Victron Smart Solar 20A MPPT charge controller with max VOC 100V for 12V, 24V or 48V battery systems.

MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

Load output
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.

Download full spec sheet

325W JA Solar Panels Mono Percium - All Black Half Cell, 1689 X 996 X 35mm

Half Cell Advantages

• High output power
• Less shading effect
• lower temperature coefficient
• Better mechanical loading tolerance

Supplied with 1000mm output cables and QC4.10 connectors (connects to MC4s)

Percium Cell
The latest in mono cell technology with passivated backside, local BSF and 4 Bus Bars from worldwide PV Cell leaders - JA Solar
First to reach >20.6% average cell efficiency in mass production
 
More Power Per m²
JA higher efficiency module type specially designed for UK rooftop market.
Maximise the kWp installation on the roof 
 
Aesthetics
Homogeneous Black Mono cells.
Black Frame for anti-glare and pleasing appearance.
 
Lower System Cost
Reduced installation and BOS cost
 
Excellent Low-light Performance
Enhanced spectral response at longer wavelength boosts low-light performance, which can produce more than 1% additional power compared with conventional module at system side.
 
High Reliability
Passed "3xMCS" TÜV SÜD Thresher Long life Accelerated Stress Tests.
Full range of PID-resistance tests
Harsh climate environment endurance tests
Full set of long-term reliability tests
Manufacturing inspected and certified by leading institutes such as PI-Berlin, Franhoeffer, Sgurr, OST and Solar-IF
100% in-house automatic manufacturing
2X 100% EL inspection ensuring defect-free production
Over 500MWp of JA Solar panels installed in the UK. 10GWp Worldwide.
 
Other Features
Positive power tolerance: -0~+5W
Modules binned by current to improve system performance
Excellent mechanical load resistance: Certified to withstand high wind loads (2400Pa) and snow loads (5400Pa)

Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel. 

This listing is for 1 panel, simply select how many you need in the quantity.  There is NO MINIMIUM Order.

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Set of 4 Aluminium mounting brackets for mounting solar panels on vans, boats, sheds or a wooden frame as a easy cheap solar framing system.

** Panels larger than 100w are not recommended to use these alone, as a direct fixing to a vehicle roof.  We suggest a bespoke solution using bolts, some of our customers use these brackets and modify them to achieve this, others get a locally fabricated solution **

Includes:
Aluminium mounting brackets;
Wood screws:St5.7 mm*30mm,
Socket Head Screw:M6*25mm,

Cable Gland Entry Box, use to connect through external surface.  Perfect for solar panel cables coming from outside to controller.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

A small, low cost multimeter supplied with test leads, perfect to help you setup and test your solar installation.

• AC/DC voltage measurement
• DC current
• Resistance measurement (20R to 2MR)
• Diode and transistor tester
• Low battery indication
• Requires a 9V PP3 battery

DMM Functions: DC Current, AC/DC Voltage, Diode, Resistance  
No. of Digits: 3.5  
DMM Response Type: Average  
Display Count: 1999  
Range Selection: Manual  
Voltage Measure DC Max: 500V  
Voltage Measure AC Max: 500V  
Current Measure DC Max: 5A  
Resistance Measure Max: 2Mohm  
 

Simple DIN mount rail 10cm long for DC or AC DIN mount breakers.  Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it.  Quick easy and simple solution to install breakers to your solar system.

Use with our:

• DC DIN mount breakers
• RCBO AC breakers.