Note - Victron 100 20 SmartSolar has 290w output limit, can handle 350w PV input - in UK conditions 350w PV rarely will supply more than 290w, so there is a good saving in ££ to use this controller, which is why it is in this kit. If you would rather the 30a version you can swap for this, we would only recommend this for European use with better solar production.
• Low voltage-temperature coefficient enhances high temperature operation.
• Exceptional low light performance and high sensitivity to light across the entire solar spectrum.
• 25 - Year limited warranty on power output and performance.
• 5 - Year Limited warranty on materials and workmanship.
• Sealed, waterproof, multi-functional junction box gives high level of safety.
• High performance bypass diodes minimise the power drop caused by shade.
• Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation.
• A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems.
• Highest quality, high transmission tempered glass provides enhanced stiffness and impact resistance.
• Pre wired quick connect system with PV-ST01 connectors.
MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.
Long Aluminium Mounting Brackets - Stick down on Boats - Rivet down on vans
Use one pair for up to 100w panels and 2 pairs larger panels
Foot print (550mm long, 75mm wide)
Rivet plate 25mm
Panel ledge 30mm
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 10m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 50A
Contacts: Copper.Tin plated
Degree of protection: IP67
Flame class: UL94-V0
Wire size range: 6mm2
STÄUBLI MC4 Solar PV connectors - Pair of Y Branches
Connect your solar modules together with ease using these safe and durable MC4 connectors. This pair of "Y" shape connectors (one in a male to female, female configuration, and one in a female to male, male configuration) will allow you to connect panels or strings of panels together. If you need to connect 3 panels together then it is cheaper to use 2 pairs of these than to purchase a 3 way splitter (its about 1/3 of the cost to use these)
|Connector system||Ø 4 mm|
|Rated voltage||1500 V DC (UL)|
|Rated current||50 A|
|Rated impulse voltage||12 kV|
|Ambient temperature range||-40 °C...+75 °C (UL)|
|Upper limiting temperature||105 °C (Stäubli)|
|Degree of protection, mated unmated||IP67 IP2X|
|Overvoltage category/Pollution degree||CATIII / 2|
|Contact resistance of plug connectors||≤0.5 mΩ|
|Contact material||Copper, tin plated|
|Locking system (UL)||Locking type|
|UL recognized component, in accordance with UL 6703||E343181|
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.
Cable Gland Entry Box, use to connect through external surface. Perfect for solar panel cables coming from outside to controller.
A small, low cost multimeter supplied with test leads, perfect to help you setup and test your solar installation.
DMM Functions: DC Current, AC/DC Voltage, Diode, Resistance
No. of Digits: 3.5
DMM Response Type: Average
Display Count: 1999
Range Selection: Manual
Voltage Measure DC Max: 500V
Voltage Measure AC Max: 500V
Current Measure DC Max: 5A
Resistance Measure Max: 2Mohm
Simple DIN mount rail 10cm long for DC or AC DIN mount breakers. Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it. Quick easy and simple solution to install breakers to your solar system.
Use with our: