TNE Series, TN’s most powerful products, are specially designed for deep cycle application. With numbers of national patent technologies, the cycle life reaches 400-600 cycles at 100% DOD, highly suitable for golf carts, electric wheelchairs, low-speed electric vehicles etc. Maintenance free technology reduce the complexity with water adding during use and become more and more popular in the market.

*** PLEASE NOTE THAT WE DO NOT OFFER SUPPORT FOR USING THIS INVERTER WITH PYLON LITHIUM BATTERIES, OR ANY OTHER MANAGED LITHIUM BATTERY. A FUTURE VERSION OF THE FIRMWARE AND BMS LINK MAY MAKE THE COMMUNICATION EASIER TO SET-UP, BUT UNTIL THEN, WE DO NOT RECOMMEND USING THIS INVERTER WITH MANAGED LITHIUM BATTERIES ***

***If you plan to use this unit with a generator for back-up charging, the generator must be a digital inverter type, otherwise the charging function will not work. See the manual for more details***

EPever's UPower All In One Solar - Inverter - Solar MPPT - Grid/Generator Charger

Great affordable all in one solution, easy to install, and works with just 3 panels in series.

please note - all in one units, with high frequency electronics, can and do emit electronic noise.  If close to sleeping areas, then this must be mitigated or considered - often by switching off at night or locating the unit away from the core living area. Where essential DC loads should be wired directly to the battery bank via a DC fuse board.

Specs

Model: UP3000-HM10022
Inverter: 3000W 
Solar MPPT: 100A 450VOC
Max PV: 4000W
AC charger: 80A

Battery connector lug size M8

See spec sheet on downloads tab for full specs

Product Highlights

• A new type of all-digital intelligent energy storage and management Inverter/charger
• MPPT technology, Max. tracking efficiency 99.5 %, Max. DC-DC conversion efficiency 98.5 %
• Advanced all-digital control technology for AC-DC charging modules
• SPWM technology, with high efficiency up to 95 %
• With the function of Utility & Solar charging ratio selection, and total charging current setting
• Four charging mode and two output mode
• Rich set of options
• RS485 isolated communication interface with standard Modbus protocol
• Extensive electronic protections
• Variety of accessories can be selected according to user’s requirements

WHITE BACKSHEET, BLACK FRAME

Learn more about TCL-Solar - Click above

S Class: N-type Shingled

TCL Solar's S Class range of solar panels incorporates shingled cell technology, which improves overall module performance by reducing grid-line failures and minimizing the risk of cell breakage.

This innovative design also reduces energy loss in partial shading conditions, optimizing production even in challenging environments. S Class modules are designed to offer high efficiency, increased durability, and long-term reliability, adapting to a wide variety of residential and commercial applications.

TCL-MR460DT182-58NS

Learn more about S-Class TCL-Solar Modules - Click below

About TCL SunPower Global

Backed by the global strength, financial stability, and technological leadership of the TCL Group, TCL SunPower Global is a leading player in the solar energy space. committed to delivering high-performance, reliable, and accessible solar solutions worldwide. We integrate advanced technology, vertical manufacturing, and a strong focus on sustainability to support the transition to clean energy. Positioned at the forefront of innovation, we pioneer next-generation solar technologies that empower individuals, organizations, and entire regions to shape a cleaner energy future. TCL SunPower Global brings to market two dedicated product brands: TCL Solar, focused on high-efficiency solar panels, and SunPower, offering integrated energy solutions. Together, they address the diverse needs of the global solar market, from residential rooftops to commercial installations and large-scale utility projects. Find more at sunpowerglobal.com, tclsolar.com, and on LinkedIn.

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Two pole fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter. Integrated handle enabling use as an isolator.

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 15m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

LB Series DC Switch Disconnects comply with the latest specifications for modern low voltage devices. Outstanding electrical characteristics of LB Switches with compact design, contribute to space saving installation and operational convenience. Basic construction and design of the switch makes it compact, safe and highly reliable. The switch uses polyamide glass filled material, having excellent track resistance (CTI) for Insulation to prevent flashover even in the most severe conditions. The special contact design and configuration makes the switch highly reliable to withstand high short circuit currents.

Features

• Compact and reliable
• Finger protection
• Easy installation
• Wiping contacts
• Excellent switching and high short circuit capacity

Applications

• Photovoltaic - Isolators
• Isolator
• Main Switch
• Emergency ON/OFF
• Inverter Applications
• AC / DC Changeover in Solar Pumps

Enclosure Technical

• Degree of Protection: IP66
• Switch rear mounted for easy connection
• Enclosure colour: Dark grey base and light grey cover.
• Switch mounted in ABS enclosure.
• Round padlocking device (Max.3 padlocks) to prevent the Switch from being made ON by unauthorised personnel
• Interlock Feature (Cover opens only in OFF position)
• 4 + 4 Knockouts so two strings can be wired (500V / String)
• M12 Knockouts suitable for MC4 Connectors
• Switch rated at 1500V

Comes with a really handy key for checking connections when the cover is off .

Knock outs are also screw in which is really easy

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

NH1 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC