Q Cells 390W Mono Q Peak Duo G9 Black Frame HQC4 Panels - Monocrystallines

• Rating: 390W
• Efficiency: 20.6%
• Width: 1,030mm
• Height: 1,840mm

Patent protected Q.Antum passivated emitter rear contact (PERC) technology, 132 (half) cell format with zero gap cell layout, boosts module efficiency up to 20.8%

• Optimal yields, whatever the weather with excellent low-light and temperature behaviour.

• Long-term yield security with Anti LID Technology, Anti PID Technology1, Hot-Spot Protect and Traceable Quality Tra.Q™.

• Extreme weather rating. High-tech aluminium alloy frame, certified for high snow (6000Pa) and wind loads (4000Pa).

• Includes 12-year product warranty and 25-year linear performance warranty

• Q.ANTUM DUO combines cutting edge cell separation and innovative wiring with Q.ANTUM technology

Please Note: Q Cells do not recommend their modules to be fitted on In-Roof mounting systems like the GSE In-Roof system

ESSENTIAL TOOLKIT LINK BELOW, PURCHASE IF YOUR INSTALLER DOES NOT HAVE THESE PARTS:

TOOLKIT LINK HERE

A pair of 2mm stainless steel (316L) solar panel brackets designed with canalboats and vehicles in mind, supplied with marine standard cable glands and anti tamper bolts & bit. 

Allow your solar panels to both tilt and swivel throughout the year, maximising the sun's energy whilst providing excellent ventilation. This can improve the power of your panels by up to 40%, perfect for smaller systems where efficiency is key. *Standing at just over 25cm high and 16cm  wide they're designed to maximise the angle of your panels whilst being low enough for most bridges and tunnels. 

Using any padlock attach your panel securely to the roof via an integrated 8mm stainless steel chain that secures directly to the bracket, keeping your panels safe. The anti tamper bolts secure the bracket to your roof for maximum security deterring even the most determined of thieves.

Using M10 for both bolts and glands means you only need to drill six identical holes, saving both time and money on tools or labour whilst providing a safe and secure mounting solution. 

Tool Kit

A tool kit with everything you need for a waterproof and secure installation supplied separately, select the tool kit option to purchase this as well.

2 top spec cobalt drill bits and M10 tap and ratchet allow quick and easy installation with even the toughest steel roof.

Supplied with marine sealant, a secure and waterproof installation can be done in as little as 4 hours.  

Click here for Technical Spec Sheet

For 12V Solar System: 750W solar panel (150V for max input voltage 138V@ 25C)
For 24V Solar System: 1500W solar panel (150V for max input voltage 138V@ 25C)
For 48V Solar System: 3000W solar panel (150V for max input voltage 138V@ 25C)

No Fan for silent operation, great for vans, boats or any live in spaces

​The AN tracer models have a current limiting function, you can connect 1.5 times the rated power to the controller ​so if your on a budget you can use a smaller controller with more panels so that you get more power in winter or low light but don't risk overloading the controller in the summer.  The output will be limited to the max listed above.

Supports upto 6 units in parallel with a PTA adapter for communication and equalize of the paralleled units

Local temperature sensor included, remote 3m temperture sensor optional.

Tracer AN series controller, based on multiphase synchronous rectification technology (MSRT) and advanced MPPT control algorithm, with dual-core processor architecture and common negative design, has the features of high response speed, high reliability, and high industrial standard. MSRT can guarantee very high conversion efficiency in any charge power, which sharply improves the energy efficiency of solar system; Advanced MPPT control algorithm minimize the maximum power point loss rate and loss time, to ensure the tracking efficiency, corresponding speed as well as high conversion efficiency under high or low power, so that in any situation, Tracer AN products can rapidly track the maximum power point (MPP) of PV array to obtain the maximum energy of the panel. The limitation function of the charging power and current and automatic power reduction function fully ensure the stability when works with oversize PV modules and operate under high temperature environment.

With the adaptive three-stage charging mode based on digital control circuit, Tracer AN series controllers can effectively prolong the life-cycle of battery and significantly improve the system performance. The load, utility or generator auto-control relays make it easy to compose the hybrid power system. All-around electronic protections, including overcharging, over discharging, and PV reverse polarity protection, effectively ensure the safer and more reliable operation of the solar system for a longer service time. The isolated RS485 interface with standard MODBUS communication protocol and 5V power supply makes it easy for customer to expand the application, Support up to 8 charging in parallel to expand system and meet with different monitoring requirements, so that can be widely used for various applications, e.g. solar RV, household system and field monitoring, etc.

Features

• CE certification(LVD EN/IEC62109,EMC EN61000-6-1/3)
• High quality & low failure rate components of ST and Infineon to ensure the product’s life
• Advanced MPPT technology & ultra-fast tracking speed is up to 99.5% guaranteed
• Maximum DC/DC transfer efficiency is as high as 98.7%
• Advanced MPPT control algorithm will minimize the MPP loss rate and loss time
• The accuracy of the recognition and tracking at the highest point of multiple-peaks MPP
• The wider range of MPP operating voltage.
• Auto control system to limit the charging power & current go over the rated value.
• Support 4 charging options: Sealed, Gel, Flooded and User.
• Battery temperature compensation function
• Real-time energy recording and statistical function
• Automatic over-temperature power reduction function
• Hundred percent full load operation in working environment temperature range within charging & discharging
• Support up to 6 units in parallel to expand system
• Load relay control external load switch signal to realize diversified load work modes
• The first and the second disconnection of load control, contain two relay’s contact.
• Auto-control of utility and generator relay design
• Utility or generator auto-control relays make it easy to compose the hybrid power system
• The remote temperature and the voltage sensor design will collect accurate data of battery temperature and voltage
• Isolated RS-485 with 5VDC/200mA to protect output for no power devices with MODBUS protocol
• To monitor or set the parameters by using the phone Apps or PC software.

Protection:

• PV Over Current/power • Night Reverse Charging • Battery Overheating
• PV Short Circuit
• Battery Over Voltage
• Controller Overheating
• PV Reverse Polarity
• Battery Over Discharge
• TVS High Voltage Transients

 1At minimum operating environment temperature;
2At 25°C environment temperature
3The maximum PV open circuit voltage must never exceed 138V or 180V at 25°C environment temperature.

Download Manual 

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 15m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

35mm Cable - Use for connecting Batteries to Inverter

You will need 2 cables, 1 for Positive and 1 for Negative

If you need a longer cable please let us know.

Save yourself hours of drilling!  Get our essential toolkit for installing the boat swivel mounts!

Contains:

Cobalt drill bits (for drilling into the panel frame and boat hull) 8.5mm and 5.5mm

Ratchet and Tap set (Taper, Plug & Bottoming)

Marine Sealant

Optional Meter for AN, BN, CN, XTRA MPPT charge controllers.  DuoRacer requires the MT11, see separate listings.

Comes with 2m RJ45 cable in the box, if you need longer we have a 5m cable here 5m RJ45 Cable for MT50

PLEASE NOTE - YOU CANNOT USE THE MT50 AT THE SAME TIME AS THE BLUETOOTH / WIFI OPTIONAL ADAPTORS

Features:
·Automatic identify  the controller, and display the type, model and relevant parameter data
·Large-screen multifunction LCD  displays all the operational data and system working status  in digital, graphic and textual forms
·With six navigation function keys, the  operation is direct, convenient and rapid
·Real-time energy statistics recording
·Both data and data flowing on the same lead ,no need for  external power
·Real-time monitoring and acoustic alarm of failure information of the controller
·Longer communication distance based on RS485

Functions Via MT50
·Diversified load control modes : manual, light ON/OFF, Light ON+ Timer, Time Control
·Battery type selection: Gel, sealed, flooded and USER type
·Real-time monitor
·Programmable parameters
·Energy display function

Download Guide to change language

Please note: Older MT50s manufactured before August 2017 are not compatible with the newer XTRA and AN controllers.

Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you could cut in half giving you 2 x 1m lengths MC4 to bare wire)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

STÄUBLI MC4 Solar PV connectors - Pair of Y Branches

Connect your solar modules together with ease using these safe and durable MC4 connectors.  This pair of "Y" shape connectors (one in a male to female, female configuration, and one in a female to male, male configuration) will allow you to connect panels or strings of panels together.  If you need to connect 3 panels together then it is cheaper to use 2 pairs of these than to purchase a 3 way splitter (its about 1/3 of the cost to use these)

Product information:

Cable Gland Entry Box, use to connect through external surface.  Perfect for solar panel cables coming from outside to controller.

This comes with a cradle for keeping your MC4 connectors in place and tidy.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

A small, low cost multimeter supplied with test leads and holster.

• 3½ digit, 1999 count display
• AC/DC voltage measurement
• DC current
• Resistance measurement (20R to 2MR)
• Diode, continuity and transistor tester
• Square wave output
• Low battery indication
• Requires a 9V PP3 battery (included)

DMM Functions: DC Current, AC/DC Voltage, Continuity, Diode, Resistance, Transistor
No. of Digits: 3.5  
DMM Response Type: Average  
Display Count: 1999  
Range Selection: Manual  
Voltage Measure DC Max: 500V  
Voltage Measure AC Max: 500V  
Current Measure DC Max: 5A  
Resistance Measure Max: 2Mohm  

Simple DIN mount rail 10cm long for DC or AC DIN mount breakers.  Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it.  Quick easy and simple solution to install breakers to your solar system.

Use with our:

• DC DIN mount breakers
• RCBO AC breakers.