JA Solar 380W Mono MBB Percium Half-Cell Black Frame MC4 Dimensions: 1776 X 1052 X 35mm
Panels - Monocrystallines
JA Solar Large Wafer PERC Mono Half-Cell Multi Bus Bar Module.
This module has Black Frame and White Backsheet.
New XTRA series - 3rd Generation MPPT
For 12V Solar System: 390W solar panel (150V for max input voltage)
For 24V Solar System: 780W solar panel (150V for max input voltage)
No Fan for silent operation, great for vans, boats or any live in spaces
With built in LCD advanced display and programming screen (XDS2)
New XTRA series has Lithium battery support (set via PC cable only)
The XTRA tracer models have a current limiting function, you can connect twice the rated power to the controller so if your on a budget you can use a smaller controller with more panels so that you get more power in winter or low light but don't risk overloading the controller in the summer. The output will be limited to the max listed above.
New EPEver (Tracer) series is EPsolar’s third generation of MPPT controller.
XTRA series are advanced maximum power point tracking (MPPT) charge controllers, for off grid photovoltaic systems, with display unit.
In order to maximise the energy harvest from PV arrays and simultaneously minimise the power loss within a wide range of operating conditions, XTRA series apply an advanced smart algorithm which results in up to 30% higher efficient charging, compared to a conventional pulse width modulation (PWM) charge controller. Xtra series controller have limit protection function on charging current &charging power, as well as auto derating power operation at high temperature; the above protection ensure the stability of system even at exceeded rated PV power and over temperature conditions.
Protection class IP32 and isolated RS485 communication port further improve the controller’s reliability under different application requirements. XTRA series controllers incorporate a self-adaptive three-stage charging algorithm based on a digital control circuit, which eeffectively prolongs the lifespan of battery and significantly improve the system performance. It also has extensive electronic protection for overcharge, over discharge, PV&battery reverse polarity and etc. to ensure the sustainability and durability of the o-grid solar system.
¹ If using Lithium battery, customer should use “PCsoftware” to set the lithium battery parameters
² Ingress of solid objects:Protected against solid objects over 2.5mm
² Ingress of liquids: Protected against falling drops of water, if the case is disposed up to 15 from vertical
A pair of 2mm stainless steel (316L) solar panel brackets designed with canalboats and vehicles in mind, supplied with marine standard cable glands and anti tamper bolts & bit.
Allow your solar panels to both tilt and swivel throughout the year, maximising the sun's energy whilst providing excellent ventilation. This can improve the power of your panels by up to 40%, perfect for smaller systems where efficiency is key. *Standing at just over 25cm high and 16cm wide they're designed to maximise the angle of your panels whilst being low enough for most bridges and tunnels.
Using any padlock attach your panel securely to the roof via an integrated 8mm stainless steel chain that secures directly to the bracket, keeping your panels safe. The anti tamper bolts secure the bracket to your roof for maximum security deterring even the most determined of thieves.
Using M10 for both bolts and glands means you only need to drill six identical holes, saving both time and money on tools or labour whilst providing a safe and secure mounting solution.
A tool kit with everything you need for a waterproof and secure installation supplied separately, select the tool kit option to purchase this as well.
2 top spec cobalt drill bits and M10 tap and ratchet allow quick and easy installation with even the toughest steel roof.
Supplied with marine sealant, a secure and waterproof installation can be done in as little as 4 hours.
Save yourself hours of drilling! Get our essential toolkit for installing the boat swivel mounts!
Cobalt drill bits (for drilling into the panel frame and boat hull) 8.5mm and 5.5mm
Ratchet and Tap set (Taper, Plug & Bottoming)
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 10m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Class 5 flexible tinned copper conductor
Halogen-free cross-linked compound
Halogen-free cross-linked, flame retardant compound
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Optional Meter for AN, BN, CN, XTRA MPPT charge controllers. DuoRacer requires the MT11, see separate listings.
Comes with 2m RJ45 cable in the box, if you need longer we have a 5m cable here 5m RJ45 Cable for MT50
PLEASE NOTE - YOU CANNOT USE THE MT50 AT THE SAME TIME AS THE BLUETOOTH / WIFI OPTIONAL ADAPTORS
·Automatic identify the controller, and display the type, model and relevant parameter data
·Large-screen multifunction LCD displays all the operational data and system working status in digital, graphic and textual forms
·With six navigation function keys, the operation is direct, convenient and rapid
·Real-time energy statistics recording
·Both data and data flowing on the same lead ,no need for external power
·Real-time monitoring and acoustic alarm of failure information of the controller
·Longer communication distance based on RS485
Functions Via MT50
·Diversified load control modes : manual, light ON/OFF, Light ON+ Timer, Time Control
·Battery type selection: Gel, sealed, flooded and USER type
·Energy display function
Backlight and acoustic alarm on<65mA
Backlight off <15mA
98×98 mm / 3.86×3.86 in
114×114 mm / 4.49×4.49 in
Standard 2m, max .50m
Please note: Older MT50s manufactured before August 2017 are not compatible with the newer XTRA and AN controllers.
10mm cable - Charge Controller to Batteries - 2 Meter with M8 Lug
You will need 2 cables per charge controler (Pos & Neg). The Lugs are on 1 end only as the charge controllers have bare wire connectors.
If you need longer please let us know
Cable Gland Entry Box, use to connect through external surface. Perfect for solar panel cables coming from outside to controller.
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.
A small, low cost multimeter supplied with test leads, perfect to help you setup and test your solar installation.
DMM Functions: DC Current, AC/DC Voltage, Diode, Resistance
No. of Digits: 3.5
DMM Response Type: Average
Display Count: 1999
Range Selection: Manual
Voltage Measure DC Max: 500V
Voltage Measure AC Max: 500V
Current Measure DC Max: 5A
Resistance Measure Max: 2Mohm
Simple DIN mount rail 10cm long for DC or AC DIN mount breakers. Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it. Quick easy and simple solution to install breakers to your solar system.
Use with our: