Victron Smart Solar 50A MPPT Solar Charge Controller with max VOC 100V, 12 or 24 Volt battery

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

SPR-P6-400-BLK

From the World's leading Solar Panel Manufacturer...

Enhanced Power Density
With high efficiency, LID-resistant solar cells (G12, 210mm), a lower temperature coefficient, and front-side conductive wires that support increased current collection, SunPower Performance panels are uniquely engineered to deliver more lifetime energy over standard solar panels.
 

Proven Reliability
A proprietary shingled-cell design maximises durability in all types of weather conditions—including reinforced cell connections that withstand the stresses of daily temperature swings, redundant electrical paths that alleviate the impact of cell cracks, and an advanced electrical architecture that is more resilient to the effects of shade and mitigates hot-spot formation.

Note - In unusually high winds, you should flat mount your panels 

SEE ESSENTIAL TOOLKIT LINK BELOW, PURCHASE IF YOUR INSTALLER DOES NOT HAVE THESE PARTS AS REQUIRED TO FIT:

TOOLKIT LINK HERE

Tool Kit

A tool kit with everything you need for a waterproof and secure installation supplied separately, select the tool kit option to purchase this as well.

2 top spec cobalt drill bits and M10 tap and ratchet allow quick and easy installation with even the toughest steel roof.

Supplied with marine sealant, a secure and waterproof installation can be done in as little as 4 hours.  

----

Boat Solar Panel Tilting Mounting Bundle - Stainless Steel Swivel Brackets

A pair of 2mm stainless steel (316L) solar panel brackets designed with canalboats and vehicles in mind, supplied with anti tamper bolts & bit. 

Allow your solar panels to both tilt and swivel throughout the year, maximising the sun's energy whilst providing excellent ventilation. This can improve the power of your panels by up to 40%, perfect for smaller systems where efficiency is key. *Standing at just over 25cm high and 16cm  wide they're designed to maximise the angle of your panels whilst being low enough for most bridges and tunnels. 

Using any padlock attach your panel securely to the roof via an integrated 8mm stainless steel chain that secures directly to the bracket, keeping your panels safe. The anti tamper bolts secure the bracket to your roof for maximum security deterring even the most determined of thieves.

Using M10 for both bolts and glands means you only need to drill six identical holes, saving both time and money on tools or labour whilst providing a safe and secure mounting solution. 

Contents:

1 x Stainless Steel Bracket with Chain

1 x Stainless Steel Bracket with no chain

4 x TORX Security bolts

2 x Hand Spindles

2 x Stainless Steel Wingnuts

2 x Stainless Steel Spring Washers

2 x Stainless Steel Washers

1 x TORX Security bit

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 15m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Save yourself hours of drilling!  Get our essential toolkit for installing the boat swivel mounts!

Contains:

Cobalt drill bits (for drilling into the panel frame and boat hull) 8.5mm and 5.5mm

Ratchet and Tap set (Taper, Plug & Bottoming)

Marine Sealant

4 Way unit can hold our Tomzn DC and AC breakers

 Unit can hold the following options:

• 2 x AC RCBos
• 4 x DC breakers Under 60A
• 2 x DC breakers 80A - 125A

This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.

One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.

Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off  the supply to a solar charge controller or solar inverter.

Choose fuse separately

Item dimensions 75mm H X 16mm W X 55mm D

Cable Gland Entry Box, use to connect through external surface.  Perfect for solar panel cables coming from outside to controller.

This comes with a cradle for keeping your MC4 connectors in place and tidy.

Dimensions:

Length 182mm

Width 95mm

Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line

Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.

The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.

This item fits String Fuse holder

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

This breaker can take up to and including 25mm2 cable.

A small, low cost multimeter supplied with test leads and holster.

• 3½ digit, 1999 count display
• AC/DC voltage measurement
• DC current
• Resistance measurement (20R to 2MR)
• Diode, continuity and transistor tester
• Square wave output
• Low battery indication
• Requires a 9V PP3 battery (included)

DMM Functions: DC Current, AC/DC Voltage, Continuity, Diode, Resistance, Transistor
No. of Digits: 3.5  
DMM Response Type: Average  
Display Count: 1999  
Range Selection: Manual  
Voltage Measure DC Max: 500V  
Voltage Measure AC Max: 500V  
Current Measure DC Max: 5A  
Resistance Measure Max: 2Mohm