MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.
Bimble Solar 120W Mono Panel
120W power, great for smaller applications and lighting. These are 12V panels so you can use with PWM controllers to make a very cheap system.
Size: 860 x 700 x 25mm
MC4 ended premade solar cables are 60cm long each
We have packages for both off grid solar panel systems and on grid Installations. (see other listings)
As these are small panels we use standard couriers - delivery is cheaper.
Or you can collect for FREE from Near Brighton, East Sussex
Fixes without screwing holes in your roof!
ABS mounts raise the panel by 25mm. Edge of panel to edge of ABS is 55mm.
We sell CT1 which is great for sticking these down, please see related products tab for different colours avaialble.
If you are fitting to a vehicle we recommend that you additionally bolt or screw the panel and mounting down as well, as the strength of these systems is only as strong as the roof type or paint on your roof!
NOTE - You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method...
Here is a good tutorial to get you started:
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Class 5 flexible tinned copper conductor
Halogen-free cross-linked compound
Halogen-free cross-linked, flame retardant compound
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
3 Way unit can hold our Tomzn DC and AC breakers
Unit can hold the following options:
Best practice would be to use this unit with no bigger than 10mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit. If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.
This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.
You will also need suitable cable entry glands - please see related products tab.
|Product Depth||114 mm|
|Product Height||160 mm|
|Product Type||DIN Enclosure|
|Product Width||85 mm|
For use with our stick down panels and ABS mounting kits - also great for sealing cable holes
CT1 will successfully bond:
Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)
Cable Gland Entry Box, use to connect through external surface. Perfect for solar panel cables coming from outside to controller.
This comes with a cradle for keeping your MC4 connectors in place and tidy.
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.