Highly efficient module giving 365W from a 1.7m panel, great if you have limited space. 1700 X 1016 X 40mm

Better in low light than standard panels

LG NeON™2 365Wp solar PV module with black frame, features high efficiency 60 x LG NeON™ 2 monocrystalline cells. The LG NeON™ 2 has been designed to significantly enhance its output efficiency making it efficient even on limited roof areas.

LG NeON™ 2 has an enhanced performance warranty. The annual degradation has fallen from -0.7%/yr to -0.6%/yr. Even after 25 years, the cell guarantees 2.4%p more output than the previous NeON™modules.

The LG NeON™ 2 has been designed with aesthetics in mind; thinner wires that appear all black at a distance. LG NeON™ 2 now performs better on sunny days thanks to its improved temperature co-efficiency.

With its newly reinforced frame design, LG has extended the warranty of the NeON™ 2 for an additional 2 years. Additionally, LG NeON™2 can endure a front load up to 6000 Pa, and a rear load up to 5400 Pa.

Module dimensions: 1700 x 1016 x 40mm

• High module efficiency of 20.4%
• Connector Type: MC4, MC4 Compatible
• IP67

30A MPPT with max VOC 100V, 12 or 24 Volt battery

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

A pair of 2mm stainless steel (316L) solar panel brackets designed with canalboats and vehicles in mind, supplied with marine standard cable glands and anti tamper bolts & bit. 

Allow your solar panels to both tilt and swivel throughout the year, maximising the sun's energy whilst providing excellent ventilation. This can improve the power of your panels by up to 40%, perfect for smaller systems where efficiency is key. *Standing at just over 25cm high and 16cm  wide they're designed to maximise the angle of your panels whilst being low enough for most bridges and tunnels. 

Using any padlock attach your panel securely to the roof via an integrated 8mm stainless steel chain that secures directly to the bracket, keeping your panels safe. The anti tamper bolts secure the bracket to your roof for maximum security deterring even the most determined of thieves.

Using M10 for both bolts and glands means you only need to drill six identical holes, saving both time and money on tools or labour whilst providing a safe and secure mounting solution. 

Tool Kit

A tool kit with everything you need for a waterproof and secure installation supplied separately, select the tool kit option to purchase this as well.

2 top spec cobalt drill bits and M10 tap and ratchet allow quick and easy installation with even the toughest steel roof. Supplied with marine sealant and instructions, a secure and waterproof installation can be done in as little as 4 hours.  

Click here for Technical Spec Sheet

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 15m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Save yourself hours of drilling!  Get our essential toolkit for installing the boat swivel mounts!

Contains:

Cobalt drill bits (for drilling into the panel frame and boat hull) 8.5mm and 5.5mm

Ratchet and Tap set (Taper, Plug & Bottoming)

Marine Sealant

10mm cable - Charge Controller to Batteries - 2 Meter with M8 Lug

You will need 2 cables per charge controler (Pos & Neg).  The Lugs are on 1 end only as the charge controllers have bare wire connectors.

If you need longer please let us know

The SE7 side-entry twin cable gland is the perfect solution when space is limited or when loops from conventional top entry glands are not appropriate. Available in various finishes, the entire SE series of glands are tested achieving the IP68 rating which ensures a perfect waterproof solution for various cable management applications.  Each unit is supplied with clear fitting instructions and A4 stainless steel fixings. Suitable for two cables 3 – 6mm diameter supplied with tapered seals which ensure that the hole closes completely, creating a watertight seal around the cable. Ideal for electrical cabling applications and ducting through bulkheads, decks, and panels – i.e. VHF, Satnav, GPS and Radar installations.

Waterproof / dustproof (to IP68) gland with parallel low profile cable entry. Cable Size: 2 x 3mm – 2 x 6mm (3 pre-moulded bungs, no drilling required)

Designed for the Marine industry – IP68 for all applications

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

A small, low cost multimeter supplied with test leads, perfect to help you setup and test your solar installation.

• AC/DC voltage measurement
• DC current
• Resistance measurement (20R to 2MR)
• Diode and transistor tester
• Low battery indication
• Requires a 9V PP3 battery

DMM Functions: DC Current, AC/DC Voltage, Diode, Resistance  
No. of Digits: 3.5  
DMM Response Type: Average  
Display Count: 1999  
Range Selection: Manual  
Voltage Measure DC Max: 500V  
Voltage Measure AC Max: 500V  
Current Measure DC Max: 5A  
Resistance Measure Max: 2Mohm  
 

Simple DIN mount rail 10cm long for DC or AC DIN mount breakers.  Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it.  Quick easy and simple solution to install breakers to your solar system.

Use with our:

• DC DIN mount breakers
• RCBO AC breakers.