The OutBack true sinewave GFX International Series Inverter/ Charger is a competitive power solution designed for applications with lower power demands. Incorporating a DC- to-AC sinewave inverter, battery charger and AC transfer relay housed within a die-cast aluminum chassis, the International Series GFX Inverter/Chargers give you the ability to sell solar, wind or hydro power back to the utility grid while providing instantaneous back-up power in the event of a utility outage.
The GFX International Series built in transfer relay automatically disconnects your loads from the utility grid and powers them from the inverter in the event of an outage, allowing you to continue using your solar and battery back- up power, unlike traditional grid-tie systems. For areas that frequently experience power instability such as surges, spikes or brownouts, or where standard inverters have trouble syncing to the utility grid, the GFX International Series grid reconnect timers have been set to reduce overall sell-back downtime and improve system functionality.
Intelligent multi-stage battery charging prolongs the life of your batteries and built-in networked communications allow for simultaneous communications of up to ten OutBack Power components within the system. The exclusive modular system architecture means that increased power output is just an additional inverter/ charger away. Our GFX International Series uses a sealed chassis that can operate in the harshest environmental conditions such as high humidity and corrosive salt air.
OutBack Power inverter/chargers are the only choice when you need a true-sinewave, powerful, modular and reliable power solution for your home, business or extreme application.
1300 watt continuous Output, with 1800 watts for 30 minutes and 2900 watts for 5 seconds.
Sealed True Sinewave Inverter/Charger
• Grid-Interactive, Backup or Standalone Power
• Sinewave Output
• Intelligent Battery Charging with Generator Support
• High Surge and Charger Ratings
• Sealed Chassis For Harsh Environments
• Field Serviceable
• Standard 5-Year Warranty
|Nominal DC Input Voltage||12 Vdc|
|Continuous Power Rating at 25°C (77°F)||1300 VA|
|AC Voltage/Frequency||230 Vac / 50 Hz|
|Continuous AC RMS Output at 25°C (77°F)||5,65 Aac|
|Idle Power||Full: ~ 18 Watts|
|Search: ~ 6 Watts|
|Total Harmonic Distortion||Typical: 2%|
|Output Voltage Regulation||± 2%|
|Maximum Output Current||Peak (1 ms): 28 Aac|
|RMS (100 ms): 20 Aac|
|AC Overload Capability||Surge (100 ms): 4600 VA|
|5 Second: 2900 VA|
|30 Minutes: 1800 VA|
|AC Input Current Maximum||30 Aac|
|AC Input Voltage Range (Adjustable)||140 to 280 Vac|
|AC Input Frequency Range||45 to 55 Hz|
|DC Input Voltage Range||10,5 to 17,0 Vdc|
|Continuous Battery Charge Output||70 Adc|
|Max DC Current at Rated Power||130 Adc|
|Warranty||Standard 5 year Warranty|
|Weight (kg/lbs)||Unit: 22,5 / 49,6|
|Shipping: 25,6 / 56,4|
|Dimensions H x W x L (cm/in)||Unit: 33 x 21 x 41 / 13 x 8,25 x 16,25|
|Shipping: 55 x 33 x 56 / 21,75 x 13 x 22|
Invented over 100 years ago by Thomas Edison as a non-polluting and non-consumable alternative to Lead Acid Batteries using no heavy metals! Now manufactured once again worldwide after lead acid battery companies closed Edison's Plant in 1972.
We have sourced NiFe at a competative rate at a little over double our cheap lead acid range and similar to our Rolls battery prices. This makes them a very viable option for long term off grid solutions.
You need 10 cells to make up a 12V bank, 20 cells for a 24V bank and 40 cells for a 48V bank
They have low operation cost, low self-discharge, long cycling life and environmental-friendly. They can withstand deep discharge, wide temperature variations, mechanical & electrical abuses and still show excellent and reliable performance over a long period. The operation life of solar Ni-Fe batteries is 30-40 Years, the working temperature range can be -40°C to 60°C, which is also the longest life battery for the PV system.
For more information on the advantages of NiFE batteries please read our info here
Optional LED fluid level indicator (£10 per cell)
Optional Auto Fill option (£15 per cell)
These have a long lead time as they are made to order and shipped over to us, please allow 2 months for delivery, but for a battery that will out live any other battery if your deciding to go down this route its definitely worth the wait and this is the reason we can keep the prices low.
These are the best charge controllers on the market, they are solid, reliable and what we use for The Bimble Inn.
The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Technologies. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30% compared to non-MPPT controllers. Thanks to active cooling and intelligent thermal management cooling, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 104°F (40°C).
Included in all of the FLEXmax Charge Controllers are the revolutionary features first developed by OutBack Power, including support for a wide range of nominal battery voltages and the ability to step-down a higher voltage solar array to recharge a lower voltage battery bank. A built-in, backlit 80 character display shows the current status and logged system performance data for the last 128 days at the touch of a button. The integrated OutBack network communications allows FLEXmax series Charge Controllers to be remotely programmed and monitored via a MATE system display and provides unrivaled complete system integration.
FLEXmax MPPT Charge Controllers are the only choice when you demand a high performance, efficient and versatile charge controller for your advanced power system.
|Voltage||Recommended PV Max||Absolute Max|
|FLEXmax 60 Specifications|
|Nominal Battery Voltages||12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up)|
|Maximum Output Current||60 amps @ 104° F (40°C) with adjustable current limit|
|Maximum Solar Array STC Nameplate||12 VDC systems 900 Watts / 24 VDC systems 1800 Watts / 48 VDC systems 3600 Watts / 60 VDC Systems 4500 Watts|
|NEC Recommended Solar Array STC Nameplate||12 VDC systems 750 Watts / 24 VDC systems 1500 Watts / 48 VDC systems 3000 Watts / 60 VDC Systems 3750 Watts|
|PV Open Circuit Voltage (VOC)||150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum|
|Standby Power Consumption||Less than 1 Watt typical|
|Power Conversion Efficiency||98.1% @ 60 Amps in at 48 VDC System voltage - Typical|
|Charging Regulation||Five Stages: Bulk, Absorption, Float, Silent and Equalization|
|Voltage Regulation Set points||10 to 80 VDC user adjustable with password protection|
|Equalization Charging||Programmable Voltage Setpoint and Duration - Automatic Termination when completed|
|Battery Temperature Compensation||Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell|
|Voltage Step-Down Capability||Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input|
|Programmable Auxilary Control Output||12 VDC output signal which can be programmed for different control applications
(Maximum of 0.2 amps DC)
|Status Display||3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total|
|Remote Display and Controller||Optional Mate or Mate2 with RS232 Serial Communications Port|
|Network Cabeling||Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires)|
|Data Logging||Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production|
|Hydro Turbine Applications||Consult factory for approved Turbines|
|Positive Ground Applications||Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications)|
|Operating Temperature Range||Minimum -40° to maximum 60° C
(Power capacity of the controller is automatically derated when operated above 40° C)
|Environmental Rating||Indoor Type 1|
|Conduit Knockouts||One 1" (35mm)on the back; One 1" (35mm) on the left side; Two 1" (35mm) on the bottom|
|Warranty||Standard 5 year / Available 10 Year|
|Weight - Unit||11.65 lbs (5.3 kg)|
|- Shipping||14.55 lbs (6.4 kg)|
|Dimensions - Unit||13.5 x 5.75 x 4" (40 x 14 x 10 cm)|
|- Shipping||18 x 11 x 8" (46 x 30 x 20 cm)|
|Options||Remote Temperature Sensor (RTS), HUB 4,
HUB 10, MATE, MATE 2
|Menu Languages||English & Spanish|
265W REC Surplus Stock Panels
Bargain Price - MCS Approved
Specs: - Download Full Spec Sheet
Peak Power Watts - Pmax(Wp)
Watt Class Sorting - (W)
Maximum Power Voltage - Vmpp(V)
Maximum Power Current - Impp(A)
Open Circuit Voltage - Voc(V)
Short Circuit Current - Isc (A)
Panel Efficiency (%)
Certified according to CE, TUV, VDE, MCS, UL, CSA, IEC 61215 and IEC61730
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
Get 5% discount for Bank Transfer Payments This is automatically applied to your order when you select bank transfer in checkout.
Delivery from £26
First panel £26, each additional panel just £6 delivery
ie: 3 panels costs £38 delivery.
Delivery service is an economy service that hand delivers fragile items on a weekly round across the UK.
Surcharge for remote areas including parts of Wales, Scotland, Ireland and Isle of Wight, please see Delivery info
This is a safer more reliable and cheaper way for you to receive panels and saves on the huge amounts of wasted packing materials.
Pallet Shipping 25 panels per pallet:
£175 UK Mainland
£375 Rest of Europe
Or you can collect for FREE from Nr Brighton.
The new MATE3 System Display and Controller makes it easy to program and monitor a complete OutBack Power System. An intuitive and integrated system configuration wizard makes system setup and programming quick and seamless.
The ability to set unique multi-level user passwords allows the user to secure critical system settings from unintended changes, while still allowing open access to necessary functions.
The MATE3 is packed full of features to make system management simple. The easy-to-read graphical LCD display is backlit for dark operating conditions. Improved tactile buttons and a user programmable “favorite” key give you immediate access to the features you want, while an intuitive scroll wheel interface allows for easy adjustment of system setpoints. Expandable SD card memory allows you to increase data logging capacity as well as upgrade units in the field.
A built-in clock and calendar function enables timer-based programming of inverter and charger operation. All of your settings are stored in permanent memory to eliminate the need to reprogram in the event of a system shutdown or battery replacement. The MATE3 is an Internet enabled device – simply connecting to the Internet will allow full remote system.
By adding the Mate Controller you can also use the outback inverters as a off grid/grid hybrid system allowing you to use the power from your batteries primarily and switching to use the grid when your batteries are low, thus minimising your use of the grid and ensuring you get the best use of your renewable power set-up, and yet never run out of power. Or you can configure an automatic generator start from them if needed.
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
16mm cable - for Large Charge Controller to Batteries - 2 Meter leght with M8 Lug
You will need 2 cables per charge controler (Pos & Neg). The Lugs are on 1 end only as the charge controllers have bare wire connectors.
If you need longer lengths please let us know
6mm Solar Cable - Price is per meter simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable
Max load: 50A
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
50mm Cable - Use for connecting Batteries to Inverter M8 - M10 (M8 one end M10 on the other end)
You will need 2 cables, 1 for Positive and 1 for Negative
If you need a longer cable please let us know.
MC4 Solar Connector - Price is per pair simply select the quantity as the number of pairs you want.
These are the standard connectors used on most solar panels.
TUV certified, brand new, water /weather proof rubber seal that can ensure excellent electrical contact for life time service.
The metal pin is made from high quality machined copper and sealed tip (compare to the cheap sheet metal pin) that can ensure excellent electrical contact for life time service.
Build in press tabs for easy disconnect, no tool is needed. 25A max load.
Wires should be crimped or soldered into the pins and care should be taken to get the correct pin into the correct connector. Once the pin is pushed into the connector it is difficult to remove without the correct tooling.
Main Technical Specification:
Maximum Current: 25A
Maximum voltage: 1000V
Maximum operating humidity: 5% -95% (No condensation)
Temperature: -40 ℃ ~ +90 ℃
Waterproof Grade: IP67
Flame class: UL94-V0
Connecting cable specifications: 2.5mm2 4mm2 6mm2
Test voltage: 6.6KV (50Hz, 1min)
Metal materials: nickel copper
Insulation material: PA12 * 1988HB
Lock mode: Self-locking
Security Level: Class ‖
Shell has a strong anti-aging, anti- UV capability; found in outdoor use under harsh environment requirements; according to different needs can be arbitrary and used in conjunction with a variety of cell junction box; all connections are using press-fit connection;