These Fridges and Freezers are manufactured using advanced DC pump technology. This means that they have the lowest power consumption on the market, ideal for use with your solar system,
845H x 494W x 494D mm
Brand New 110Ah Sealed Vented Lead Acid Battery
The Technology – Sterling’s high integrity valve regulated lead acid (VRLA) batteries operate as a starved electrolyte system. The electrolyte is limited to the amount that either is absorbed in the battery plates or wets the fibres in the separator. The resulting system allows gases produced during overcharge to diffuse from one plate to the other, and to be recombined back into the electrolyte.
This recombination creates a closed system, thus reducing the release of gases into the atmosphere under normal discharge conditions.
Since the electrolyte is recycled, there is no need to add water to the batteries. This reduced maintenance and leads to a longer life battery in a clean and compact container. They can be installed when flooded batteries are impractical.
|Nominal Capacity||110 Ah (20 hour rate)|
|Nominal Voltage||12 volt|
Features & Benefits
Tank formed construction allows for individual plates to be inspected prior to battery assembly, eliminating manufacturing defects. Plates are fully formed guaranteeing 100% capacity on delivery.
Sterling’s unique construction and sealing techniques ensures no electrolyte leakage from case or terminals, allowing batteries to be positioned on their side.
Excellent recovery from deep discharge.
Low self discharge – approx 3% per month.
Not restricted for air transport – complies with IATA ICAO special provision A67.
Impact resistant ABS case and cover.
Industry standard footprints for easy field replacement.
Charging: (25°C / 77°F)
Standby use: Float charging voltage 13.50V to 13.80V.
Top up charge: Product in storage (ambient temperature) requires a top up charge every 6 months. Apply constant voltage at 2.40 volts per cell, initial charging current should be set at less than 0.1 CA for 15 to 20 hours
MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.
325W JA Solar Panels Mono Percium - All Black Half Cell, 1689 X 996 X 35mm
Half Cell Advantages
Supplied with 1000mm output cables and QC4.10 connectors (connects to MC4s)
The latest in mono cell technology with passivated backside, local BSF and 4 Bus Bars from worldwide PV Cell leaders - JA Solar
First to reach >20.6% average cell efficiency in mass production
More Power Per m²
JA higher efficiency module type specially designed for UK rooftop market.
Maximise the kWp installation on the roof
Homogeneous Black Mono cells.
Black Frame for anti-glare and pleasing appearance.
Lower System Cost
Reduced installation and BOS cost
Excellent Low-light Performance
Enhanced spectral response at longer wavelength boosts low-light performance, which can produce more than 1% additional power compared with conventional module at system side.
Passed "3xMCS" TÜV SÜD Thresher Long life Accelerated Stress Tests.
Full range of PID-resistance tests
Harsh climate environment endurance tests
Full set of long-term reliability tests
Manufacturing inspected and certified by leading institutes such as PI-Berlin, Franhoeffer, Sgurr, OST and Solar-IF
100% in-house automatic manufacturing
2X 100% EL inspection ensuring defect-free production
Over 500MWp of JA Solar panels installed in the UK. 10GWp Worldwide.
Positive power tolerance: -0~+5W
Modules binned by current to improve system performance
Excellent mechanical load resistance: Certified to withstand high wind loads (2400Pa) and snow loads (5400Pa)
Use with Tracer MPPT's - for a single panel on a 12V system you can use a 30A MPPT with this panel.
This listing is for 1 panel, simply select how many you need in the quantity. There is NO MINIMIUM Order.
A handy kit for your 12V wiring, an affordable solution using blade fuses
|Earth block 4 way|
|Blade fuse box 4way|
|Cable 4mm x 10m|
|Switches x 2|
|Spades x 4|
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Class 5 flexible tinned copper conductor
Halogen-free cross-linked compound
Halogen-free cross-linked, flame retardant compound
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Set of 4 Aluminium mounting brackets for mounting solar panels on vans, boats, sheds or a wooden frame as a easy cheap solar framing system.
** Panels larger than 100w are not recommended to use these alone, as a direct fixing to a vehicle roof. We suggest a bespoke solution using bolts, some of our customers use these brackets and modify them to achieve this, others get a locally fabricated solution **
Aluminium mounting brackets;
Wood screws:St5.7 mm*30mm,
Socket Head Screw:M6*25mm,
Cable Gland Entry Box, use to connect through external surface. Perfect for solar panel cables coming from outside to controller.
Affordable DC Breaker for 35mm DIN mount. Use with our DIN Rail as an easy and affordable breaker solution.
Current Flows from top to bottom of the breaker:
For charge controller wire top pole to charge controller and bottom pole to battery.
For Inverter wire top pole to battery and bottom pole to inverter.
A small, low cost multimeter supplied with test leads, perfect to help you setup and test your solar installation.
DMM Functions: DC Current, AC/DC Voltage, Diode, Resistance
No. of Digits: 3.5
DMM Response Type: Average
Display Count: 1999
Range Selection: Manual
Voltage Measure DC Max: 500V
Voltage Measure AC Max: 500V
Current Measure DC Max: 5A
Resistance Measure Max: 2Mohm
Simple DIN mount rail 10cm long for DC or AC DIN mount breakers. Easy solution, simply screw the rail to the wall of your electrical installation and connect the breakers to it. Quick easy and simple solution to install breakers to your solar system.
Use with our: