For Victron and Pylontech systems, please check the following manual link
Please use a dimension of 4U per module when sizing a cabinet for these batteries.
If you want to use these batteries with Victron equipment please read this article to select the correct equipment:
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
Here is the link to register your batteries and receive extended warranty:
https://en.pylontech.com.cn/service/registration
The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.
The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.
Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.
Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
MultiPlus-II inverter/charger.
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.
GX device
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.
From the World's leading Solar Panel Manufacturer...
The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. It is part of the Lynx Distribution system and is available in two versions, with M8 or M10 busbar. Note that M10 refers to the busbar connection joints where the modules are connected to each other. The fuse and cable connections are always M8. The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can.
*This listing is for the M8 version.*
It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar https://www.bimblesolar.com/Victron-lynx-powerin
6mm² Solar Cable - Price is for a 100 meter reel. If you wish to buy in lower quantity meter lengths, please see https://www.bimblesolar.com/6mmcable
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Other colours available on request if bulk order
A set of battery brackets which allows vertical stacking of the Pylon US5000 battery unit. 1 set required per battery.
Victron MK3-USB Configuration Interface
The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.
Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.
Supported Platforms
The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.
Description
This industrial quality Multi-Contact tool is a first priority for Crimping MC4 male and female solar contacts, used for the cable(2.5/4/6 mm2)
The excellent handling, easy exchange of the crimping insert bits and the possibility of adding a positioning aid are facts in favour of these crimping pliers.
Tools Parameters
Capacity: 2.5-6.0mm2
AWG: 26-10AWG
Length: 270mm
Weight: 0.74Kg
This outdoor rated combiner box is for safely combining larger strings of solar panels >= 3. The box comes fitted with Din rail and 10 X M20 glands with a cable outer diameter range of 5 - 10mm.
The enclosure features knock out discs so no drilling is required. Just punch out the number if gland spaces required, and fit the glands. You must select the fuse holder, fuses, bus bar, feeder terminal and extra glands if required for your system. See related items tab above to see the breakers that fit. If fusing positive conductors only, select Din rail block to combine the negatives. It is possible to mount he box without puncturing it thus maintaining the IP waterproof rating
Outside dimensions: 182 X 180 X 111mm
Inside dimensions: 167 X 165 X 96mm
Effective Din rail length: 150mm
Number of gland knock outs: 8 X M20, 1 X M25 or M32 (top & bottom), 4 X M20, 1 X M32 or M40 (left side and right side)
Mechanical Hexagonal crimp tool for 10mm² -120mm² copper tube terminal lugs. For manual crimping of terminal lugs and pin ferrules onto battery cable. 45cm long handles.
**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**
Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.
The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.
NH00 rated at 250VDC, 160A,
Choose NH00 or NH000 fuses separately
Product measures 170mm H X 84mm W X 80mm D. Surface mountable.
Pylon battery cable accessory kit for use with all the different battery models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the inverter/charger.
Please check the number of cable packs you need, according to your inverter/charge specifications. Each cable pack is rated at 100A continuous, and 125A peak.
This cable pack includes the following cables:
2 x 2m long power cables (1x positive and 1x negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.
The Battery Switch ON/OFF 275A is suitable for battery systems up to 48V. It has a unique ergonomic and aesthetic knob design. The knob is removable for isolation or safety purposes.
The Battery Switch can be either surface or panel mounted, providing flexibility during install.
The Battery Switch meets the ISO8846 Ignition Protection standard and is suitable for use in an engine room.
10mm tinned copper Solar Cable - Price is per meter simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable, 6.9mm Outer Diameter, Halogen-free cross-linked
Max load: 98A
European standard solar cable intended for the interconnection within photovoltaic systems such as solar panel arrays. Suitable for fixed installations, internal and external, within conduit or systems, but not direct burial applications. Our solar cable is ozoneresistant according to BS EN 50396, UV resistant according to HD 605 S2 and is tested for durability according to EN 60216.
One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.
Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off the supply to a solar charge controller or solar inverter.
Choose fuse separately
Item dimensions 75mm H X 16mm W X 55mm D
200A Fuse for 48V systems
For use with Mega Fuse Holder
Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line
Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.
The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.
This item fits String Fuse holder
STÄUBLI MC4 Solar PV connectors - Pair
Connect your solar modules together with ease using these safe and durable genuine Staubli MC4 connectors. Snap-in lock. MC4 crimp tool required to make onto cable ends. YOUTUBE VIDEO
Manufacturer SKU
32.0016P0001-UR & 32.0017P0001-UR
See DOWNLOADS TAB for datasheet
Technical specifications
Connection | crimp connection | |
Version | jack | |
diameter | 5.8 mm | |
Cable diameter | 5.9 to 8.8 mm | |
Cable cross-section | 4.0-6.0 mm² | |
Rated voltage IEC | 1000 V | |
Rated current IEC | 39 A |
UL recognized component, in accordance with UL 6703 |
|
*Please note male and female refers ot the metal conductor and not the plastic insulator*
• Complies to ISO 20934
• Cu alloy element
• Tin plated integrated heatsink
• Riveted PPA GF35 thermoplastic colour coded housing
• Colour coded housing with value in OCR font on both sides
ELECTRICAL & SPECIFICATIONS
Input Voltage 70V DC Maximum
Breaking capacity 2500A at 70VDC
Dimensions 68mm x 19mm x 10.5mm
Hole size M8
Hole centres 50.9mm
Maximum torque 12Nm ± 1 Nm
Identification Colour coded housing and value in OCR font on both sides
Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for Pylontech C series batteries and BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.
Din rail mountable junction block for joining conductors of like polarity. Can be use for joining/combining the negative conductors in our PV combiner boxes. M6 terminal lugs required separately. Additional M6 nuts and washers recommended if stacking multiple terminals on the M6 posts.
NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.
Fuses are rated at 250VDC
Copper busbar for parallel our solar string fuse holders or the Tomzn DC breaker <63A in the solar combiner box to take a single feed to a charge controller for example.
10 mm², 17.5mm partition (distance between centre of poles), peg design, L-shaped bar. The busbar comes with a plastic cover. Cut the busbar down to the number of poles required for your application. Use the feeder to take a single feed from the bus bar. Made in Germany
Use the feeder terminal to take a single feed from the bus bar in the solar combiner box to a solar charge controller for example. The feeder terminal accepts from 6 - 25mm² cable and the pin length is 15mm. Consider using a ferrule or flat pin lug on the end of the cable go into the female end of the terminal. Made in Germany
25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK
Bag of 10 x 6mm Ring Yellow Crimps - 48A max current.
for 4mm or 6mm cable
10mm squared cable end lug for crimping onto 10mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK