BYD B-Box Premium LVL 15.4kWh 100% DOD Battery Module,  Lithium Iron-Phosphate battery. Cobalt Free, the successor to the B-Box 13.8

Approved for use with Victron and SMA 48 Volt battery inverters

48V lithium-ion battery storage system

- usable capacity: 15.36 kWh
- nominal voltage: 51.2 V
- Max. Output current: 250 A
- Peak output current: 375 A, 10s
- Operating Voltage Range: 40-59 V
- ambient temperature: -10 °C to +50 °C
- interfaces: CAN/RS485
- round trip energy efficiency: >= 95 %
- certification: IEC62619/ CEC / CE / UN38.3
- IP protection class: IP20
- Application: ON Grid / ON Grid + Backup / OFF Grid
- Extend anytime / up to 64 in parallel / 983 kWh usable
 

Hazardous material according to UN 3480 / Transport hazard class 9 / Packing Group II

*Please note the LVL cannot work in parallel with an exisitng B-Box 13.8 system on the same inverter*

Multifunctional
Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.

Two AC Inputs & two AC Outputs
The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source. The main output has no-break functionality. In the event of a grid failure, or shore or generator power being disconnected, the Quattro takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, such as air-conditioning or a water heater can be connected to this output.

Unique PowerAssist feature
The Quattro will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

Virtually unlimited power thanks to parallel operation
Up to 6 Quattros can operate in parallel to achieve higher power output. Three phase or split phase operation is also possible. Please check our datasheets to see which models have paralleling, three phase and split phase capabilities.

Remote Monitoring and Control
Monitor and control your Quattro and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Quattro to setting a Geofence for hire vehicles and more...

Download full datasheet

FOR LARGE PANEL DELIVERY TIMES, SCHEDULES AND COSTS - CLICK HERE

575W Super Large Wattage in a single panel! 

Dimensions 2278mm x 1134mm x 30mm (NOTE: VERY LARGE SIZE!)

CSI Solar Co., Ltd. is committed to providing high quality solar products, solar system solutions and services to customers around the world. Canadian Solar was recognized as the No. 1 module supplier for quality and performance/price ratio in the IHS Module Customer Insight Survey, and is a leading PV project developer and manufacturer of solar modules, with over 50 GW deployed around the world since 2001.

MORE POWER

Module efficiency up to 22.3 %
Up to 4.5 % lower LCOE
Up to 5.6 % lower system cost
Comprehensive LID / LeTID mitigation technology, up to 50% lower degradation
Compatible with mainstream trackers,
cost effective product for utility power plant
Better shading tolerance

Minimizes micro-crack impacts
Heavy snow load up to 5400 Pa, wind load up to 2400 Pa*

The GX Touch 50 is the display accessory for our Cerbo GX. The five inch a touch screen display gives an instant overview of your system and allows to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, its super slim waterproof design, top-mountable setup and its simple installation bring a lot of flexibility when creating a crisp and clean dashboard. 

The display comes with a 2m long HDMI and USB cable for connection to the Cerbo GX.

Download full specsheet

The Victron Cerbo is the all-new communication-centre allowing you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch 50, a MFD or our VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way.

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Fuse carriers for NH type fuses, suitable for protecting and isolating cables between the battery and inverter. Integrated handle enabling use as an isolator.

2 poles of the 3-pole carrier carrier can be used to fuse and isolate both positive and negative at the same time, all in the same device.

NH2 rated at 440VDC, 400A

95mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 430A rated for 5mins @ 100% Duty cycle

Conductor diameter 13mm, Overall diameter including sheath 18mm.

The Lynx Power In contains a positive and negative busbar with 4 connections for batteries, loads or chargers and a ground connection. It is part of the Lynx Distribution system and is available in two versions, with M8 or M10 busbar. Note that M10 refers to the busbar connection joints where the modules are connected to each other. The fuse and cable connections are always M8.

For the Lynx product that accepts the mega fuses see: https://www.bimblesolar.com/victron-lynx-distributor

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Two pole fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter. Integrated handle enabling use as an isolator.

6mm² Solar Cable - Price is per meter, simply select the quantity as the number of meters you want.

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Kraus & Naimer DC Switch

Switch - Disconnectors, 2 pole - for single string

•            IP66/67 Protection

•            Black/Grey Padlockable Handle – lockable in the OFF-position

•            Class II compliant, Grey Insulated Enclosure

•            Switch Interlocked with lid to prevent opening in “ON” position

•            Rated for use in ambient temperatures of 50°C

Plastic Enclosures, Protection IP66/67, totally insulated, M20/M25 knock-outs
Handle black, Plate Backing grey
Contact development: 2 pole, 6 contacts per circuit (2 x 3 in series)
Dimensions (w x h x d): 100mm x 178mm X 93mm

Victron MK3-USB Configuration Interface

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.

Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.

Supported Platforms

The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

STÄUBLI MC4 Solar PV connectors - Pair 

Connect your solar modules together with ease using these safe and durable genuine Staubli MC4 connectors. Snap-in lock. MC4 crimp tool required to make onto cable ends. YOUTUBE VIDEO

Manufacturer SKU
32.0016P0001-UR & 32.0017P0001-UR

See DOWNLOADS TAB for datasheet

 Technical specifications

*Please note male and female refers ot the metal conductor and not the plastic insulator*

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

One pole fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or charge controller and battery. Integrated handle enabling use as an isolator.

NH00 rated at 250VDC, 160A

Choose NH00 or NH000 fuse separately

Item dimensions 170mm H X 42mm W X 80mm D

NH2 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC

Top and bottom shroud for the 3 pole NH2 fuse disconnect. This shroud covers the bolted battery terminals at the top and bottom of the fuse disconnect assembly.

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for Pylontech C series batteries and BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

95mm squared cable end lug for crimping onto 95mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK 

95mm squared cable end lug for crimping onto 95mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK 

Premium Enhanced Cat5e UTP Patch Cables

Communications cable for use with equipment that requires ethernet RJ45 cables. This model is 2 metres long, blue in colour and the connections are booted - partially covered as per image.

• Connectors: 50 micron gold RJ45 plugs
• Cable: UL approved Cat.5 Enhanced 24AWG stranded cable
• To reduce crosstalk, short bodied connectors maintain speed & data integrity
• Moulded design suitable for advanced and new build networks

Premium Enhanced Cat5e UTP Patch Cables

Communications cable for use with equipment that requires ethernet RJ45 cables. This model is 3 metres long, blue in colour and the connections are booted - partially covered as per image.

• Connectors: 50 micron gold RJ45 plugs
• Cable: UL approved Cat.5 Enhanced 24AWG stranded cable
• To reduce crosstalk, short bodied connectors maintain speed & data integrity
• Moulded design suitable for advanced and new build networks

NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC

35mm squared cable end lug for crimping onto 35mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK