TNE Series, TN’s most powerful products, are specially designed for deep cycle application. With numbers of national patent technologies, the cycle life reaches 400-600 cycles at 100% DOD, highly suitable for golf carts, electric wheelchairs, low-speed electric vehicles etc. Maintenance free technology reduce the complexity with water adding during use and become more and more popular in the market.

The all-in-one solar power solution

The Victron EasySolar-II GX integrates the following elements:

• A MultiPlus-II inverter/charger

• A SmartSolar MPPT -Tr solar charge controller

• A GX device with a 2 x 16-character display.

These elements come prewired together inside a single unit. This greatly simplifies most installations, saving time and money. Display and Wi-Fi The display reads battery, inverter and solar charge controller parameters. The same parameters can be accessed with a smartphone or other Wi-Fi enabled device. In addition, Wi-Fi can be used to set up the system and to change settings. Solar charge controller The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the MultiPlus-II inverter/charger. The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT. GX device

The integrated GX device includes:

• A BMS-Can interface. This can be used to connect to a compatible CAN-bus managed battery. Note that this not a VE.Can compatible port.

• A USB port

• An Ethernet port

• A VE.Direct port

The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a VE.Bus and a VE.Direct connection.

The manual is available here:

https://www.victronenergy.com/media/pg/EasySolar-II_GX/en/index-en.html

The datasheet is available here:

https://www.victronenergy.com/upload/documents/Datasheet-EasySolar-II-24V-48V-3kVA-48V-5kVA-MPPT-250-70-100-GX-EN.pdf

Caravan/campervan site extension lead with 15m cable 100% copper (3 core 2.5mm²)
Moulded IEC 60309 3-Pole 16amp/230V site connectors, specially designed to work with the Victron Stainless steel shore power inlet (see related products)

The Smart Battery Shunt

The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.

The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.
The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.

This unit has M10 bolts.

Power inlet for boat (shore power inlet), van, living vehicle or motorhome. 

16A. 250VAC

Solid Cast 316 Stainless Steel

Brass, Nickel plated pins

IP56 rating

This would require a hole making in the vehicle/vessel exterior as it is panel mounted (recessed)

Victron MK3-USB Configuration Interface

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.

Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.

Supported Platforms

The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.

300A Battery isolator switch, 900A for 30 secs, up to 48 Volt, M10 connection. Can be use on 12, 24 or 48 Volt system as long as switch current rating is not exceeded.

BLUE SEA M-SERIES SELECTOR SWITCHES

M-SERIES BATTERY SWITCHES

300 Ampere continuous rating.

• Tin-plated copper studs for maximum conductivity and corrosion resistance
• Studs accept 3⁄8" (M10) ring terminals
• 7⁄8" (22mm) stud length accepts multiple cable terminals
• One-piece terminal stud design never loosens over time
• Case design allows surface or rear panel mounting options
• Label with international legends
• Tactile indicator conveys knob position by feel

Regulatory

• CE marked, ISO 8846
• UL Listed - UL 1107 electric power switches
• Meets ABYC requirements
• Meets UL1500 and SAE J1171 external ignition protection requirements
• IP66 protects against powerful water jets

The SE7 side-entry twin cable gland is the perfect solution when space is limited or when loops from conventional top entry glands are not appropriate. Available in various finishes, the entire SE series of glands are tested achieving the IP68 rating which ensures a perfect waterproof solution for various cable management applications.  Each unit is supplied with clear fitting instructions and A4 stainless steel fixings. Suitable for two cables 3 – 6mm diameter supplied with tapered seals which ensure that the hole closes completely, creating a watertight seal around the cable. Ideal for electrical cabling applications and ducting through bulkheads, decks, and panels – i.e. VHF, Satnav, GPS and Radar installations.

Waterproof / dustproof (to IP68) gland with parallel low profile cable entry. Cable Size: 2 x 3mm – 2 x 6mm (3 pre-moulded bungs, no drilling required)

Designed for the Marine industry – IP68 for all applications

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 10m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Ideally 6mm solar cable max - for bigger units with bigger cable click here

Unit best used for housing 1 x AC RCBos, string fuse holders and fuses up to 32a as opposed to DC Din Mount breakers.

Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit.  If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.

This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.  

You will also need suitable cable entry glands - please see related products tab.

300A Fuse for 12v or 24 systems - Pack of 5 fuses

For use with Mega Fuse Holder

The VE.Direct cable is used for comunication between Victron VE Direct devices. For example it can be used to connect a Victron battery monitor to the Victron Colour Control or to connect a Victron GlobalLink 520 to a Victron MPPT Controller that has a VE direct port.

Mega Fuse stand alone fuse holder for the Victron Mega Fuses. M8 stud connection. Comes with translucent cover. 

One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.

Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off  the supply to a solar charge controller or solar inverter.

Choose fuse separately

Item dimensions 75mm H X 16mm W X 55mm D

Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line

Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.

The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.

This item fits String Fuse holder

6mm squared cable end lug for crimping onto 6mm² multi-stranded battery or solar cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK