MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet, the Victron Remote Management Portal (VRM) will provide access to information on the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN(long-range wide area network) device, available optionally.
Optional SmartSolar Control Display
By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real time monitoring and set up capabilities.
VictronConnect
VictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built in, or are connected to a VE.Direct Bluetooth Smart Dongle.
| Victron Specifications | |
| Battery Voltage Auto Select | 12V / 24V / 48V Auto Select (software tool needed to select 36V) |
| Rated Charge Current | 85 A |
| Nominal P Vpower12V | 1,200 W |
| Nominal P Vpower24V | 2,400 W |
| Nominal P Vpower36V | 3,600 W |
| Nominal P Vpower48V | 4,900 W |
| Charge Voltage Absorption | 14.4V / 28.8V / 57.6V (adjustable) |
| Charge Voltage Float | 13.8V / 27.6V / 55.2V (adjustable) |
| Charge Algorithm | Multi-stage adaptive (adjustable) |
| Temperature Sensor | Optional (Smart Battery Sense) |
| Max Efficiency | 99 % |
| Self Consumption | Less than 35mA @ 12V / 20mA @ 48V |
| Max PV Open Circuit Voltage | 250 V |
| Start Up PVDC Voltage | The PV voltage must exceed Vbat + 5V for the controller to start. Thereafter the minimum PV voltage is Vbat + 1V |
| Number Of Trackers | 1 |
| Max PV Current Per Mc4 | 30 A |
| Max PV Short Circuit Current | 70 A |
| Protections | Output short-circuit,Excessive temperature,PV reverse polarity |
| Max Humidity | 95 % |
| Max Altitude | 5,000 |
| Environmental Condition | Indoor, unconditioned |
| Pollution Degree | PD3 |
| Bluetooth | 1 |
| Data Communication | Bluetooth,VE.Direct,VE.Can |
| Remote On Off Terminal | 1 |
| Programmable Relay | DPST AC rating: 240VAC / 4A, DC rating: 4A up to 35VDC, 1A up to 60VDC |
| Number Of Sync Parallel Operating Units | 25 |
| Number Of Sync Parallel Operating Units BT | 10 |
| PV Connection Terminal Type | MC4 connectors (two pairs) |
| Remote On Off Terminal Connection | Screw terminal two pole |
| Relay Terminal Connection1 | Screw terminal 3-pole |
| Colour | Blue (RAL 5012) |
| Protection Category | IP22 (connection area),IP43 (electronic components) |
| Weight | 4.5 kg |
| Height | 246 mm |
| Width | 295 mm |
| Depth | 103 mm |
| Safety | CSA C22.2,EN-IEC 62109-1,UL 1741 |
| Data Retention Period | 46 d |
| Data Stored | Battery voltage,Battery current,Battery temperature,PV voltage,PV current |
| Charge Controller | |
| Max VOC | 250 |
| Amps | 85 |
| Voltage | 12/24/48 |
| Cable Connection | |
| Type and size | 100A fuse and isolator (battery side) |
| Size mm2 | 35mm2 cable (max) |
| Manufacturer Warranty | |
| Standard Warranty: | 5 years (5 years extension to 10 years for additional 10% fee - contact us for a quote) |
| Warranty Exceptions: | Lead acid batteries 2 years Lithium batteries 3 years |
 (1)-54x54.jpg)
