Victron 90W Mono Solar Panel
90W power, great for smaller applications and lighting. These are 12V panels so you can use with PWM controllers to make a very cheap system.
Size: 780 x 668 x 30mm, please see the downloads tab for full specification.
This panel has pre punched mounting holes on the rear frame. The holes are on the longest end at 18cm in from each end so two holes on each long side.
• Low voltage-temperature coefficient enhances high-temperature operation.
• Exceptional low-light performance and high sensitivity to light across the entire solar spectrum.
• 25-Year limited warranty on power output and performance.
• 5-Year Limited warranty on materials and workmanship.
• Sealed, waterproof, multifunctional junction box gives high level of safety.
• High performance bypass diodes minimize the power drop caused by shade.
• Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation.
• A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems.
• Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance.
• Pre wired quick-connect system with PV-ST01 connectors.
As these are small panels we use standard couriers - delivery is cheaper.
Or you can collect for FREE from Near Brighton, East Sussex
New XTRA series - 3rd Generation MPPT
For 12V Solar System: 130W solar panel (60V for max input voltage)
For 24V Solar System: 260W solar panel (60V for max input voltage)
No Fan for silent operation, great for vans, boats or any live in spaces
With built in LCD advanced display and programming screen (XDS2)
New XTRA series has Lithium battery support (set via PC cable only)
The XTRA tracer models have a current limiting function, you can connect 1.5 times the rated power to the controller so if your on a budget you can use a smaller controller with more panels so that you get more power in winter or low light but don't risk overloading the controller in the summer. The output will be limited to the max listed above.
New EPEver (Tracer) series is EPsolar’s third generation of MPPT controller.
XTRA series are advanced maximum power point tracking (MPPT) charge controllers, for off grid photovoltaic systems, with display unit.
In order to maximise the energy harvest from PV arrays and simultaneously minimise the power loss within a wide range of operating conditions, XTRA series apply an advanced smart algorithm which results in up to 30% higher efficient charging, compared to a conventional pulse width modulation (PWM) charge controller. Xtra series controller have limit protection function on charging current &charging power, as well as auto derating power operation at high temperature; the above protection ensure the stability of system even at exceeded rated PV power and over temperature conditions.
Protection class IP32 and isolated RS485 communication port further improve the controller’s reliability under different application requirements. XTRA series controllers incorporate a self-adaptive three-stage charging algorithm based on a digital control circuit, which eeffectively prolongs the lifespan of battery and significantly improve the system performance. It also has extensive electronic protection for overcharge, over discharge, PV&battery reverse polarity and etc. to ensure the sustainability and durability of the o-grid solar system.
¹ If using Lithium battery, customer should use “PCsoftware” to set the lithium battery parameters
² Ingress of solid objects:Protected against solid objects over 2.5mm
² Ingress of liquids: Protected against falling drops of water, if the case is disposed up to 15 from vertical
Fixes without screwing holes in your roof!
Set of seven black solar panel mounting kit, including 6 brackets (4 courners and 2 sides) and cable gland. They are ideal for fixing our solar panels to any vehicle, caravan, boat, barge or even outbuildings and sheds to provide a strong, secure and aesthetically pleasing fixing method, the mounts will support the solar panel at the correct height above the surface to enable the flow of air underneath the panel and keep it cool, ensuring the solar panel functions at it's optimum. The mounts can be safely bonded to the surface removing the need to drill holes. The panel is secured by screwing or bolting it to the mounting corner, but the corner itself can be fixed with a good strong adhesive like 'Sikaflex' or 'CT1' or any polyurethane sealant to the roof. (Ensure the roof is clean and dry before attaching. If a painted roof ensure the paint is not flakey)
ABS mounts raise the panel by 25mm. Edge of panel to edge of ABS is 55mm.
We sell CT1 which is great for sticking these down, please see related products tab for different colours avaialble.
If you are fitting to a vehicle we recommend that you additionally bolt or screw the panel and mounting down as well, as the strength of these systems is only as strong as the roof type or paint on your roof!
NOTE - You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method...
Here is a good tutorial to get you started:
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Class 5 flexible tinned copper conductor
Halogen-free cross-linked compound
Halogen-free cross-linked, flame retardant compound
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
For use with our stick down panels and ABS mounting kits - also great for sealing cable holes
CT1 will successfully bond:
Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)