Made in the USA, designed to run from just 1 solar panel.
Sun Pumps SDS-T series pumps are low cost, high efficiency, positive displacement submersibles designed to be an economical solution for the “solar water pumping” industry. Constructed of Super Strong Ryton and Stainless Steel these pumps are extremely durable and corrosion resistant.
The design is an off-spring of the already time proved SDS-Q series pump. There are three standard models to choose from using 304 Stainless Steel housings and hard-ware. The same pumps can be special ordered 316 Stainless Steel housings and hardware for highly corrosive water.
They operate on 12 to 30 volts DC that may be supplied from a variety of independent sources including solar panels or batteries. It is the ideal way to provide water for remote homes, campsites, livestock, small farms or for many other needs beyond the power grid.
Depth Range: 230 feet (70 meters)
Flow Range: .6 - 2 GPM (2.3 - 7.6 LPM)
Max Load Current: 4.2 Amps
Max Load Power: 126 Watts
Discharge Size: 1/2" NPT or 15mm BT
Minimum Well Diameter: 4" (100mm)
DC Voltage Range: 30-Dec
Made with Sunpower E20 super high effeciency cells, and designed to be stuck down, these are great for vans, campers and boats. They are light weight at just 3.1Kg each and you can just stick to your roof even if curved with CT1 which we have here.
We can ship this panels worldwide. As they are not glass panels, so we can ship with standard couriers at affordable rates.
Solar cell: Sunpower E20 A grade Cells
Cells size (mm):125 x 125
Cells per module: 4 x 11
Module size (mm): 1460 x 540 x 3mm
Power tolerance: +/-3%
Nominal peak power(WP): 150
Nominal voltage(V): 25.52
Nominal current (A): 5.97
Open circuit voltage (Voc): 30.11
Short cirsuit current(Isc): 6.32
Cell Conversion efficiency: 22.60%
Operating temperature: -40 to +85°C
Max system voltage: 45V DC
Net Weight(kg): 3.1kg
Certification: CE, ROHS
Junction box with 900mm cable and MC4 connectors
Note: Junction box at the front of the panel
We advise wiring these panels in parallel for best performance and lifetime.
Manufacturers Warranty: 1 year repair/replacement of panel materials.
Please note: These panels are not designed to be walked on.
As theses are non-glass panels we can use standard couriers for delivery so delivery is available worldwide.
This is mains 230V cable to use for power from your inverter. HO7 is the standard hard wearing cable which is used on all festival and event sites.
Cenelec Code: H07RN-F
Temp. Rating: 85˚C Maximum Operating Temp.
Overall Diameter: 10.3mm Approx
3 Cores: Brown, Blue, Green/Yellow
Designed for upto 16 Amps AC.
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 50A
Contacts: Copper.Tin plated
Degree of protection: IP67
Flame class: UL94-V0
Wire size range: 6mm2
STÄUBLI MC4 Solar PV connectors - Pair of Y Branches
Connect your solar modules together with ease using these safe and durable MC4 connectors. This pair of "Y" shape connectors (one in a male to female, female configuration, and one in a female to male, male configuration) will allow you to connect panels or strings of panels together. If you need to connect 3 panels together then it is cheaper to use 2 pairs of these than to purchase a 3 way splitter (its about 1/3 of the cost to use these)
|Connector system||Ø 4 mm|
|Rated voltage||1500 V DC (UL)|
|Rated current||50 A|
|Rated impulse voltage||12 kV|
|Ambient temperature range||-40 °C...+75 °C (UL)|
|Upper limiting temperature||105 °C (Stäubli)|
|Degree of protection, mated unmated||IP67 IP2X|
|Overvoltage category/Pollution degree||CATIII / 2|
|Contact resistance of plug connectors||≤0.5 mΩ|
|Contact material||Copper, tin plated|
|Locking system (UL)||Locking type|
|UL recognized component, in accordance with UL 6703||E343181|