Pylon US5000 4.8kWh Li-Ion Solar Battery 48V (excl. brackets)

A new battery in the US series from Pylontech. The US5000 is a 48V battery with incredible features to provide a competitive edge in the market. 

Product Features

• Modular design for ease of expansion
• Higher usable capacity resulting in less battery modules installed
• Usable capacity 4 560Wh
• Parallel Capability of up to 16 units
• Allows for large installation of up to 72.96kWh with no LV Hub
• Intelligent BMS protecting battery cells
• 95% DoD with more usable capacity
• RS485 and CAN compatible
• Comes with a 5-year warranty extendable
• Long cycle life and superior performance
• Compatible with tier 1 inverter brands
   

If you want to use these batteries with Victron equipment please read this article to select the correct equipment:

https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
 

Here is the link to register your batteries and receive extended warranty:

https://en.pylontech.com.cn/service/support/

ENA approval for grid connection of this unit is now available

All-in-one solar power solution, 4000W inverter, 250/100 MPPT charge controller

The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.

The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.

Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.

Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
MultiPlus-II inverter/charger.
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.

GX device
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.

FOR LARGE PANEL DELIVERY TIMES, SCHEDULES AND COSTS - CLICK HERE

Super High Efficiency Mono PERC Module (CS6R-410MS)   Dimensions: 1722 X 1134 X 30mm

Cables from rear junction box are approx 1m positive and 1m negative.

CANADIAN SOLAR INC.is committed to providing high quality solar products, solar system solutions and services to customers around the world. As a leading PV project developer and manufacturer of solar modules with about 30 GW deployed around the world since 2001, Canadian Solar Inc. is one of the most bankable solar companies worldwide.

With proprietary mono wafer and cell technologies Canadian Solar have developed an extraordinary module rage. Combining the best technology and design, it also reduces LCOE and installation costs.

The Super High HiKu mono modules with dimensions of 1722 X 1134 X 30mm, have the following unique features:

MORE RELIABLE (THANKS TO HALF CUT CELL TECHNOLOGY):

• Lower internal current, lower hot spot temperature
• Cell crack risk limited to smaller area of the cell
• Innovative symmetrical module design means better shading tolerance
• Heavy snow load up to 5400Pa and increased wind load up to 3600Pa

Cell: 120 x dual-cell Mono, 156 x 78 mm

Dimensions: 1722 X 1134 X 30mm

Weight: 21.3 kg

A modular heavy duty DC bus bar with locations for four DC fuses. It has a positive and negative bus bar.  The Lynx distributor can link (piggy back) onto each other to form a larger bus bar for a variety of applications. For use stand alone or with the Lynx modular system, see manual under the downloads tab.

It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar https://www.bimblesolar.com/Victron-lynx-powerin

6mm² Solar Cable - Price is for a 100 meter reel. If you wish to buy in lower quantity meter lengths, please see https://www.bimblesolar.com/6mmcable

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Other colours available on request if bulk order

A set of battery brackets which allows vertical stacking of the Pylon US5000 battery unit. 1 set required per battery.

Victron MK3-USB Configuration Interface

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.

Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.

Supported Platforms

The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.

Description

This industrial quality Multi-Contact tool is a first priority for Crimping MC4 male and female solar contacts, used for the cable(2.5/4/6 mm2)
The excellent handling, easy exchange of the crimping insert bits and the possibility of adding a positioning aid are facts in favour of these crimping pliers.

•     High-precision ratchet mechanism for crimps
•     1.2 metric tons pressure at crimping face, with minimal hand effort;
•     Interchangeable high-precision crimping die set

Tools Parameters
    Capacity: 2.5-6.0mm2
    AWG: 26-10AWG
    Length: 270mm
    Weight: 0.74Kg

This outdoor rated combiner box is for safely combining larger strings of solar panels >= 3. The box comes fitted with Din rail and 10 X M20 glands with a cable outer diameter range of 5 - 10mm.

The enclosure features knock out discs so no drilling is required. Just punch out the number if gland spaces required, and fit the glands. You must select the fuse holder, fuses, bus bar, feeder terminal and extra glands if required for your system.  See related items tab above to see the breakers that fit. If fusing positive conductors only, select Din rail block to combine the negatives. It is possible to mount he box without puncturing it thus maintaining the IP waterproof rating

Outside dimensions: 182 X 180 X 111mm

Inside dimensions: 167 X 165 X 96mm

Effective Din rail length: 150mm

Number of gland knock outs: 8 X M20, 1 X M25 or M32 (top & bottom), 4 X M20, 1 X M32 or M40 (left side and right side)

Mechanical Hexagonal crimp tool for 10mm² -120mm² copper tube terminal lugs. For manual crimping of terminal lugs and pin ferrules onto battery cable. 45cm long handles.

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.

The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.

NH00 rated at  250VDC, 160A,

Choose NH00 or NH000 fuses separately

Product measures 170mm H X 84mm W X 80mm D. Surface mountable.

Battery Switch ON/OFF 275A

The Battery Switch ON/OFF 275A is suitable for battery systems up to 48V. It has a unique ergonomic and aesthetic knob design. The knob is removable for isolation or safety purposes.

The Battery Switch can be either surface or panel mounted, providing flexibility during install.

The Battery Switch meets the ISO8846 Ignition Protection standard and is suitable for use in an engine room.

10mm tinned copper Solar Cable - Price is per meter simply select the quantity as the number of meters you want.

Double Insulated UV protected solar cable, 6.9mm Outer Diameter, Halogen-free cross-linked

Max load: 98A

European standard solar cable intended for the interconnection within photovoltaic systems such as solar panel arrays. Suitable for fixed installations, internal and external, within conduit or systems, but not direct burial applications. Our solar cable is ozoneresistant according to BS EN 50396, UV resistant according to HD 605 S2 and is tested for durability according to EN 60216.

One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.

Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off  the supply to a solar charge controller or solar inverter.

Choose fuse separately

Item dimensions 75mm H X 16mm W X 55mm D

200A Fuse for 48V systems

For use with Mega Fuse Holder

STÄUBLI MC4 Solar PV connectors - Pair 

Connect your solar modules together with ease using these safe and durable genuine Staubli MC4 connectors. Snap-in lock. MC4 crimp tool required to make onto cable ends. YOUTUBE VIDEO

Manufacturer SKU
32.0016P0001-UR & 32.0017P0001-UR

See DOWNLOADS TAB for datasheet

 Technical specifications

*Please note male and female refers ot the metal conductor and not the plastic insulator*

Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line

Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.

The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.

This item fits String Fuse holder

• Complies to ISO 20934
• Cu alloy element
• Tin plated integrated heatsink
• Riveted PPA GF35 thermoplastic colour coded housing
• Colour coded housing with value in OCR font on both sides

ELECTRICAL & SPECIFICATIONS
Input Voltage 70V DC Maximum
Breaking capacity 2500A at 70VDC
Dimensions 68mm x 19mm x 10.5mm
Hole size M8
Hole centres 50.9mm
Maximum torque 12Nm ± 1 Nm
Identification Colour coded housing and value in OCR font on both sides

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for Pylontech C series batteries and BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.

NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC

Copper busbar for parallel our solar string fuse holders or the Tomzn DC breaker <63A in the solar combiner box to take a single feed to a charge controller for example.

10 mm², 17.5mm partition (distance between centre of poles), peg design, L-shaped bar. The busbar comes with a plastic cover. Cut the busbar down to the number of poles required for your application. Use the feeder to take a single feed from the bus bar.  Made in Germany

Din rail mountable junction block for joining conductors of like polarity. Can be use for joining/combining the negative conductors in our PV combiner boxes. M6 terminal lugs required separately. Additional M6 nuts and washers recommended if stacking multiple terminals on the M6 posts.

Use the feeder terminal to take a single feed from the bus bar in the solar combiner box to a solar charge controller for example. The feeder terminal accepts from 6 - 25mm² cable and the pin length is 15mm. Consider using a ferrule or flat pin lug on the end of the cable go into the female end of the terminal.  Made in Germany

25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK 

Bag of 10 x 6mm Ring Yellow Crimps - 48A max current.

for 4mm or 6mm cable

10mm squared cable end lug for crimping onto 10mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK