Charge your Electric Vehicle from Solar. This kit is designed for charging your car at night, it has 1000Ah batteries to store the solar power and then charge your EV from the stored solar energy, it has a faster 7.4Kw charger.
Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.
Two AC Inputs & two AC Outputs
The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.
Unique PowerAssist feature
The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.
Virtually unlimited power thanks to parallel operation
Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.
Remote Monitoring and Control
Monitor and control your Quattro and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more...
310W JA Solar Panels Mono Percium - All Black
The latest in mono cell technology with passivated backside, local BSF and 4 Bus Bars from worldwide PV Cell leaders - JA Solar
First to reach >20.6% average cell efficiency in mass production
More Power Per m²
JA higher efficiency module type specially designed for UK rooftop market.
Maximise the kWp installation on the roof
Homogeneous Black Mono cells.
Black Frame for anti-glare and pleasing appearance.
Lower System Cost
Reduced installation and BOS cost
Excellent Low-light Performance
Enhanced spectral response at longer wavelength boosts low-light performance, which can produce more than 1% additional power compared with conventional module at system side.
Passed "3xMCS" TÜV SÜD Thresher Long life Accelerated Stress Tests.
Full range of PID-resistance tests
Harsh climate environment endurance tests
Full set of long-term reliability tests
Manufacturing inspected and certified by leading institutes such as PI-Berlin, Franhoeffer, Sgurr, OST and Solar-IF
100% in-house automatic manufacturing
2X 100% EL inspection ensuring defect-free production
Over 500MWp of JA Solar panels installed in the UK. 10GWp Worldwide.
Positive power tolerance: -0~+5W
Modules binned by current to improve system performance
Excellent mechanical load resistance: Certified to withstand high wind loads (2400Pa) and snow loads (5400Pa)
Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel.
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
NEW 1000ah c20 (840 ah c5)
2 VOLT, DEEP CYCLE WITH TUBULAR POSITIVE PLATE, 1500 CYCLE LIFE EXPECTANCY TO 80% d.o.d
198mm x 119mm x 694.5mm height, 47.6kg wet
Charge Voltage Settings
Bulk/Absorb 2.40v per cell
Float 2.23v per cell
EQ 2.47v per cell
These are the best charge controllers on the market, they are solid, reliable and what we use for The Bimble Inn.
The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Technologies. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30% compared to non-MPPT controllers. Thanks to active cooling and intelligent thermal management cooling, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 104°F (40°C).
Included in all of the FLEXmax Charge Controllers are the revolutionary features first developed by OutBack Power, including support for a wide range of nominal battery voltages and the ability to step-down a higher voltage solar array to recharge a lower voltage battery bank. A built-in, backlit 80 character display shows the current status and logged system performance data for the last 128 days at the touch of a button. The integrated OutBack network communications allows FLEXmax series Charge Controllers to be remotely programmed and monitored via a MATE system display and provides unrivaled complete system integration.
FLEXmax MPPT Charge Controllers are the only choice when you demand a high performance, efficient and versatile charge controller for your advanced power system.
|Voltage||Recommended PV Max||Absolute Max|
|FLEXmax 60 Specifications|
|Nominal Battery Voltages||12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up)|
|Maximum Output Current||60 amps @ 104° F (40°C) with adjustable current limit|
|Maximum Solar Array STC Nameplate||12 VDC systems 900 Watts / 24 VDC systems 1800 Watts / 48 VDC systems 3600 Watts / 60 VDC Systems 4500 Watts|
|NEC Recommended Solar Array STC Nameplate||12 VDC systems 750 Watts / 24 VDC systems 1500 Watts / 48 VDC systems 3000 Watts / 60 VDC Systems 3750 Watts|
|PV Open Circuit Voltage (VOC)||150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum|
|Standby Power Consumption||Less than 1 Watt typical|
|Power Conversion Efficiency||98.1% @ 60 Amps in at 48 VDC System voltage - Typical|
|Charging Regulation||Five Stages: Bulk, Absorption, Float, Silent and Equalization|
|Voltage Regulation Set points||10 to 80 VDC user adjustable with password protection|
|Equalization Charging||Programmable Voltage Setpoint and Duration - Automatic Termination when completed|
|Battery Temperature Compensation||Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell|
|Voltage Step-Down Capability||Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input|
|Programmable Auxilary Control Output||12 VDC output signal which can be programmed for different control applications
(Maximum of 0.2 amps DC)
|Status Display||3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total|
|Remote Display and Controller||Optional Mate or Mate2 with RS232 Serial Communications Port|
|Network Cabeling||Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires)|
|Data Logging||Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production|
|Hydro Turbine Applications||Consult factory for approved Turbines|
|Positive Ground Applications||Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications)|
|Operating Temperature Range||Minimum -40° to maximum 60° C
(Power capacity of the controller is automatically derated when operated above 40° C)
|Environmental Rating||Indoor Type 1|
|Conduit Knockouts||One 1" (35mm)on the back; One 1" (35mm) on the left side; Two 1" (35mm) on the bottom|
|Warranty||Standard 5 year / Available 10 Year|
|Weight - Unit||11.65 lbs (5.3 kg)|
|- Shipping||14.55 lbs (6.4 kg)|
|Dimensions - Unit||13.5 x 5.75 x 4" (40 x 14 x 10 cm)|
|- Shipping||18 x 11 x 8" (46 x 30 x 20 cm)|
|Options||Remote Temperature Sensor (RTS), HUB 4,
HUB 10, MATE, MATE 2
|Menu Languages||English & Spanish|
Charging stations for home or private properties (indoors or outdoors)
The EVlink Wallbox is weatherproof and robust. It can therefore be used in tough environments: in homes and on private properties (condominium, corporate car park, hotel...)
Features: Charge control
> Simply connect the vehicle to the charging station: charging can start without specific action.
> Charging can be stopped and then restarted using the Stop/Start button.
> The charging power can be limited by any energy management device providing that this device is able to close a potential-free contact wired to the Wallbox.
Characteristics of the power supply network
> 220-240 V single-phase - 50/60 Hz for 3.7 and 7.4 kW charging stations
> 380-415 V three-phase - 50/60 Hz for 11 and 22 kW charging stations
> Earthing system: TT, TN or IT
Mechanical and environmental characteristics
> Ingress protection code: IP54
> Impact protection code: IK10
> Operating temperature: -30°C to +50°C
> Storage temperature: -40°C to +80°C
> Attached cable length: 4 m
> Energy management: deferred charging start or charging current limitation
(16 A to 10 A, 32 A to 16 A)
> By key lock
> 24 months for the entire EVlink range
6mm Solar Cable - Price is per meter simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable
Max load: 50A
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
10mm cable - Charge Controller to Batteries - 2 Meter with M8 Lug
You will need 2 cables per charge controler (Pos & Neg). The Lugs are on 1 end only as the charge controllers have bare wire connectors.
If you need longer please let us know
50mm Cable - Use for connecting Batteries to Inverter M8 - M10 (M8 one end M10 on the other end)
You will need 2 cables, 1 for Positive and 1 for Negative
If you need a longer cable please let us know.
MC4 Solar Connector - Price is per MC4 pair simply select the quantity as the number of MC4 pairs you want.
These are the standard connectors used on most solar panels.
TUV certified, brand new, water /weather proof rubber seal that can ensure excellent electrical contact for life time service.
The metal pin is made from high quality machined copper and sealed tip (compare to the cheap sheet metal pin) that can ensure excellent electrical contact for life time service.
Build in press tabs for easy disconnect, no tool is needed. 25A max load.
Wires should be crimped or soldered into the pins and care should be taken to get the correct pin into the correct connector. Once the pin is pushed into the connector it is difficult to remove without the correct tooling.
MC4 Main Technical Specification:
Maximum Current: 25A
Maximum voltage: 1000V
Maximum operating humidity: 5% -95% (No condensation)
Temperature: -40 ℃ ~ +90 ℃
Waterproof Grade: IP67
Flame class: UL94-V0
Connecting cable specifications: 2.5mm2 4mm2 6mm2
Test voltage: 6.6KV (50Hz, 1min)
Metal materials: nickel copper
Insulation material: PA12 * 1988HB
Lock mode: Self-locking
Security Level: Class ‖
Shell has a strong anti-aging, anti- UV capability; found in outdoor use under harsh environment requirements; according to different needs can be arbitrary and used in conjunction with a variety of cell junction box; all connections are using press-fit connection;