The Pylontech US3000C has an incredible DoD of 95%.
You can now register the Pylon US3000C for an additional 3 years of manufacturer warranty for free. Go to Pylon Support and complete the information in the 'sign up battery' page.
The US3000C can be used to expand an existing US3000 bank. Please note, the US3000C needs to be used as the master battery when used to expand an existing US3000 bank.
DIP switch has been deployed reversely. ON is down, OFF is UP. If DIP switches need to be 1000 then set it to 1110. MAX DISCHARGE AND CHARGE RATE IS ONLY APPLICABLE FOR +- 60 SECONDS
If using this battery with Victron equipment it requires a Type A communications cable to the Victron GX device not a Type B.
You can optionally add mounting brackets BRACK-US3000 to this product for a stable base, and to allow easy stacking of multiple units.
If you want to use these batteries with Victron equipment please read this article to select the correct equipment:
Here is the link to register your batteries and receive extended warranty:
The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.
The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.
Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.
Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.
FOR LARGE PANEL DELIVERY TIMES, SCHEDULES AND COSTS - CLICK HERE
Super High Efficiency Mono PERC Module (CS6R-410MS) Dimensions: 1722 X 1134 X 30mm
Cables from rear junction box are approx 1m positive and 1m negative.
This panel has a silver frame.
CANADIAN SOLAR INC.is committed to providing high quality solar products, solar system solutions and services to customers around the world. As a leading PV project developer and manufacturer of solar modules with about 30 GW deployed around the world since 2001, Canadian Solar Inc. is one of the most bankable solar companies worldwide.
With proprietary mono wafer and cell technologies Canadian Solar have developed an extraordinary module rage. Combining the best technology and design, it also reduces LCOE and installation costs.
The Super High HiKu mono modules with dimensions of 1722 X 1134 X 30mm, have the following unique features:
MORE RELIABLE (THANKS TO HALF CUT CELL TECHNOLOGY):
Cell: 120 x dual-cell Mono, 156 x 78 mm
Dimensions: 1722 X 1134 X 30mm
Weight: 21.3 kg
A modular heavy duty DC bus bar with locations for four DC fuses. It has a positive and negative bus bar. The Lynx distributor can link (piggy back) onto each other to form a larger bus bar for a variety of applications. For use stand alone or with the Lynx modular system, see manual under the downloads tab.
It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar https://www.bimblesolar.com/Victron-lynx-powerin
A set of battery brackets which allows vertical stacking of the Pylon US3000 battery unit. 1 set required per battery.
6mm² Solar Cable - Price is for a 100 meter reel. If you wish to buy in lower quantity meter lengths, please see https://www.bimblesolar.com/6mmcable
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Class 5 flexible tinned copper conductor
Halogen-free cross-linked compound
Halogen-free cross-linked, flame retardant compound
Other colours available on request if bulk order
**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**
One pole fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or charge controller and battery. Integrated handle enabling use as an isolator.
NH00 rated at 250VDC, 160A
Choose NH00 or NH000 fuse separately
Item dimensions 170mm H X 42mm W X 80mm D
125A Fuse for 48V systems
For use with Mega Fuse Holder, or Lynx Distributor
Pylon battery cable accessory kit for use with all the different battery models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the inverter/charger.
Please check the number of cable packs you need, according to your inverter/charge specifications. Each cable pack is rated at 100A continuous, and 125A peak.
This cable pack includes the following cables:
2 x 2m long power cables (1x positive and 1x negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.
Victron MK3-USB Configuration Interface
The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.
Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.
The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.
This industrial quality Multi-Contact tool is a first priority for Crimping MC4 male and female solar contacts, used for the cable(2.5/4/6 mm2)
The excellent handling, easy exchange of the crimping insert bits and the possibility of adding a positioning aid are facts in favour of these crimping pliers.
Mechanical Hexagonal crimp tool for 10mm² -120mm² copper tube terminal lugs. For manual crimping of terminal lugs and pin ferrules onto battery cable. 45cm long handles.
300A Battery isolator switch, 900A for 30 secs, up to 48 Volt, M10 connection. Can be use on 12, 24 or 48 Volt system as long as switch current rating is not exceeded.
M-SERIES BATTERY SWITCHES
300 Ampere continuous rating.
One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.
Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off the supply to a solar charge controller or solar inverter.
Choose fuse separately
Item dimensions 75mm H X 16mm W X 55mm D
10mm tinned copper Solar Cable - Price is per meter simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable, 6.9mm Outer Diameter, Halogen-free cross-linked
Max load: 98A
European standard solar cable intended for the interconnection within photovoltaic systems such as solar panel arrays. Suitable for fixed installations, internal and external, within conduit or systems, but not direct burial applications. Our solar cable is ozoneresistant according to BS EN 50396, UV resistant according to HD 605 S2 and is tested for durability according to EN 60216.
200A Fuse for 48V systems
For use with Mega Fuse Holder
STÄUBLI MC4 Solar PV connectors - Pair
Connect your solar modules together with ease using these safe and durable genuine Staubli MC4 connectors. Snap-in lock. MC4 crimp tool required to make onto cable ends. YOUTUBE VIDEO
32.0016P0001-UR & 32.0017P0001-UR
See DOWNLOADS TAB for datasheet
|Cable diameter||5.9 to 8.8 mm|
|Cable cross-section||4.0-6.0 mm²|
|Rated voltage IEC||1000 V|
|Rated current IEC||39 A|
|UL recognized component, in accordance with UL 6703||
*Please note male and female refers ot the metal conductor and not the plastic insulator*
Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line
Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.
The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.
This item fits String Fuse holder
Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.
NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.
Fuses are rated at 250VDC
Copper busbar for parallel our solar string fuse holders or the Tomzn DC breaker <63A in the solar combiner box to take a single feed to a charge controller for example.
10 mm², 17.5mm partition (distance between centre of poles), peg design, L-shaped bar. The busbar comes with a plastic cover. Cut the busbar down to the number of poles required for your application. Use the feeder to take a single feed from the bus bar. Made in Germany
Din rail mountable junction block for joining conductors of like polarity. Can be use for joining/combining the negative conductors in our PV combiner boxes. M6 terminal lugs required separately. Additional M6 nuts and washers recommended if stacking multiple terminals on the M6 posts.
Use the feeder terminal to take a single feed from the bus bar in the solar combiner box to a solar charge controller for example. The feeder terminal accepts from 6 - 25mm² cable and the pin length is 15mm. Consider using a ferrule or flat pin lug on the end of the cable go into the female end of the terminal. Made in Germany
70mm squared cable end lug for crimping onto 95mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK
25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK
Bag of 10 x 6mm Ring Yellow Crimps - 48A max current.
for 4mm or 6mm cable
10mm squared cable end lug for crimping onto 10mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK