Solis 6.0kW Storage Hybrid / Pylon 10.5kWh Package
Domestic scale hybrid storage system.
The 6.0W rated power of the Solis RHI-6.0K-48ES-5G6, when matched with three Pylon US3000C batteries, delivers up to 5.0kW of discharge power from the batteries. That's perfect for supplying some of the electrical loads in the evening.
Solis Hybrid products have a separate AC output for essential loads, so they can offer protection for certain important appliances in the event of a power cut.
Solis Hybrid inverter comes with an energy meter and communication interface built in. The Cat5e cable for connecting the inverter to the battery and a longer length for connecting the Energy Meter to the inverter are both included. We can also supply longer lengths of Cat5e cable, should your particular site require them.
The Pylontech US3000C has an incredible DoD of 95%.
You can now register the Pylon US3000C for an additional 3 years of manufacturer warranty for free. Go to Pylon Support and complete the information in the 'sign up battery' page.
The US3000C can be used to expand an existing US3000 bank. Please note, the US3000C needs to be used as the master battery when used to expand an existing US3000 bank.
DIP switch has been deployed reversely. ON is down, OFF is UP. If DIP switches need to be 1000 then set it to 1110. MAX DISCHARGE AND CHARGE RATE IS ONLY APPLICABLE FOR +- 60 SECONDS
If using this battery with Victron equipment it requires a Type A communications cable to the Victron GX device not a Type B.
You can optionally add mounting brackets BRACK-US3000 to this product for a stable base, and to allow easy stacking of multiple units.
If you want to use these batteries with Victron equipment please read this article to select the correct equipment:
Solis new 5G Hybrid inverter range that supprt power for important loads during load shedding as well as saving power during peak demands. Making this the ideal solution you always wanted.
NB: This product is not suitable for use with Lead acid/Lead Carbon batteries and although supported, will not be covered under the European warranty. The Solis inverter is not able to accurately monitor the state of charge for lead acid batteries.
Fanless design IP65
High charge and discharge efficiency
Multiple work modes resulting in max self-consumption
Intelligent BMS function
24 hour real-time intelligent energy management
Remotely control & upgrade
A set of battery brackets which allows vertical stacking of the Pylon US3000 battery unit. 1 set required per battery.
**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**
Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.
The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.
NH00 rated at 250VDC, 160A,
Choose NH00 or NH000 fuses separately
Product measures 170mm H X 84mm W X 80mm D. Surface mountable.
Pylon battery cable accessory kit for use with all the different battery models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the inverter/charger.
Please check the number of cable packs you need, according to your inverter/charge specifications. Each cable pack is rated at 100A continuous, and 125A peak.
This cable pack includes the following cables:
2 x 2m long power cables (1x positive and 1x negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.
1 x 3.5m RJ45 Communication cable (Not for CAN communication)
Kraus & Naimer AC Switch
Suitable for single phase AC connection.
Plastic enclosures, protection IP66/67, totally insulated, knock-outs.
Handle red, lockablein in the OFF-position, yellow plate backing
Dimensions (w x h x d): 100mm x 190mm X 93mm
Switch interlocked with lid to prevent opening in ‘ON’ position
NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.
Fuses are rated at 250VDC
25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK