Please note the VSR in this kit is not suitable for Euro 5 or Euro 6 engines.
6v Platinum sealed AGM battery PLA-T105AGM, 220ah
Manufactured by Platinum, as an afordable model of the Trojan T105
Consumer and trade recognised brand
6 Volt (220ah @ 20hr rate - 180ah @ 5hr rate)
26 kg - 264mm length x 181mm wide x 276mm high
Terminals available as M8 stud LPT
|Capacity (C5)||185 Ah|
|Capacity (C10)||207 Ah|
|Capacity (C20)||225 Ah|
|Capacity (C100)||250 Ah|
|Height inc. terms||281 mm|
This product has Cheaper Delivery to Business addresses.
MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.
315W JA BiFacial Solar Panels - 60 cell
These panels have a glass back sheet so they absorb sun which bounces back from behind the panel. Great for low light and cloudy conditions. These are ideally suited to boats with a white roof as you can see gains of upto 26% from the reflection of light back from the white surface making the panel 391W. Any surface will work, but white gives you the best refraction of light back to the panel, or you can add aluminium solar reflective paint on the roof under the panel to get the best gain.
If using this panel with MPPT you should calculate this panel as 400W so that you do no overload the MPPT. Tracer MPPT's have current limiting so it doesn't matter if you go over the rated amps, but Outback will be damaged by too much power.
JA bifacial modules are assembled by high-performance PERCIUM cells and encapsulated by glass-glass panels, are capable of converting energy from incident lights on front and diffuse light, as well as reflected and scattered light on rear sides, which make them better reliability, superior low irradiance performance, and excellent energy generation performance. Framed structure is benefit to module packaging transportation and installation, higher tolerance for harsh environment and extreme weather conditions.
Pure sinewave output, high peak power and high efficiency. Combined high frequency and line frequency technologies ensure the best of both worlds. Models range from 150VA to 3000VA per module.
VE.Direct allows use with VE.Direct Bluetooth adaptor to control the inverter via your phone or laptop.
Ready assembled kit with a 6 + 1 metre pre-assembled heavy duty wiring harness complete with twin fuses. The kit is manufactured using 2 x midi fuse holders & 16mm2 / #6 AWG heavy duty extra flexible battery cable.
Very simple to install, does not require a connection to vehicle alternator
Fully epoxy sealed unit for years of trouble free service
Only 3 Connections to make
Power in, Power out & negative...that's it!
The idea of a "voltage sensitive relay" (VSR) or "voltage controlled relay" (VCR) as they are sometimes known, is to simplify the installation, no connection is made to the vehicles alternator .
Simply connect this relay to the towing vehicles positive battery terminal (via a fuse!) and link to the leisure battery
The relay monitors the towing vehicles battery voltage and when it reaches 13.3vdc, the relay switches on and supplies charging current to the aux. circuits. When the engine is stopped and the voltage of the vehicles main battery drops below 12.8vdc the unit switches off.
Only 3 connections are required to the unit and as such it can be fitted in next to no time .
Supplied with detailed full colour instructions.
Switch on voltage 13.7vdc
Switch off voltage 12.7vdc
Dimensions:-65 x 65 x 53mm
Relay connections:- 2 x 6mm studs for power in and out. 1 x 450mm cable for negative
Please Note: Do not use on Euro V/VI engines, or engines with smart alternators or regenerative brakes. These newer systems do not give a constant voltage and are not suitable for this split charge relay, please use this instead Programmable relay
A handy kit for your 12V wiring, an affordable solution using blade fuses
|Earth block 4 way|
|Blade fuse box 4way|
|Cable 2.5mm x 10m|
|Switches x 2|
|Spades x 4|
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 50A
Contacts: Copper.Tin plated
Degree of protection: IP67
Flame class: UL94-V0
Wire size range: 6mm2
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.
12V LED Fairy Lights - 10m string, coper wire that can be bent into any shape!
Durable and heat-resistant copper wire.
Flexible copper wire can easily string up how you want (don't bend tightly).
Can last for 50000+ hours! If one light goes out the rest remain lit!
Please Note: When installing do not trap the wires between objects that could crush the cables, and do not wrap tightly around screws or nails, this can brake the wires and then cause the lights to short out.
LED Quantity: 100LEDs
Connector: 2.1mm barrel socket
Light colour: warm white
Wire color: Copper
Modes: Steady on
12V Dual USB socket, surface mount or replace cigarette lighter socket with USB sockets.
Material: Aluminum alloy
Suitable for voltage: 6V-28v
The output voltage:12v
Battery Inter-connecting Cable - 35mm cable with M8 - M8 Lugs (M8 on both ends)
Made up to size for you for connecting your batteries together.
Cable Gland Entry Box, use to connect through external surface. Perfect for solar panel cables coming from outside to controller.
Simple DIN mount rail 10cm long for DC or AC DIN mount breakers. Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it. Quick easy and simple solution to install breakers to your solar system.
Use with our: