TNE Series, TN’s most powerful products, are specially designed for deep cycle application. With numbers of national patent technologies, the cycle life reaches 400-600 cycles at 100% DOD, highly suitable for golf carts, electric wheelchairs, low-speed electric vehicles etc. Maintenance free technology reduce the complexity with water adding during use and become more and more popular in the market.

For 12V Solar System: 750W solar panel (150V for max input voltage 138V@ 25C)
For 24V Solar System: 1500W solar panel (150V for max input voltage 138V@ 25C)
For 48V Solar System: 3000W solar panel (150V for max input voltage 138V@ 25C)

**The controller can only set lead-acid battery types. Lithium battery types must be set through the PC or APP.**

No Fan for silent operation, great for vans, boats or any live in spaces

​The AN tracer models have a current limiting function, you can connect 1.5 times the rated power to the controller ​so if your on a budget you can use a smaller controller with more panels so that you get more power in winter or low light but don't risk overloading the controller in the summer.  The output will be limited to the max listed above.

Supports upto 6 units in parallel with a PTA adapter for communication and equalize of the paralleled units

Local temperature sensor included, remote 3m temperture sensor optional.

Tracer AN series controller, based on multiphase synchronous rectification technology (MSRT) and advanced MPPT control algorithm, with dual-core processor architecture and common negative design, has the features of high response speed, high reliability, and high industrial standard. MSRT can guarantee very high conversion efficiency in any charge power, which sharply improves the energy efficiency of solar system; Advanced MPPT control algorithm minimize the maximum power point loss rate and loss time, to ensure the tracking efficiency, corresponding speed as well as high conversion efficiency under high or low power, so that in any situation, Tracer AN products can rapidly track the maximum power point (MPP) of PV array to obtain the maximum energy of the panel. The limitation function of the charging power and current and automatic power reduction function fully ensure the stability when works with oversize PV modules and operate under high temperature environment.

With the adaptive three-stage charging mode based on digital control circuit, Tracer AN series controllers can effectively prolong the life-cycle of battery and significantly improve the system performance. The load, utility or generator auto-control relays make it easy to compose the hybrid power system. All-around electronic protections, including overcharging, over discharging, and PV reverse polarity protection, effectively ensure the safer and more reliable operation of the solar system for a longer service time. The isolated RS485 interface with standard MODBUS communication protocol and 5V power supply makes it easy for customer to expand the application, Support up to 8 charging in parallel to expand system and meet with different monitoring requirements, so that can be widely used for various applications, e.g. solar RV, household system and field monitoring, etc.

Features

• CE certification(LVD EN/IEC62109,EMC EN61000-6-1/3)
• High quality & low failure rate components of ST and Infineon to ensure the product’s life
• Advanced MPPT technology & ultra-fast tracking speed is up to 99.5% guaranteed
• Maximum DC/DC transfer efficiency is as high as 98.7%
• Advanced MPPT control algorithm will minimize the MPP loss rate and loss time
• The accuracy of the recognition and tracking at the highest point of multiple-peaks MPP
• The wider range of MPP operating voltage.
• Auto control system to limit the charging power & current go over the rated value.
• Support 4 charging options: Sealed, Gel, Flooded and User.
• Battery temperature compensation function
• Real-time energy recording and statistical function
• Automatic over-temperature power reduction function
• Hundred percent full load operation in working environment temperature range within charging & discharging
• Support up to 6 units in parallel to expand system
• Load relay control external load switch signal to realize diversified load work modes
• The first and the second disconnection of load control, contain two relay’s contact.
• Auto-control of utility and generator relay design
• Utility or generator auto-control relays make it easy to compose the hybrid power system
• The remote temperature and the voltage sensor design will collect accurate data of battery temperature and voltage
• Isolated RS-485 with 5VDC/200mA to protect output for no power devices with MODBUS protocol
• To monitor or set the parameters by using the phone Apps or PC software.

Protection:

• PV Over Current/power • Night Reverse Charging • Battery Overheating
• PV Short Circuit
• Battery Over Voltage
• Controller Overheating
• PV Reverse Polarity
• Battery Over Discharge
• TVS High Voltage Transients

 1At minimum operating environment temperature;
2At 25°C environment temperature
3The maximum PV open circuit voltage must never exceed 138V or 180V at 25°C environment temperature.

Download Manual 

Victron pure sinewave output, high peak power and high efficiency in a compact unit. Models range from 250VA to 1200VA with UK socket - other socket outlets available on request

These inverters allow you to power domestic equipment - requiring 230VAC - using 'leisure' or 'automotive' batteries rated at 12V

Bulit in DC fuse in all models but not replaceable in all models - see the manual for further details on which models carry the replaceable fuse.

Consider adding a battery isolator switch https://www.bimblesolar.com/300a-blue-sea-battery-isolator

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level Monitoring:

• In- and output voltage, % load and alarms

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector

Spec Sheet

See the Download tab on this listing

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Set of 4 Aluminium mounting brackets for mounting solar panels on vans, boats, sheds or a wooden frame as a easy cheap solar framing system.

** Panels larger than 100w are not recommended to use these alone, as a direct fixing to a vehicle roof.  We suggest a bespoke solution using bolts, some of our customers use these brackets and modify them to achieve this, others get a locally fabricated solution **

Includes:
Aluminium mounting brackets;
Wood screws:St5.7 mm*30mm,
Socket Head Screw:M6*25mm,

Optional Meter for AN, BN, CN, XTRA MPPT charge controllers.  DuoRacer requires the MT11, see separate listings.

Comes with 2m RJ45 cable in the box, if you need longer we have a 5m cable here 5m RJ45 Cable for MT50

PLEASE NOTE - YOU CANNOT USE THE MT50 AT THE SAME TIME AS THE BLUETOOTH / WIFI OPTIONAL ADAPTORS

Features:
·Automatic identify  the controller, and display the type, model and relevant parameter data
·Large-screen multifunction LCD  displays all the operational data and system working status  in digital, graphic and textual forms
·With six navigation function keys, the  operation is direct, convenient and rapid
·Real-time energy statistics recording
·Both data and data flowing on the same lead, no need for  external power
·Real-time monitoring and acoustic alarm of failure information of the controller
·Longer communication distance based on RS485

Functions Via MT50
·Diversified load control modes : manual, light ON/OFF, Light ON+ Timer, Time Control
·Battery type selection: Gel, sealed, flooded and USER type
·Real-time monitor
·Programmable parameters
·Energy display function

Download Guide to change language

Please note: Older MT50s manufactured before August 2017 are not compatible with the newer XTRA and AN controllers.

Use with lithium batteries:  The MT50 ( sv 2.18 version) can be used to program a lithium battery for our XTRA controllers. However it cannot do this for the Tracer-AN 60A and 100A. You must use a PC cable and software for programming lithium.

Ideally 6mm solar cable max - for bigger units with bigger cable click here

Unit best used for housing 1 x AC RCBos, string fuse holders and fuses up to 32a as opposed to DC Din Mount breakers.

Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit.  If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.

This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.  

You will also need suitable cable entry glands - please see related products tab.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

A small, low cost multimeter supplied with test leads and holster.

• 3½ digit, 1999 count display
• AC/DC voltage measurement
• DC current
• Resistance measurement (20R to 2MR)
• Diode, continuity and transistor tester
• Square wave output
• Low battery indication
• Requires a 9V PP3 battery (included)

DMM Functions: DC Current, AC/DC Voltage, Continuity, Diode, Resistance, Transistor
No. of Digits: 3.5  
DMM Response Type: Average  
Display Count: 1999  
Range Selection: Manual  
Voltage Measure DC Max: 500V  
Voltage Measure AC Max: 500V  
Current Measure DC Max: 5A  
Resistance Measure Max: 2Mohm