Pylon US5000-1C 4.8kWh Li-Ion Solar Battery 48V (Latest Model, excl. brackets)

A new battery in the US series from Pylontech. The US5000 is a 48V battery with incredible features to provide a competitive edge in the market. 

Please use a dimension of 4U per module when sizing a cabinet for these batteries.

Product Features

• Modular design for ease of expansion
• Higher usable capacity resulting in less battery modules installed
• Usable capacity 4 560Wh
• Parallel Capability of up to 16 units
• Allows for large installation of up to 72.96kWh with no LV Hub
• Intelligent BMS protecting battery cells
• 95% DoD with more usable capacity
• RS485 and CAN compatible
• Comes with a 5-year warranty extendable
• Long cycle life and superior performance
• Compatible with tier 1 inverter brands
   

If you want to use these batteries with Victron equipment please read this article to select the correct equipment:

https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
 

Here is the link to register your batteries and receive extended warranty:

https://en.pylontech.com.cn/service/registration

Note - there is no integrated breaker in this battery.

ENA approval for grid connection of this unit is now available

All-in-one solar power solution, 4000W inverter, 250/100 MPPT charge controller

The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.

The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.

Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.

Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
MultiPlus-II inverter/charger.
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.

GX device
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.

This service is for customers that are purchasing a Victron System and wish to have it pre-programmed for their specific needs, to make it a 'plug and play' system.

Pre-programming starts from £249 (+VAT).  Click DOWNLOADS tab for PDF further information.

Pre-programming usually has a 2 week lead time.

Please contact us for more information, if required a schematic can be produced.

The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. 

The fuse and cable connections are always M8. The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can.

It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar: https://www.bimblesolar.com/V-LYNX-PWRIN-M10

A set of battery brackets which allows vertical stacking of the Pylon US5000 battery unit. 1 set required per battery.

Power inlet for boat (shore power inlet), van, living vehicle or motorhome. 

16A. 250VAC

Solid Cast 316 Stainless Steel

Brass, Nickel plated pins

IP56 rating

This would require a hole making in the vehicle/vessel exterior as it is panel mounted (recessed)

Victron MK3-USB Configuration Interface

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.

Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.

Supported Platforms

The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.

350A Battery isolator switch,1200A for 30 secs, Up to 48 Volt, M10 cable stud with nut

**Please note: as per the image, the switch does not come with hardware to fix the switch to its mounting location, and this must be purchased separately, depending on type of installation (surface mount, panel mount, etc)**

BLUE SEA E-SERIES Battery Switch/Isolator

E-SERIES BATTERY SWITCHES

350 Ampere continuous rating.

• Tin-plated copper studs for maximum conductivity and corrosion resistance
• Studs accept 3⁄8" (M10) ring terminals
• 7⁄8" (22mm) stud length accepts multiple cable terminals
• One-piece terminal stud design never loosens over time
• Case design allows surface or rear panel mounting options
• Label with international legends
• Tactile indicator conveys knob position by feel

Regulatory

• CE marked, ISO 8846
• UL Listed - UL 1107 electric power switches
• Meets ABYC requirements
• Meets UL1500 and SAE J1171 external ignition protection requirements
• IP66 protects against powerful water jets

Mechanical Hexagonal crimp tool for 10mm² -120mm² copper tube terminal lugs. For manual crimping of terminal lugs and pin ferrules onto battery cable. 45cm long handles.

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.

The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.

NH00 rated at  250VDC, 160A,

Choose NH00 or NH000 fuses separately

Product measures 170mm H X 84mm W X 80mm D. Surface mountable.

Pylon battery cable accessory kit for use with all the different battery models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the inverter/charger.

Please check the number of cable packs you need, according to your inverter/charge specifications. Each cable pack is rated at 100A continuous, and 125A peak.

This cable pack includes the following cables:

2 x 2m long power cables (1x positive and 1x negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.

Pack of 5 x 200A Fuse for 12V, 24V and 48V systems

For use with Mega Fuse Holder and Lynx Distributor

70mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 355A rated for 5mins @ 100% Duty cycle

Conductor diameter 9.4mm, Overall diameter including sheath 16mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for Pylontech C series batteries and BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.

NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC

Essential for preparing the surface, removing contaminates and residues before sticking your flexible CIGS panel down.

Check solution on inconspicuous paint area first.

Take note of the Material Safety Data Sheet attached under the Downloads tab.

100ml bottle.

25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK