panels to be installed in tighter spaces to maximise the solar potential of every roof. Black Plus Series is an excellent all-round module, which is sleek and robust. Proven performance, stylish appearance and high-efficiency monocrystalline PERC cells. Concealed link busbars at either end of the module provide a more elegant finish than other black modules on the market. Crafted with precision and expert skill, the Black Plus Series offers outstanding build quality and reliability.

• 12 years product warranty
• 25 years performance warranty
• Ideal for small roofs

60A MPPT with max VOC 150V - with barewire terminals (contact us for MC4 terminals)

MPPT: Ultra Fast Maximum Power Point Tracking

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remote Monitoring and Control

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN(long-range wide area network) device, available optionally.

Optional SmartSolar Control Display

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.

VictronConnect

VictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.

Download full spec sheet

Victron Phoenix Smart IP43 Charger 24/25(1+1) 230V

With boat owners in mind this adaptive 5-step charger can provide either 30A or 50A of charge to each of three battery banks. Or the Phoenix 1+1 model provides 3A to the starter-battery, the rest to the ‘house’ bank. 24V models are available with 16A/25A charge. Bluetooth enabled, you can monitor the charger and set alarms straight from your phone. Adaptive, intelligent, dynamic charge features – see the datasheet on the downloads tab. 

You must purchase the following mains lead to power this unit as it doesn't come with one or a means to wire one in: https://www.bimblesolar.com/victron-charger-mainslead

The New Victron Cerbo-S GX is the all-new communication-centre allowing you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch 50, a MFD or our VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way.

The 'S' version has most of the functionality of the full version, but some of the comms ports are removed, for a simplified solution, where temperature sensors and tank level sensors are not required.

The GX Touch 50 is the display accessory for our Cerbo GX. The five inch a touch screen display gives an instant overview of your system and allows to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, its super slim waterproof design, top-mountable setup and its simple installation bring a lot of flexibility when creating a crisp and clean dashboard. 

The display comes with a 2m long HDMI and USB cable for connection to the Cerbo GX.

Download full specsheet

A modular heavy duty DC bus bar with locations for four DC fuses. It has a positive and negative bus bar.  The Lynx distributor can link (piggy back) onto each other to form a larger bus bar for a variety of applications. For use stand alone or with the Lynx modular system, see manual under the downloads tab.

It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar https://www.bimblesolar.com/Victron-lynx-powerin

The Smart Battery Shunt

The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.

The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.
The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.

This unit has M10 bolts.

300A Battery isolator switch, 900A for 30 secs, up to 48 Volt, M10 connection. Can be use on 12, 24 or 48 Volt system as long as switch current rating is not exceeded.

BLUE SEA M-SERIES SELECTOR SWITCHES

M-SERIES BATTERY SWITCHES

300 Ampere continuous rating.

• Tin-plated copper studs for maximum conductivity and corrosion resistance
• Studs accept 3⁄8" (M10) ring terminals
• 7⁄8" (22mm) stud length accepts multiple cable terminals
• One-piece terminal stud design never loosens over time
• Case design allows surface or rear panel mounting options
• Label with international legends
• Tactile indicator conveys knob position by feel

Regulatory

• CE marked, ISO 8846
• UL Listed - UL 1107 electric power switches
• Meets ABYC requirements
• Meets UL1500 and SAE J1171 external ignition protection requirements
• IP66 protects against powerful water jets

Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 2.5m lengths MC4 to bare wire)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Kraus & Naimer DC Switch

Switch - Disconnectors, 2 pole - for single string

•            IP66/67 Protection

•            Black/Grey Padlockable Handle – lockable in the OFF-position

•            Class II compliant, Grey Insulated Enclosure

•            Switch Interlocked with lid to prevent opening in “ON” position

•            Rated for use in ambient temperatures of 50°C

Plastic Enclosures, Protection IP66/67, totally insulated, M20/M25 knock-outs
Handle black, Plate Backing grey
Contact development: 2 pole, 6 contacts per circuit (2 x 3 in series)
Dimensions (w x h x d): 100mm x 178mm X 93mm

The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.

12/24V auto ranging
The BatteryProtect automatically detects system voltage

Programming made easy
The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen.

A special setting for Li-ion batteries
In this mode the Battery Protect can be controlled by the VE.Bus BMS.
Note: the Battery Protect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.

Ultra low current consumption
This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.

Over voltage protection
To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V.

Ignition proof
No relays but MOSFET switches, and therefore no sparks.

Delayed alarm output
The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.

Delayed load disconnect and delayed reconnect
The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected.
The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.

The VE.Direct cable is used for comunication between Victron VE Direct devices. For example it can be used to connect a Victron battery monitor to the Victron Colour Control or to connect a Victron GlobalLink 520 to a Victron MPPT Controller that has a VE direct port.

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

250A Fuse for 12v or 24 systems - Pack of 5 fuses

For use with Mega Fuse Holder

STÄUBLI MC4 Solar PV connectors - Pair of Y Branches

Connect your solar modules together with ease using these safe and durable MC4 connectors.  This pair of "Y" shape connectors (one in a male to female, female configuration, and one in a female to male, male configuration) will allow you to connect panels or strings of panels together.  If you need to connect 3 panels together then it is cheaper to use 2 pairs of these than to purchase a 3 way splitter (its about 1/3 of the cost to use these)

Product information:

Premium Enhanced Cat5e UTP Patch Cables

Communications cable for use with equipment that requires ethernet RJ45 cables. This model is 2 metres long, blue in colour and the connections are booted - partially covered as per image.

• Connectors: 50 micron gold RJ45 plugs
• Cable: UL approved Cat.5 Enhanced 24AWG stranded cable
• To reduce crosstalk, short bodied connectors maintain speed & data integrity
• Moulded design suitable for advanced and new build networks

Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you could cut in half giving you 2 x 1m lengths MC4 to bare wire)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

See Datasheet tab

See Datasheet tab

35mm squared cable end lug for crimping onto 35mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK 

35mm squared cable end lug for crimping onto 35mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK