The Fogstar Energy IP65-Rated 16.1kWh Battery, meticulously engineered for UK conditions, delivers a robust combination of advanced LiFePO4 battery technology, integrated safety systems, and long-term durability.

Designed for both indoor and outdoor installation, the Fogstar Energy IP65-Rated 16.1kWh Battery provides reliable performance in demanding environments. Its fully sealed construction, intelligent thermal management, and wide inverter compatibility make it a dependable solution for long-term energy storage.

This 16.1kWh solar battery boasts numerous advanced features, including:

Built-In Fire Suppression & IP65 Protection
The battery is housed in a fully sealed IP65-rated enclosure, protecting internal components against dust ingress and water jets from any direction. An automatic, built-in aerosol fire suppression system activates if internal temperatures reach critical levels, helping to suppress fire at the source with zero maintenance required.

Intelligent Heating System
The integrated heating system automatically activates when temperatures drop below 5°C, enabling safe charging at 0°C and reliable operation in ambient temperatures as low as -20°C.

Plug-and-Play Inverter Compatibility
The PACE Battery Management System (BMS) contains pre-loaded inverter protocols for Victron, Pylontech, Growatt, Sofar, Solis, and Goodwe. Inverter protocol selection can be changed directly via the LCD touchscreen without the need for software downloads.

Premium Grade A EVE Cells
The Fogstar Energy IP65-Rated 16.1kWh Battery utilises 16 MB31 Grade A EVE LiFePO4 cells, delivering an exceptional cycle life of up to 8,000 cycles at 80% DOD (95% DOD as of February 2026).

Active Balancing
Equipped with a 2A JK Active Balancer to ensure consistent cell balancing and improved long-term performance.

Scalable Energy Storage: Up to 15 batteries can be connected in parallel, allowing total system capacity to be expanded as energy requirements grow.

Enhanced Safety with DC Breaker: Each battery includes an integrated 250A DC breaker, providing critical protection by safely interrupting current in the event of a fault.

Intuitive Touchscreen Interface: The 4.3-inch TFT LCD touchscreen provides a clear and user-friendly interface for monitoring system status and selecting inverter protocols.

Energy-Efficient Sleep Mode: When not in use, the touchscreen automatically enters sleep mode to conserve energy, while allowing instant access to system information with a simple touch.

Wheels for Portability: Despite its robust construction, integrated wheels make the battery significantly easier to manoeuvre during installation or maintenance.

Simplified Installation: All batteries are supplied with M8 ring terminals and protective covers for straightforward and secure installation.

Fogstar Energy supports this battery with a 10-year warranty, reflecting confidence in its design, construction, and long-term reliability.

Technical specification

Manufacturer: Fogstar Energy
Model: FE48-16
Total Energy: 16,076.8Wh
Cell Type: EVE MB31 Grade A
Cell Assembly: 16S1P
Cycle Life: 8,000 cycles at 80% DOD (95% DOD as of February 2026)
BMS: PACE 200A
Maximum Discharge Current: 200A
Balancer: 2A JK Active Balancer
Capacity: 314Ah
Weight: 128.8kg
Dimensions: 500mm(L) × 232mm(W) × 915mm(H)
Nominal Voltage: 51.2V
Pre-loaded Inverter Protocols: Victron, Luxpower, Sunsynk, Solis and more.

NB: we have been informed by Fogstar that when using the battery with a Victron Cerbo-GX, you should use a Type B cable for canbus communication

We have also been informed that the battery will work with Sunsynk hybrid inverters if you set the inverter profile to Pylontech, Canbus BMS communication would then be via the provided yellow comms cable.

WHITE BACKSHEET, BLACK FRAME

Learn more about TCL-Solar - Click above

S Class: N-type Shingled

TCL Solar's S Class range of solar panels incorporates shingled cell technology, which improves overall module performance by reducing grid-line failures and minimizing the risk of cell breakage.

This innovative design also reduces energy loss in partial shading conditions, optimizing production even in challenging environments. S Class modules are designed to offer high efficiency, increased durability, and long-term reliability, adapting to a wide variety of residential and commercial applications.

TCL-MR460DT182-58NS

Learn more about S-Class TCL-Solar Modules - Click below

About TCL SunPower Global

Backed by the global strength, financial stability, and technological leadership of the TCL Group, TCL SunPower Global is a leading player in the solar energy space. committed to delivering high-performance, reliable, and accessible solar solutions worldwide. We integrate advanced technology, vertical manufacturing, and a strong focus on sustainability to support the transition to clean energy. Positioned at the forefront of innovation, we pioneer next-generation solar technologies that empower individuals, organizations, and entire regions to shape a cleaner energy future. TCL SunPower Global brings to market two dedicated product brands: TCL Solar, focused on high-efficiency solar panels, and SunPower, offering integrated energy solutions. Together, they address the diverse needs of the global solar market, from residential rooftops to commercial installations and large-scale utility projects. Find more at sunpowerglobal.com, tclsolar.com, and on LinkedIn.

Victrons new 48V inverter/charger

The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid.
It has all the features of the MultiPlus, plus an external current transformer option to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing (max. 32A).  It also has all the features of the MultiGrid with built-in anti-islanding and an increasingly long list of country approvals.

PowerAssist

The MultiPlus-II will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.

ESS: Energy Storage Systems

The MultiPlus-II is the key component in a Victron ESS system, providing the flexibility to combine with MPPT Solar Chargers or Grid-tie PV Inverters. For examples and more detailed information see the ESS (Energy Storage System) manual.

Uninterrupted AC power (UPS function)

In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

Remote Monitoring and Control

Monitor and control your Multi and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Multi to auto starting a back generator and more...

Download Spec Sheet

**NOTE - THIS IS NOT THE VE.CAN VERSION** IF YOU REQUIRE VE.CAN COMMUNICATION, PLEASE SEE THIS LISTING

70A MPPT with max VOC 250V - with barewire terminals (contact us for MC4 terminals)

MPPT: Ultra Fast Maximum Power Point Tracking

By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

Remote Monitoring and Control

Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN(long-range wide area network) device, available optionally.

Optional SmartSolar Control Display

By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.

VictronConnect

VictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.

Download full spec sheet

The GX Touch 50 is the display accessory for our Cerbo GX. The five inch a touch screen display gives an instant overview of your system and allows to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, its super slim waterproof design, top-mountable setup and its simple installation bring a lot of flexibility when creating a crisp and clean dashboard. 

The display comes with a 2m long HDMI and USB cable for connection to the Cerbo GX.

Download full specsheet

Latest version!

The main differences between the original version and this MK2 version are: 

• Two fully functional canbus ports, called VE.Can 1 and VE.Can 2. Instead of one VE.Can and one BMS-Can port.
• VE.Can 1 is isolated. On previous models, there was no isolated canbus port.
• RJ-45 sockets have been rotated 180 degrees, so its easier to take the cables out.
• All three USB ports are fully functional. Instead of two functional and one for power (to a GX Touch) only.
• Digital inputs can do pulse counting

The Victron Cerbo is the all-new communication-centre allowing you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch 50, a MFD or our VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way.

The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. 

The fuse and cable connections are always M8. The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can.

It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar: https://www.bimblesolar.com/V-LYNX-PWRIN-M10

300A Battery isolator switch, 900A for 30 secs, up to 48 Volt, M10 connection. Can be use on 12, 24 or 48 Volt system as long as switch current rating is not exceeded.

**Please note: as per the image, the switch does not come with hardware to fix the 2 sections together, and this must be purchased separately, depending on type of installation (surface mount, panel mount, etc)**

BLUE SEA M-SERIES SELECTOR SWITCHES

M-SERIES BATTERY SWITCHES

300 Ampere continuous rating.

• Tin-plated copper studs for maximum conductivity and corrosion resistance
• Studs accept 3⁄8" (M10) ring terminals
• 7⁄8" (22mm) stud length accepts multiple cable terminals
• One-piece terminal stud design never loosens over time
• Case design allows surface or rear panel mounting options
• Label with international legends
• Tactile indicator conveys knob position by feel

Regulatory

• CE marked, ISO 8846
• UL Listed - UL 1107 electric power switches
• Meets ABYC requirements
• Meets UL1500 and SAE J1171 external ignition protection requirements
• IP66 protects against powerful water jets

Victron MK3-USB Configuration Interface

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.

Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.

Supported Platforms

The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 15m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

The MC4-Evo 2 In-line Fuse (PV-K/ILF3) with a crimping connection guarantees a long-lasting, stable connection in comparison to conventional omega-style clips: Minimal energy loss, low heat generation. Robust housing, safety class IP68 (1 m, 1 h). Cable cross-section 6 mm².

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

Premade 6mm Solar Cable with MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 2.5m lengths MC4 to bare wire)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Pack of 5 x 200A Fuse for 12V, 24V and 48V systems

For use with Mega Fuse Holder and Lynx Distributor

DC Switch

• Modular design, DC insulation voltage 1500V, compact structure, 2-8 poles optional
• IP66 box design, switch rotation operator with three lockable positions, to prevent misoperation
• Suitable for different specifications of waterproof cable connector
• The zero line bridge with angle design makes the connection easier
• With sufficient internal space and good heat dissipation effect, the whole machine can work under -40℃-70℃ with full load
• High - speed "on - off" switching mechanism, using energy storage spring, fast switching, maximum switching time is less than 5ms
• Contact self-cleaning design, reduce the resistance and energy consumption of DC switch, extend the life of switch
• Magnetic arc extinguishing and gate arc extinguishing are used to suppress the arc effectively
• Passed IEC / EN60947-3: 2009+A1+A2, GB / T14048.3, with TUV, CE certification
• Torque settings: 1.2-1.8Nm
• Suitable for 4-6mm² cables

*Please see related products for the fork terminals that are recommended for use during installation*

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

Use this cable to connect a CAN-bus enabled battery, (not a Victron battery), to a Victron system. See your battery manual for details on which cable to use. Suitable for Fogstar batteries, amongst others.

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

The VE.Direct cable is used for comunication between Victron VE Direct devices. For example it can be used to connect a Victron battery monitor to the Victron Colour Control or to connect a Victron GlobalLink 520 to a Victron MPPT Controller that has a VE direct port.

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle

Conductor diameter 6.7mm, Overall diameter including sheath 13mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

These fuses are suitable for use with Pylontech US5000 batteries, when one cable set is used per module.

See Datasheet tab

• Complies to ISO 20934
• Cu alloy element
• Tin plated integrated heatsink
• Riveted PPA GF35 thermoplastic colour coded housing
• Colour coded housing with value in OCR font on both sides

ELECTRICAL & SPECIFICATIONS
Input Voltage 70V DC Maximum
Breaking capacity 2500A at 70VDC
Dimensions 68mm x 19mm x 10.5mm
Hole size M8
Hole centres 50.9mm
Maximum torque 12Nm ± 1 Nm
Identification Colour coded housing and value in OCR font on both sides