The batteries come with inverter power cables and some comms cables for different inverters (see the alternative image for details).

When using a Victron GX device to handle comms, there is an included cable which we have tested and found that it works correctly for communication with Victron GX devices. Victron officially supports the use of Dyness batteries with Victron Systems. See more here: https://www.dyness.com/news/joint-compatibility-of-victron-and-dyness-allows-for-an-enhanced-user-experience and here: https://www.victronenergy.com/live/battery_compatibility:dyness for some basic setup requirements for use with Victron Systems.

These are heated batteries.

Commercial UK Install Video - Click downloads tab to view

Residental UK Install Video - Click downloads tab to view

HES 3-6K

Hybrid | Single Phase | LV

• Maximum 16A PV Input Current

• DC Ratio up to 2.0

• <10ms UPS Switch for Power Backup

• Shadow Scan Algorithm

• Support Both on and off-grid Operation

• Support Both Lead-acid and Lithium-ion Batteries

• Mutiple Periods for Battery Charging/Discharging

ADVANCED SAFETY REDEFINED

• Integrated Anti-islanding Protection
• Integrated Battery Reverse Protection
• Surge Protection
• DC Type II, AC Type III

HIGHER YIELDS

• Max. Input Current - 16A
• Max efficiency - 98.0%
• Low Start up Voltage - 70V

SPR-P6-405-BLK From the World's leading Solar Panel Manufacturer...

Enhanced Power Density
With high efficiency, LID-resistant solar cells (G12, 210mm), a lower temperature coefficient, and front-side conductive wires that support increased current collection, SunPower Performance panels are uniquely engineered to deliver more lifetime energy over standard solar panels.
 

Proven Reliability
A proprietary shingled-cell design maximises durability in all types of weather conditions—including reinforced cell connections that withstand the stresses of daily temperature swings, redundant electrical paths that alleviate the impact of cell cracks, and an advanced electrical architecture that is more resilient to the effects of shade and mitigates hot-spot formation.

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 15m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

The Lynx Power In contains a positive and negative busbar with 4 connections for batteries, loads or chargers and a ground connection. It is part of the Lynx Distribution system and is available in two versions, with M8 or M10 busbar. Note that M10 refers to the busbar connection joints where the modules are connected to each other. The fuse and cable connections are always M8.

For the Lynx product that accepts the mega fuses see: https://www.bimblesolar.com/victron-lynx-distributor

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.

The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.

NH00 rated at  250VDC, 160A,

Choose NH00 or NH000 fuses separately

Product measures 170mm H X 84mm W X 80mm D. Surface mountable.

DC Switch

• Modular design, DC insulation voltage 1500V, compact structure, 2-8 poles optional
• IP66 box design, switch rotation operator with three lockable positions, to prevent misoperation
• Suitable for different specifications of waterproof cable connector
• The zero line bridge with angle design makes the connection easier
• With sufficient internal space and good heat dissipation effect, the whole machine can work under -40℃-70℃ with full load
• High - speed "on - off" switching mechanism, using energy storage spring, fast switching, maximum switching time is less than 5ms
• Contact self-cleaning design, reduce the resistance and energy consumption of DC switch, extend the life of switch
• Magnetic arc extinguishing and gate arc extinguishing are used to suppress the arc effectively
• Passed IEC / EN60947-3: 2009+A1+A2, GB / T14048.3, with TUV, CE certification

NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC