Brand New 200Ah Sealed Vented Lead Acid Battery
The Technology – Sterling’s high integrity valve regulated lead acid (VRLA) batteries operate as a starved electrolyte system, in which the electrolyte is limited to the amount that either is absorbed in the batteries plates or wets the fibres in the separator. The resulting system allows gases produced during overcharge to diffuse from one plate to the other and to be recombined back into the electrolyte.
This recombination creates a closed system, thus reducing the release of gases into the atmosphere under normal discharge conditions.
Since the electrolyte is recycled, there is no need to add water to the batteries. This reduced maintenance leads to longer-life battery in a clean and compact container that can be installed when flooded batteries are impractical.
Nominal Capacity | 200 AH (20 hour rate) |
Nominal Voltage | 12 volt |
Length | 522mm |
Width | 240mm |
Case Height | 222mm |
Weight | 62.57kg |
features & benefits
Tank formed construction allows for individual plates to be inspected prior to battery assembly, eliminating manufacturing defects. Plates are fully formed guaranteeing 100% capacity on delivery.
Sterling’s unique construction and sealing techniques ensures no electrolyte leakage from case or terminals, allowing batteries to be positioned on their side.
Excellent recovery from deep discharge.
Low self discharge – approx 3% per month.
Not restricted for air transport – complies with IATA ICAO special provision A67.
Impact resistant ABS case and cover.
Industry standard footprints for easy field replacement
Maintenance free
98% recyclable
Charging: (25oC/77oF)
Standby use: Float charging voltage 13.50V to 13.80V.
Cyclic use: Maximum charging current 60A. Charging voltage: 14.4 - 14.7V.
Top charge: Product in storage (ambient temperature) required a top charge every 6 months. Apply constant voltage at 2.40 volts per cell, initial charging current should be set at less than 0.1 CA for 15 to 20 hours
At the same physical size as a 250W panel, the Q CELLS 305W Mono with Black Frame is a perfect high output module for roofs where space is limited and is available now at a very cost effective price.
The new high-performance module Q.PEAK-G4.1 is the ideal solution for residential buildings thanks to its innovative cell technology Q.ANTUM. The world-record cell design was developed to achieve the best performance under real conditions – even with low radiation intensity and on clear, hot summer days.
Specifications:
Peak power Wp 305W
Voltage at peak power Vmp: 32.62V
Max open circuit voltage Voc: 40.05V
Current at peak power Imp: 9.35A
Max short circuit current Isc: 9.84A
Weight: 18.8kg
Frame: Black Aluminium
Dimensions: 1670 x 1000 x 32mm
Warranty on output: 25 years
Product warranty: 12 years
Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel.
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
Delivery from £27.50
First panel £27.50, each additional panel just £6.50 delivery
ie: 3 panels costs £40.50 delivery.
Delivery service is an economy service that hand delivers fragile items on a weekly round across the UK.
Surcharge for remote areas including parts of Wales, Scotland, Ireland and Isle of Wight, please see Delivery info
This is a safer more reliable and cheaper way for you to receive panels and saves on the huge amounts of wasted packing materials.
Pallet Shipping 32 panels per pallet:
£175 UK Mainland
£375 Rest of Europe
Or you can collect for FREE from Nr Brighton.
30A MPPT
For 12V Solar System: 390W solar panel (150V for max input voltage)
For 24V Solar System: 780W solar panel (150V for max input voltage)
No Fan for silent operation, great for vans, boats or any live in spaces
New updated model with better communications and ability to fully program charge voltages via Optional PC cable or Optional MT50 Meter
The BN tracer models have a current limiting function, you can connect twice the rated power to the controller so if your on a budget you can use a smaller controller with more panels so that you get more power in winter or low light but don't risk overloading the controller in the summer. The output will be limited to the max listed above.
The Tracer BN is identical to the OutBack FLEXmax Micro Series, they are made in the same factory, showing outback's faith in this MPPT manufacturer.
New Tracer series is EPsolar’s second generation of MPPT controller. Compared with CLASSIC Tracer series, it has extensive communication ability. And the die-cast aluminium design ensures excellent heat dispersion.
Compared to conventional PWM controller, MPPT technology increases the charge efficiency up to 30% and potentially decrease the power of solar array needed.
Features:
·Innovative MPPT technology
·Peak conversion efficiency of 98%
·High tracking efficiency up to 99%
·Several seconds tracking speed
·Die-cast aluminium design and nature cooling
·Temperature compensation
·Diversified load control to meet different requirements
·Four battery type options: Sealed, Gel, Flooded, and USER
·Intelligent lighting and timer control for solar lighting system
·Energy statistics function
·RS485 ports with MODBUS communication protocol
·Optional PC monitoring software and remote meter for real-time monitoring and battery management parameter setting
·Field upgradable firmware
Electronic Protections:
·PV short circuit protection
·PV overvoltage alarm protection
·PV current limiting protection
·PV reverse polarity protection
·Battery overcharge protection
·Battery over discharge protection
·Battery reverse polarity protection
·Load overload protection
·Load short circuit protection
·Overheating protection
Model |
Tracer1215BN |
Tracer2215BN |
Tracer3215BN |
Tracer4215BN |
Nominal system voltage |
12/24V auto work |
|||
Rated battery current |
10A |
20A |
30A |
40A |
Rated load current |
10A |
20A |
20A |
20A |
Max. PV open circuit voltage |
150V |
|||
Max. battery voltage |
32V |
|||
Max. PV input power |
130W (12V) |
260W (12V) |
390W (12V) |
520W (12V) |
260W (24V) |
520W (24V) |
780W (24V) |
1040W (24V) |
|
Equalize charging voltage |
Sealed: 14.6V, Flooded: 14.8V, USER: 9~17V |
|||
Boost charging voltage |
Gel: 14.2V, Sealed: 14.4V, Flooded: 14.6V, USER: 9~17V |
|||
Float charging voltage |
Gel /Sealed /Flooded: 13.8V, USER: 9~17V |
|||
Low voltage reconnect voltage |
Gel /Sealed /Flooded: 12.6V, USER: 9~17V |
|||
Low voltage disconnect voltage |
Gel /Sealed /Flooded: 11.1V, USER: 9~17V |
|||
Self-consumption |
≤50mA(12V) ≤27mA(24V) |
|||
Grounding |
Common negative |
|||
Temp. compensation |
-3mV/℃/2V |
|||
Communication Port |
RS485 / RJ45 interface |
|||
Working temperature |
-35℃~+55℃ |
|||
Storage temperature |
-35℃~+80℃ |
|||
Humidity |
≤95% N.C. |
|||
Enclosure |
IP30 |
|||
Overall dimension |
196x118x36mm |
217x143x56mm |
281x160x60mm |
303x183x64mm |
Terminal |
4mm2 |
10mm2 |
16mm2 |
25mm2 |
Net weight |
0.9kg |
1.5kg |
2.3kg |
2.9kg |
Pure sinewave output, high peak power and high efficiency. Combined high frequency and line frequency technologies ensure the best of both worlds. Models range from 150VA to 3000VA per module.
VE.Direct allows use with VE.Direct Bluetooth adaptor to control the inverter via your phone or laptop.
Spec Sheet
Optional Meter for AN BN & CN Tracer MPPT charge controllers (10A, 20A, 30A or 40A) for CN controllers need specialist cable cable available on our site
PLEASE NOTE - YOU CANNOT USE THE MT50 AT THE SAME TIME AS THE BLUETOOTH / WIFI OPTIONAL ADAPTORS
Features:
·Automatic identify the controller, and display the type, model and relevant parameter data
·Large-screen multifunction LCD displays all the operational data and system working status in digital, graphic and textual forms
·With six navigation function keys, the operation is direct, convenient and rapid
·Real-time energy statistics recording
·Both data and data flowing on the same lead ,no need for external power
·Real-time monitoring and acoustic alarm of failure information of the controller
·Longer communication distance based on RS485
Functions Via MT50
·Diversified load control modes : manual, light ON/OFF, Light ON+ Timer, Time Control
·Battery type selection: Gel, sealed, flooded and USER type
·Real-time monitor
·Programmable parameters
·Energy display function
Download Guide to change language
Self-consumption |
Backlight and acoustic alarm on<65mA Backlight on<23mA Backlight off <15mA |
Faceplate dimensions |
98×98 mm / 3.86×3.86 in |
Frame dimensions |
114×114 mm / 4.49×4.49 in |
Connector type |
RJ45 |
Meter cable |
Standard 2m, max .50m |
Meter weight |
0.190 Kg |
Ambient Temperature |
-20℃~+70℃/-4℉~158℉ |
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
10mm cable - Charge Controller to Batteries - 2 Meter with M8 Lug
You will need 2 cables per charge controler (Pos & Neg). The Lugs are on 1 end only as the charge controllers have bare wire connectors.
If you need longer please let us know
Battery Inter-connecting Cable - 35mm cable with M8 - M8 Lugs (M8 on both ends)
Made up to size for you for connecting your batteries together.
6mm Solar Cable - Price is per meter simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable
Max load: 50A
MC4 Solar Connector - Price is per MC4 pair simply select the quantity as the number of MC4 pairs you want.
These are the standard connectors used on most solar panels.
TUV certified, brand new, water /weather proof rubber seal that can ensure excellent electrical contact for life time service.
The metal pin is made from high quality machined copper and sealed tip (compare to the cheap sheet metal pin) that can ensure excellent electrical contact for life time service.
Build in press tabs for easy disconnect, no tool is needed. 25A max load.
Wires should be crimped or soldered into the pins and care should be taken to get the correct pin into the correct connector. Once the pin is pushed into the connector it is difficult to remove without the correct tooling.
MC4 Main Technical Specification:
Maximum Current: 25A
Maximum voltage: 1000V
Contact resistance:≤5mmΩ
Maximum operating humidity: 5% -95% (No condensation)
Temperature: -40 ℃ ~ +90 ℃
Waterproof Grade: IP67
Flame class: UL94-V0
Connecting cable specifications: 2.5mm2 4mm2 6mm2
Test voltage: 6.6KV (50Hz, 1min)
Metal materials: nickel copper
Insulation material: PA12 * 1988HB
Lock mode: Self-locking
Security Level: Class ‖
Insertion force:≤50N
Withdrawal force:≥50N
MC4 Features:
Shell has a strong anti-aging, anti- UV capability; found in outdoor use under harsh environment requirements; according to different needs can be arbitrary and used in conjunction with a variety of cell junction box; all connections are using press-fit connection;