For Victron and Pylontech systems, please check the following manual link
The Pylontech US3000C has an incredible DoD of 95%.
Please use a dimension of 3U per module when sizing a cabinet for these batteries.
Advantages
You can now register the Pylon US3000C for an additional 3 years of manufacturer warranty for free. Go to Pylon Support and complete the information in the 'sign up battery' page.
The US3000C can be used to expand an existing US3000 bank. Please note, the US3000C needs to be used as the master battery when used to expand an existing US3000 bank.
DIP switch has been deployed reversely. ON is down, OFF is UP. If DIP switches need to be 1000 then set it to 1110. MAX DISCHARGE AND CHARGE RATE IS ONLY APPLICABLE FOR +- 60 SECONDS
If using this battery with Victron equipment it requires a Type A communications cable to the Victron GX device not a Type B.
You can optionally add mounting brackets BRACK-US3000 to this product for a stable base, and to allow easy stacking of multiple units.
If you want to use these batteries with Victron equipment please read this article to select the correct equipment:
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
Here is the link to register your batteries and receive extended warranty:
The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.
The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.
Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.
Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
MultiPlus-II inverter/charger.
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.
GX device
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.
A set of battery brackets which allows vertical stacking of the Pylon US3000 battery unit. 1 set required per battery.
Mechanical Hexagonal crimp tool for 10mm² -120mm² copper tube terminal lugs. For manual crimping of terminal lugs and pin ferrules onto battery cable. 45cm long handles.
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 15m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Victron MK3-USB Configuration Interface
The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.
Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.
Supported Platforms
The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.
**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**
One pole fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or charge controller and battery. Integrated handle enabling use as an isolator.
NH00 rated at 250VDC, 160A
Choose NH00 or NH000 fuse separately
Item dimensions 170mm H X 42mm W X 80mm D
Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 2.5m lengths MC4 to bare wire)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Pylon battery cable accessory kit for use with all the different battery models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the inverter/charger.
Please check the number of cable packs you need, according to your inverter/charge specifications. Each cable pack is rated at 100A continuous, and 125A peak.
This cable pack includes the following cables:
2 x 2m long power cables (1x positive and 1x negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.
DC Switch
Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for Pylontech C series batteries and BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.
NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.
Fuses are rated at 250VDC
25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK