Victron 90W Mono Solar Panel

90W power, great for smaller applications and lighting.  These are 12V panels so you can use with PWM controllers to make a very cheap system.

Size: 780 x 668 x 30mm, please see the downloads tab for full specification.

This panel has pre punched mounting holes on the rear frame. The holes are on the longest end at 18cm in from each end so two holes on each long side.

BlueSolar Panels

• Low voltage-temperature coefficient enhances high-temperature operation.
• Exceptional low-light performance and high sensitivity to light across the entire solar spectrum.
• 25-Year limited warranty on power output and performance.
• 5-Year Limited warranty on materials and workmanship.
• Sealed, waterproof, multifunctional junction box gives high level of safety.
• High performance bypass diodes minimize the power drop caused by shade.
• Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation.
• A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems.
• Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance.
• Pre wired quick-connect system with PV-ST01 connectors. 

We have packages for both off grid solar panel systems and on grid Installations. (see other listings)

Delivery

As these are small panels we use standard couriers - delivery is cheaper.

Or you can collect for FREE from Near Brighton, East Sussex

15A MPPT with max VOC 75V Solar charge controller

A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally.

Load output
The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery.

Download full spec sheet

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Seven piece solar panel mounting kit in black ABS.

The set includes 6 brackets (4 corners and 2 sides) and cable entry gland. 

These mounts are ideal for fixing our solar panels to any vehicle, caravan, boat, barge or even outbuildings and sheds to provide a strong, secure and aesthetically pleasing fixing method.

The mounts will support the solar panel at 25mm above the surface enabling airflow underneath which keeps it cool, ensuring the solar panel functions at it's optimum.

General mounting guidance:

If using with panels equal to or under 175W, you can secure the panel by screwing or bolting it to the mounting corner.  The corner itself can be fixed with a good strong adhesive like 'Sikaflex' or 'CT1' which we sell in black white or clear.  See related products tab.  This removes the need to drill holes in your roof!  

You must ensure the roof is clean and dry before attaching.   If a painted roof ensure the paint is not flakey.

If you are using panels over 175W in size we recommend that not only do you bolt or screw the panel to the corners but additionally bolt or screw the mounting to the roof as well.

If fitting any panel to a vehicle we would recommend the belt and braces approach of bolting or screwing the panel to the mounts and additionally bolt or screw the mounts to the roof.  The strength of these systems is only as strong as the roof type or paint on your roof!

Notes:

- ABS mounts raise the panel by 25mm.  Edge of panel to edge of ABS is 55mm.

- You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method which is a good tutorial to get you started...

ABS Mounting tutorial

For use with our stick down panels and ABS mounting kits - also great for sealing cable holes

CT1 will successfully bond:

• Metals (including lead)
• Glass
• Mirrors
• Wood
• Polystyrene

Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals

• Prevents fungal growth
• UV resistant
• Excellent resistance to vibration
• Food safe - conforms to ISEGA Standards
• Works in wet or dry conditions
• Perfect for marine and boating maintenance, accident and emergency repairs
• Can be used in all salt-water environments
• Odourless
• Does not shrink
• Can be painted
• Contains no solvents
• No isocyanates
• Unique flexibility
• Environmentally compliant
• Instant repair and bonding with fibre glass and carbon fibre materials

Application
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)

Drying Time
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)