NEW 550ah c20 (460 ah c5)
2 VOLT, DEEP CYCLE WITH TUBULAR POSITIVE PLATE, 1500 CYCLE LIFE EXPECTANCY TO 80% d.o.d
198mm x 83mm x 553.5mm height, 26.7kg wet
Charge Voltage Settings
Bulk/Absorb 2.40v per cell
Float 2.23v per cell
EQ 2.47v per cell
THE NEW VFXR-SERIES
7 Features In One Device
GENERATOR MODE - CONNECT THE VFXR TO ANY GENERATOR:
1. Cover current consumption
2. Charge batteries
SUPPORT MODE- CONNECT THE VFXR TO ANY INVERTER TO EXPAND THE OUTPUT POWER:
1. Cover consumption with your inverter (any brand)
2. Cover your additional consumption with the VFXR (in cooperation with any brand)
GRID TIED MODE - INJECT EXCESSIVE POWER TO THE GRID:
3. Charge your batteries
4. Sell not consumed power to the grid
UPS MODE - USE THE BATTERIES IF THE GRID FAILS:
5. Cover consumption with the grid
6. In case of grid failure, switch to batteries without interruption
GRIDZERO MODE - USE THE GRID IF SOLAR POWER IS NOT AVAILABLE AND COVER HIGHER LOADS WITH SMALL INVERTERS:
7. Cover consumption with solar power (even with small inverters)
8. Take additional power from the grid to double the output of your inverter
MINI GRID MODE - USE THE GRID WHEN BATTERIES ARE LOW:
9. Cover consumption with solar power
10. Connect to the grid when batteries are low
BACKUP MODE - COVER GRID FAILURES WITH YOUR SOLAR SYSTEM:
11. Cover consumption with the grid
12. In grid failure, switch to solar system
The latest, most advanced features on the industry’s most trusted and proven platform—that’s the essence of OutBack’s new FXR Series of Grid/Hybrid inverter/chargers. Capable of off-grid or grid-connected operation in a single model, the FXR Grid/Hybrid inverter/chargers provide system designers with unprecedented flexibility and compatibility for nearly
any power conversion scenario.
The new FXR features and technologies on the acclaimed FX platform include:
FXR inverter/chargers can be paired with a MATE3 to add OPTICS RE to monitor and control system performance from any location. Available in power ranges from 2000W-3000W, multiple units may be stacked and connected with other OutBack Power electronics for more seamless system integration and the ability to function in a wide variety of applications, and system sizes. Up to nine inverters can be combined in a 3-phase system with the 12V, 24V or 48V models, and up to 30kW in a grid-tied 24V or 48V system. The exclusive modular system architecture means that increased power output is just an additional FXR inverter/charger away.
Available in sealed or vented units with NEMA type 1 die-cast aluminum chassis designed to operate in the harshest environmental conditions such as high temperatures, humidity or corrosive salt air, the FXR’s continue in OutBack’s tradition of absolute dependability in mission critical installations no matter how harsh or challenging the conditions.
Please Note: The new VFXR range only work with a Mate 3 (the standard Mate or Mate B will not work with them)
Info and Specs on Outback site
Excellent Nemo 2000W 48V wind turbine with built in controller
•New fresh design blades can start in breeze wind
•bull;Sleek design and aesthetics
•A power generator weighing 7.2kg and a maximum 4.5kW power output is used for the Nemo.
•Produces energy in very low wind speeds
•Quiet operation
•Wireless monitor
•Designed for long running life(15 years)
•Rated at 2.0 kW
•3 year warranty
Wind Turbine Type: Horizontal axis, up-wind
Rotor Diameter: 1776mm (69.9")
Mass: 18kg (38lbs. 8oz)
Mount Diameter: 48.6mm (1-15/16")
Number of Blades: 3
Blade Material: Carbon-fiber
Blade Mass: (per piece) 532g
B ody Material: Aluminum diecast
Product Finish: Teflon-based paint
Generator: Synchronous-type, three-phase power generator with neodymium iron boron magnets
Protection Circuit Built-in
Data Logger: Built-in
Yaw control: Free yaw (360 degrees)
Direction Control: Swing-tail
Output Control: Non-stop output control
Start-up Wind Speed: 3m/s
Cut-out Wind Speed: -
Survival Wind Speed: 49.2m/s
Rated Rotor Speed 1000rpm
Maximum Power: 2.0kW (20m/s)
Maximum Rotor Speed: 1000rpm (20m/s)
Output Voltage: DC48V
The charge voltage range: 48V to 57.2V
The float:56V
Braking System: Regenerative electromagnetic braking system
Off-grid :420Ah or more, flooded, deep cycle, marine grade batteries.
Braking System: Regenerative electromagnetic braking system
Communication System (Signal Output) Recommended system: Wireless 2-way interface remote system
Off-grid :Four-12V, 420Ah or more, flooded, deep cycle, marine grade lead-acid batteries.
275W JA Solar Panels
Bargain Price - MCS Approved
Silver frame poly JAP60S01 260-280 1000V Cypress Series
MULTICRYSTALLINE SILICON SOLAR MODULE
Key features:
Reliable quality:
Comprehensive Certificates:
Superior Warranty:
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
These are the best charge controllers on the market, they are solid, reliable and what we use for The Bimble Inn.
The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Technologies. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30% compared to non-MPPT controllers. Thanks to active cooling and intelligent thermal management cooling, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 104°F (40°C).
Included in all of the FLEXmax Charge Controllers are the revolutionary features first developed by OutBack Power, including support for a wide range of nominal battery voltages and the ability to step-down a higher voltage solar array to recharge a lower voltage battery bank. A built-in, backlit 80 character display shows the current status and logged system performance data for the last 128 days at the touch of a button. The integrated OutBack network communications allows FLEXmax series Charge Controllers to be remotely programmed and monitored via a MATE system display and provides unrivaled complete system integration.
FLEXmax MPPT Charge Controllers are the only choice when you demand a high performance, efficient and versatile charge controller for your advanced power system.
Voltage | Recommended PV Max | Absolute Max |
12V | 750W | 900W |
24V | 1500W | 1800W |
48V | 3000W | 3600W |
Click here to Download Owners Manual
FLEXmax 60 Specifications | |
---|---|
Nominal Battery Voltages | 12, 24, 36, 48, or 60 VDC (Single model - selectable via field programming at start-up) |
Maximum Output Current | 60 amps @ 104° F (40°C) with adjustable current limit |
Maximum Solar Array STC Nameplate | 12 VDC systems 900 Watts / 24 VDC systems 1800 Watts / 48 VDC systems 3600 Watts / 60 VDC Systems 4500 Watts |
NEC Recommended Solar Array STC Nameplate | 12 VDC systems 750 Watts / 24 VDC systems 1500 Watts / 48 VDC systems 3000 Watts / 60 VDC Systems 3750 Watts |
PV Open Circuit Voltage (VOC) | 150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum |
Standby Power Consumption | Less than 1 Watt typical |
Power Conversion Efficiency | 98.1% @ 60 Amps in at 48 VDC System voltage - Typical |
Charging Regulation | Five Stages: Bulk, Absorption, Float, Silent and Equalization |
Voltage Regulation Set points | 10 to 80 VDC user adjustable with password protection |
Equalization Charging | Programmable Voltage Setpoint and Duration - Automatic Termination when completed |
Battery Temperature Compensation | Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell |
Voltage Step-Down Capability | Can charge a lower voltage battery from a higher voltage PV array - Max 150 VDC input |
Programmable Auxilary Control Output | 12 VDC output signal which can be programmed for different control applications (Maximum of 0.2 amps DC) |
Status Display | 3.1" (8 cm) backlit LCD screen - 4 lines with 80 alphanumeric characters total |
Remote Display and Controller | Optional Mate or Mate2 with RS232 Serial Communications Port |
Network Cabeling | Proprietary network system using RJ 45 Modular Connectors with CAT 5e Cable (8 wires) |
Data Logging | Last 128 days of Operation - Amp Hours, Watt Hours, Time in Float , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for each day along with total Accumulated Amp Hours, and kW Hours of production |
Hydro Turbine Applications | Consult factory for approved Turbines |
Positive Ground Applications | Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can not be used for use in positive ground applications) |
Operating Temperature Range | Minimum -40° to maximum 60° C (Power capacity of the controller is automatically derated when operated above 40° C) |
Environmental Rating | Indoor Type 1 |
Conduit Knockouts | One 1" (35mm)on the back; One 1" (35mm) on the left side; Two 1" (35mm) on the bottom |
Warranty | Standard 5 year / Available 10 Year |
Weight - Unit | 11.65 lbs (5.3 kg) |
- Shipping | 14.55 lbs (6.4 kg) |
Dimensions - Unit | 13.5 x 5.75 x 4" (40 x 14 x 10 cm) |
- Shipping | 18 x 11 x 8" (46 x 30 x 20 cm) |
Options | Remote Temperature Sensor (RTS), HUB 4, HUB 10, MATE, MATE 2 |
Menu Languages | English & Spanish |
The new MATE3 System Display and Controller makes it easy to program and monitor a complete OutBack Power System. An intuitive and integrated system configuration wizard makes system setup and programming quick and seamless.
The ability to set unique multi-level user passwords allows the user to secure critical system settings from unintended changes, while still allowing open access to necessary functions.
The MATE3 is packed full of features to make system management simple. The easy-to-read graphical LCD display is backlit for dark operating conditions. Improved tactile buttons and a user programmable “favorite” key give you immediate access to the features you want, while an intuitive scroll wheel interface allows for easy adjustment of system setpoints. Expandable SD card memory allows you to increase data logging capacity as well as upgrade units in the field.
A built-in clock and calendar function enables timer-based programming of inverter and charger operation. All of your settings are stored in permanent memory to eliminate the need to reprogram in the event of a system shutdown or battery replacement. The MATE3 is an Internet enabled device – simply connecting to the Internet will allow full remote system.
By adding the Mate Controller you can also use the outback inverters as a off grid/grid hybrid system allowing you to use the power from your batteries primarily and switching to use the grid when your batteries are low, thus minimising your use of the grid and ensuring you get the best use of your renewable power set-up, and yet never run out of power. Or you can configure an automatic generator start from them if needed.
The HUB-4 communication manager allows the MATE to control and monitor a maximum of four OutBack products. The inverter/chargers can be operated in a stacked or independent configuration, and OutBack MPPT charge controllers can also be used on any of the four available ports of the HUB-4. Future OutBack products will also be compatible with the HUB-4. The HUB-4 manages both the inter-inverter communications and the MATE-inverter communication. The HUB-4 also can be used with the X-240 autotransformer when series stacked to allow full surge and continuous AC load capacity of each FX to be available on either of the 120 VAC output circuits. When two or more FX inverters are stacked in a parallel or series configuration, the system automatically turns off any excess slave inverters to save power and maximize conversion efficiency. This power save system is fully automatic and works with or without the MATE connected to the system One or two MATE system controllers and displays can be connected to the HUB. One Mate is allowed to program the systems while the other MATE is able to only control and display the system operation. When using a single MATE with a HUB-4, programming can be locked out by moving the MATE from the 1st MATE port to the 2nd MATE port once programming has been completed. The maximum distance from the HUB-4 to the power conversion product should be under 10 feet. OutBack includes two 3 foot long and two 6 foot long CAT5 cables standard with the HUB-4.
6mm Solar Cable - Price is per meter simply select the quantity as the number of meters you want.
Double Insulated UV protected solar cable
Max load: 50A
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
Surface Mounting Bracket for Mate 3 Controller.
Panel mounted hydraulic-magnetic type circuit breakers that can be used for DC sources, inverters or load circuits.
35mm Cable - Use for connecting Batteries to Inverter M8 - M10 (M8 one end M10 on the other end)
You will need 2 cables, 1 for Positive and 1 for Negative
If you need a longer cable please let us know.
Fixed Key Battery Isolator Switch
High quality metal body, Durable plastic handle
300AMP continuous
1,000AMP for up to 10 seconds
Measurements
Body: 67mm Diameter, 100mm length
10mm studs
10mm cable - Charge Controller to Batteries - 2 Meter with M8 Lug
You will need 2 cables per charge controler (Pos & Neg). The Lugs are on 1 end only as the charge controllers have bare wire connectors.
If you need longer please let us know
MC4 Solar PV connectors - Pair of Y Branches
Connect your solar modules together with ease using these safe and durable MC4 connectors. This pair of "Y" shape connectors (one in a male to female, female configuration, and one in a female to male, male configuration) will allow you to connect panels or strings of panels together. If you need to connect 3 panels together then it is cheaper to use 2 pairs of these than to purchase a 3 way splitter (its about 1/3 of the cost to use these)
Product information:
Current Rating: 30A
Voltage Rating: 1000V
Auto-lock design ensures the product with superior anti-impact forces
Low contact resistance
Excellent material which meets UL94-V0 fire safety standard for long-term outdoor application; outstanding anti-ageing and UV-resistance
Simple, quick and safe installation
MC4 Solar Connector - Price is per MC4 pair simply select the quantity as the number of MC4 pairs you want.
These are the standard connectors used on most solar panels.
TUV certified, brand new, water /weather proof rubber seal that can ensure excellent electrical contact for life time service.
The metal pin is made from high quality machined copper and sealed tip (compare to the cheap sheet metal pin) that can ensure excellent electrical contact for life time service.
Build in press tabs for easy disconnect, no tool is needed. 25A max load.
Wires should be crimped or soldered into the pins and care should be taken to get the correct pin into the correct connector. Once the pin is pushed into the connector it is difficult to remove without the correct tooling.
MC4 Main Technical Specification:
Maximum Current: 25A
Maximum voltage: 1000V
Contact resistance:≤5mmΩ
Maximum operating humidity: 5% -95% (No condensation)
Temperature: -40 ℃ ~ +90 ℃
Waterproof Grade: IP67
Flame class: UL94-V0
Connecting cable specifications: 2.5mm2 4mm2 6mm2
Test voltage: 6.6KV (50Hz, 1min)
Metal materials: nickel copper
Insulation material: PA12 * 1988HB
Lock mode: Self-locking
Security Level: Class ‖
Insertion force:≤50N
Withdrawal force:≥50N
MC4 Features:
Shell has a strong anti-aging, anti- UV capability; found in outdoor use under harsh environment requirements; according to different needs can be arbitrary and used in conjunction with a variety of cell junction box; all connections are using press-fit connection;