NEW 1000ah c20 (840 ah c5)
2 VOLT, DEEP CYCLE WITH TUBULAR POSITIVE PLATE, 1500 CYCLE LIFE EXPECTANCY TO 80% d.o.d
198mm x 119mm x 694.5mm height, 47.6kg wet
Charge Voltage Settings
Bulk/Absorb 2.40v per cell
Float 2.23v per cell
EQ 2.47v per cell
325W JA Solar Panels Mono Percium - All Black Half Cell, 1689 X 996 X 35mm
Half Cell Advantages
Supplied with 1000mm output cables and QC4.10 connectors (connects to MC4s)
The latest in mono cell technology with passivated backside, local BSF and 4 Bus Bars from worldwide PV Cell leaders - JA Solar
First to reach >20.6% average cell efficiency in mass production
More Power Per m²
JA higher efficiency module type specially designed for UK rooftop market.
Maximise the kWp installation on the roof
Homogeneous Black Mono cells.
Black Frame for anti-glare and pleasing appearance.
Lower System Cost
Reduced installation and BOS cost
Excellent Low-light Performance
Enhanced spectral response at longer wavelength boosts low-light performance, which can produce more than 1% additional power compared with conventional module at system side.
Passed "3xMCS" TÜV SÜD Thresher Long life Accelerated Stress Tests.
Full range of PID-resistance tests
Harsh climate environment endurance tests
Full set of long-term reliability tests
Manufacturing inspected and certified by leading institutes such as PI-Berlin, Franhoeffer, Sgurr, OST and Solar-IF
100% in-house automatic manufacturing
2X 100% EL inspection ensuring defect-free production
Over 500MWp of JA Solar panels installed in the UK. 10GWp Worldwide.
Positive power tolerance: -0~+5W
Modules binned by current to improve system performance
Excellent mechanical load resistance: Certified to withstand high wind loads (2400Pa) and snow loads (5400Pa)
Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel.
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
The Radian Series GS7048E Grid/Hybrid™ (full-flexibility grid-interactive/off-grid) Inverter/Charger is engineered toward one goal: making system design and installation easier and faster in grid-interactive and comprehensive off-grid applications. The Radian Series simplifies the configuration, distribution, and implementation of energy storage through a standardized approach when integrated with an OutBack GS Load Center, making it easier than ever to provide successful solutions for virtually any residential, commercial or institutional power requirement.
The all-new 230V 50Hz Radian reflects OutBack’s ongoing commitment to clean, reliable power for homes, businesses and other facilities around the world, delivering 7,000 Watts. This model combines pure sine wave power output technology with unsurpassed surge capability to start the most demanding appliances, and are built around a unique dual-power module design which ensures high efficiency in both low and full power operation as well as redundancy in mission-critical applications.
The Radian Grid/Hybrid inverter incorporates OutBack’s FLEXgrid™ technology for full operational flexibility. Modular system architecture and simplified parallel design supports three-phase systems up to 21kW and multiple inverter arrays of up to 70kW. System integration and programming are easy with OutBack’s powerful MATE3 Control and HUB Communications Management devices. An advanced, front-vented layout provides optimum cooling in zero-clearance installations (i.e. where units are stacked next to each other). Field-serviceable design simplifies maintenance if needed, and firmware updates can be easily made in the field without specialized equipment.
|Nominal DC Input Voltage||48 VDC|
|Continuous Output Power at 25 °C||7000 VA|
|AC Output Voltage||230 VAC (212-250 VAC)|
|AC Output Frequency||50 or 60 Hz|
|Continuous AC Output Current at 25 °C||30 AAC|
|Continuous AC output Current at 25° C||30 AAC|
|Idle Consumption - Invert mode, no load||34 Watts|
|CEC Weighted Efficiency||N/A|
|Total Harmonic Distortion (Typical)||><5% THD, Max single voltage harmonic <2%|
|Output Voltage Regulation||± 2%|
|Maximum Output Current (1 ms peak)||100 AAC|
|Maximum Output Current (100 ms RMS)||70.7 AAC|
|Overload Capability (100 ms surge)||16.3 kVA|
|Overload Capability (5 second)||11.5 kVa|
|Overload Capability (30 minute)||7.9 kVa|
|AC Input Voltage Range (Adjustable)||170 to 290 VAC|
|AC Input Frequency Range||45 to 55Hz or 55 to 65Hz|
|Grid-Interactive Voltage Range||208 to 252VAC (EN50438)|
|Grid-Interactive Frequency Range (Default)||57Hz to 61Hz (EN50438)|
|AC Input Current (Maximum)||50 AAC|
|Continuous Battery Charge Output||100 ADC|
|DC Input Voltage Range||40 - 64 VDC|
|Temperature Range (rated)||0°C to 50°C (power derated above 25°C)|
|Temperature Range (maximum)||
-40°C to 60°C (functions, but does not necessarily meet all component specifications)
|Accessory Ports||Remote Temperature Sensor and MATE3/HUB Communications|
|Field Upgradable Firmware||Yes|
|Certifications||IEC 62477-1, AS4777.2, AS4777.3, EN61000-6-1, EN61000-6-3, EN61000-3-2, EN61000-3-3, AS3100, CE, RoHS compliant per directive 2011/65/EU|
|Warranty||Standard 5 Year|
|Unit Weight||125 lbs (56.7 kg)|
|Shipping Weight||140 lbs (63.5 kg)|
|Inverter Dimensions (H x W x D)||28 x 16 x 8.7" (71.1 x 40.6 x 22.2 cm)|
|Shipping Dimensions (H x W x D)||14.5 x 34.5 x 21" (36.8 x 87.6 x 53.3 cm)|
These are the best charge controllers on the market, they are solid, reliable and what we use for The Bimble Inn.
The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Technologies. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30% compared to non-MPPT controllers. Thanks to active cooling and intelligent thermal management cooling, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 104°F (40°C).
Included in all of the FLEXmax Charge Controllers are the revolutionary features first developed by OutBack Power, including support for a wide range of nominal battery voltages and the ability to step-down a higher voltage solar array to recharge a lower voltage battery bank. A built-in, backlit 80 character display shows the current status and logged system performance data for the last 128 days at the touch of a button. The integrated OutBack network communications allows FLEXmax series Charge Controllers to be remotely programmed and monitored via a MATE system display and provides unrivaled complete system integration.
FLEXmax MPPT Charge Controllers are the only choice when you demand a high performance, efficient and versatile charge controller for your advanced power system.
|Voltage||Recommended PV Max||Absolute Max|
|FLEXmax 80 Specifications|
|Nominal Battery Voltages||12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up)|
|Maximum Output Current||80 amps @ 104° F (40°C) with adjustable current limit|
|Maximum Solar Array STC Nameplate||12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC systems 6250 Watts|
|NEC Recommended Solar Array STC Nameplate||12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts|
|PV Open Circuit Voltage (VOC)||150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum|
|Standby Power Consumption||Less than 1 Watt typical|
|Power Conversion Efficiency||97.5% @ 80 Amps in a 48 VDC System - Typical|
|Charging Regulation||Five Stages: Bulk, Absorption, Float, Silent and Equalization|
|Voltage Regulation Set points||10 to 80 VDC user adjustable with password protection|
|Equalization Charging||Programmable Voltage Setpoint and Duration - Automatic Termination when completed|
|Battery Temperature Compensation||Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell|
|Voltage Step-Down Capability||Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input|
|Programmable Auxilary Control Output||12 VDC output signal which can be programmed for different control applications
(Maximum of 0.2 amps DC)
|Status Display||3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total|
|Remote Display and Controller||Optional Mate or Mate2 with RS232 Serial Communications Port|
|Network Cabeling||Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires)|
|Data Logging||Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production|
|Hydro Turbine Applications||Consult factory for approved Turbines|
|Positive Ground Applications||Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications)|
|Operating Temperature Range||Minimum -40° to maximum 60° C
(Power capacity of the controller is automatically derated when operated above 40° C)
|Environmental Rating||Indoor Type 1|
|Conduit Knockouts||One 1" (35mm)on the back; One 1" (35mm) on the left side; Two 1" (35mm) on the bottom|
|Warranty||Standard 5 year / Available 10 Year|
|Weight - Unit||12.20 lbs (5.56 kg)|
|- Shipping||15.75 lbs (7.10 kg)|
|Dimensions - Unit||16.25" x 5.75" x 4" (41.3 x 14 x 10 cm) -
(H x W x D)
|- Shipping||21" x 10.5" x 9.75" (53 x 27 x 25 cm)|
|Options||Remote Temperature Sensor (RTS), HUB 4,
HUB 10, MATE, MATE 2
|Menu Languages||English & Spanish|
The new MATE3 System Display and Controller makes it easy to program and monitor a complete OutBack Power System. An intuitive and integrated system configuration wizard makes system setup and programming quick and seamless.
The ability to set unique multi-level user passwords allows the user to secure critical system settings from unintended changes, while still allowing open access to necessary functions.
The MATE3 is packed full of features to make system management simple. The easy-to-read graphical LCD display is backlit for dark operating conditions. Improved tactile buttons and a user programmable “favorite” key give you immediate access to the features you want, while an intuitive scroll wheel interface allows for easy adjustment of system setpoints. Expandable SD card memory allows you to increase data logging capacity as well as upgrade units in the field.
A built-in clock and calendar function enables timer-based programming of inverter and charger operation. All of your settings are stored in permanent memory to eliminate the need to reprogram in the event of a system shutdown or battery replacement. The MATE3 is an Internet enabled device – simply connecting to the Internet will allow full remote system.
By adding the Mate Controller you can also use the outback inverters as a off grid/grid hybrid system allowing you to use the power from your batteries primarily and switching to use the grid when your batteries are low, thus minimising your use of the grid and ensuring you get the best use of your renewable power set-up, and yet never run out of power. Or you can configure an automatic generator start from them if needed.
The HUB-4 communication manager allows the MATE to control and monitor a maximum of four OutBack products. The inverter/chargers can be operated in a stacked or independent configuration, and OutBack MPPT charge controllers can also be used on any of the four available ports of the HUB-4. Future OutBack products will also be compatible with the HUB-4. The HUB-4 manages both the inter-inverter communications and the MATE-inverter communication. The HUB-4 also can be used with the X-240 autotransformer when series stacked to allow full surge and continuous AC load capacity of each FX to be available on either of the 120 VAC output circuits. When two or more FX inverters are stacked in a parallel or series configuration, the system automatically turns off any excess slave inverters to save power and maximize conversion efficiency. This power save system is fully automatic and works with or without the MATE connected to the system One or two MATE system controllers and displays can be connected to the HUB. One Mate is allowed to program the systems while the other MATE is able to only control and display the system operation. When using a single MATE with a HUB-4, programming can be locked out by moving the MATE from the 1st MATE port to the 2nd MATE port once programming has been completed. The maximum distance from the HUB-4 to the power conversion product should be under 10 feet. OutBack includes two 3 foot long and two 6 foot long CAT5 cables standard with the HUB-4.
6mm² Solar Cable - Price is per meter, simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Class 5 flexible tinned copper conductor
Halogen-free cross-linked compound
Halogen-free cross-linked, flame retardant compound
STÄUBLI MC4 Solar PV connectors - Pair
Connect your solar modules together with ease using these safe and durable genuine Staubli MC4 connectors. Snap-in lock. MC4 crimp tool required to make onto cable ends. https://www.youtube.com/watch?v=qjIdrBsim5s
Suitable for 4mm² and 6mm² solar cable with an outside diameter of 5.9 - 8.8mm, Part number: 32.0017P2000-UR & 32.0016P2000-UR
|Connector system||Ø 4 mm|
|Rated voltage||1500 V DC (UL) 1000V DC (IEC)|
|Rated current||39 A 4/6mm cable|
|Rated impulse voltage||12 kV|
|Ambient temperature range||-40 °C...+85 °C (TUV)|
|Upper limiting temperature||105 °C (TUV)|
|Degree of protection, mated unmated||IP65 1hr IP68 1min|
|Overvoltage category/Pollution degree||CATIII / 3|
|Contact resistance of plug connectors||≤0.25 mΩ|
|Safety class||1000 V DC: II|
|Contact material||Copper, tin plated|
|Locking system (UL)||Locking type|
|UL recognized component, in accordance with UL 6703||
*Please note male and female refers ot the metal conductor and not the plastic insulator*
16mm cable - for Large Charge Controller to Batteries - 2 Meter leght with M8 Lug
You will need 2 cables per charge controler (Pos & Neg). The Lugs are on 1 end only as the charge controllers have bare wire connectors.
If you need longer lengths please let us know
35mm Cable - Use for connecting Batteries to Inverter
You will need 2 cables, 1 for Positive and 1 for Negative
If you need a longer cable please let us know.
The OutBack Remote Temperature Sensor (RTS) is essential for proper battery charging. All OutBack Power products with integrated battery charging have temperature compensation systems built in which benefit from the installation of the RTS (included with inverter/chargers). With the RTS you can make sure that your OutBack Power System knows the precise battery temperature, so it can recharge your batteries safely and efficiently. If your system has multiple OutBack products connected to one HUB4 or HUB10, only a single RTS needs to be installed.