Dual input 20A charger with selectable charge voltages

The D250SE is a fully automatic, 5 step charger that supplies up to 20A of power to any 12V lead-acid or ­lithium* service battery from 40–300Ah. It has ­selectable charge algorithms for AGM and lithium* batteries and can use power through its dual input from alternator, solar panel and wind power. When the service battery is fully charged, the D250SE will ­automatically redirect maintenance charge ­power to the starter battery. The D250SE can maintain a stable output up to 20A to vehicles fitted with smart ECU controlled ­alternators and also has a temperature sensor for ­optimised charging, regardless of weather conditions. *) 12V lithium batteries (LiFePO4, Li-Fe, Li-iron, LFP)

Features

• Battery separation replacing diodes and VSR relays
• Selectable AGM option – 14.4V or 14.7V
• Maximised charging for better battery life and performance
• Temperature sensor to compensate for hot or cold conditions
• Splash and dust proof (IP65)
• Compatible with SMARTPASS 120, SMARTPASS 120S for the ultimate 140A power management solution
• 2-year warranty

175W Perlight All Black Mono Perc Panel - 1080 x 885 x 30mm

A beautiful all black solar panel with no busbars for a nice sleak look on your roof.

Fixes without screwing holes in your roof!

Panels over 175w should be bolted down, these are unsuitable.

Set of seven black solar panel mounting kit, including 6 brackets (4 corners and 2 sides) and cable gland.  They are ideal for fixing our solar panels to any vehicle, caravan, boat, barge or even outbuildings and sheds to provide a strong, secure and aesthetically pleasing fixing method, the mounts will support the solar panel at the correct height above the surface to enable the flow of air underneath the panel and keep it cool, ensuring the solar panel functions at it's optimum. The mounts can be safely bonded to the surface removing the need to drill holes.  The panel is secured by screwing or bolting it to the mounting corner, but the corner itself can be fixed with a good strong adhesive like 'Sikaflex' or 'CT1' or any polyurethane sealant to the roof. (Ensure the roof is clean and dry before attaching.   If a painted roof ensure the paint is not flakey)

ABS mounts raise the panel by 25mm.  Edge of panel to edge of ABS is 55mm.

We sell CT1 which is great for sticking these down, please see related products tab for different colours avaialble.

If you are fitting to a vehicle we recommend that you additionally bolt or screw the panel and mounting down as well, as the strength of these systems is only as strong as the roof type or paint on your roof!

NOTE - You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method...

Here is a good tutorial to get you started:

ABS Mounting tutorial

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Ideally 6mm solar cable max - for bigger units with bigger cable click here

Unit best used for housing 1 x AC RCBos, string fuse holders and fuses up to 32a as opposed to DC Din Mount breakers.

Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit.  If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.

This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.  

You will also need suitable cable entry glands - please see related products tab.

For use with our stick down panels and ABS mounting kits - also great for sealing cable holes

CT1 will successfully bond:

• Metals (including lead)
• Glass
• Mirrors
• Wood
• Polystyrene

Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals

• Prevents fungal growth
• UV resistant
• Excellent resistance to vibration
• Food safe - conforms to ISEGA Standards
• Works in wet or dry conditions
• Perfect for marine and boating maintenance, accident and emergency repairs
• Can be used in all salt-water environments
• Odourless
• Does not shrink
• Can be painted
• Contains no solvents
• No isocyanates
• Unique flexibility
• Environmentally compliant
• Instant repair and bonding with fibre glass and carbon fibre materials

Application
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)

Drying Time
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.