VRLA AGM: design life 7-10 years
VRLA GEL: design life 12 years
VRLA GEL 2 Volt cells: design life 20 years 

The AGM range has very low internal resistance making them particularly suitable for high current discharge applications such as for inverters, thrusters and winches. 

The GEL model range offers best deep cycle durability and overall longer life. The use of high purity materials and lead calcium grids ensure that for both AGM and GEL products have particularly low self-discharge so that they will not go flat during long periods without charge. Both ranges are supplied with M8 drilled, flat copper terminals ensuring best possible connection contact and eliminating the need for battery terminals. The batteries are compliant with both CE and UL specifications in ABS fireproof containers and come with Victron's 2 year world-wide warranty.

• Low voltage-temperature coefficient enhances high-temperature operation.
• Exceptional low-light performance and high sensitivity to light across the entire solar spectrum.
• 25-Year limited warranty on power output and performance.
• 5-Year Limited warranty on materials and workmanship.
• Sealed, waterproof, multifunctional junction box gives high level of safety.
• High performance bypass diodes minimize the power drop caused by shade.
• Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most stringent safety requirements for high-voltage operation.
• A sturdy, anodized aluminium frame allows modules to be easily roof-mounted with a variety of standard mounting systems.
• Highest quality, high-transmission tempered glass provides enhanced stiffness and impact resistance.
• Pre wired quick-connect system with PV-ST01 connectors.

Victron pure sinewave output, high peak power and high efficiency in a compact unit. Models range from 250VA to 1200VA with UK socket - other socket outlets available on request

These inverters allow you to power domestic equipment - requiring 230VAC - using 'leisure' or 'automotive' batteries rated at 12V

Bulit in DC fuse in all models but not replaceable in all models - see the manual for further details on which models carry the replaceable fuse.

Consider adding a battery isolator switch https://www.bimblesolar.com/300a-blue-sea-battery-isolator

VE.Direct communication port

The VE.Direct port can be connected to:

• A computer (VE.Direct to USB interface cable needed)

• Apple and Android smartphones, tablets, MacBook’s and other devices (VE.Direct Bluetooth Smart dongle needed)

Fully configurable:

• Low battery voltage alarm trip and reset levels

• Low battery voltage cut-off and restart levels

• Dynamic cut-off: load dependent cut-off level

• Output voltage 210 - 245V

• Frequency 50 Hz or 60 Hz

• ECO mode on/off and ECO mode sense level Monitoring:

• In- and output voltage, % load and alarms

Proven reliability

The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short circuit proof and protected against overheating, whether due to overload or high ambient temperature. High start-up power Needed to start loads such as power converters for LED lamps, halogen lamps or electric tools. ECO mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once in standby the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.

Remote on/off

A remote on/off switch can be connected to a two pole connector, or between battery plus and the left hand contact of the two pole connector

Spec Sheet

See the Download tab on this listing

New XTRA series - G3-BLE *NEW* Integrated Bluetooth - Maximum Panel Wattage input is 1.2x max rating below

NOTE - The MT50 display unit does not work with this model, you need the MT52 instead.

For 12V Solar System: 260W solar panel (100V for max input voltage)
For 24V Solar System: 520W solar panel (100V for max input voltage)

Introducing the XTRA-N G3/XTRA-N G3 BLE series controllers—a cutting-edge solar charge control solution. With a built-in Bluetooth module for easy mobile app parameter control, advanced MPPT algorithms for efficient energy tracking, and features like independent voltage regulation and comprehensive electronic protections, these controllers provide a reliable and durable solution for a variety of solar applications, from RVs to household systems. Upgrade your solar experience with the XTRA-N G3 series.

• High quality and low failure rate components of ST or IR to ensure the service life
• Advanced MPPT technology & ultra-fast tracking speed, tracking efficiency is up to 99.5%
• Maximum DC/DC transfer efficiency is as high as 98.5%; full load efficiency is up to 97.2%
• Advanced MPPT control algorithm to minimize the lost rate and lost time
• Accurate recognizing and tracking of multi-peaks maximum power point
• Wider MPP(maximum power point) running voltage to optimize PV utilization
• Support multi battery types including lithium batteries
• Equipped with a stable self-activation function for the lithium battery
• Set the battery voltage parameters on the LCD
• Battery temperature compensation
• Limit the charging power & charging current to no higher than the rated value
• Real-time energy statistics function
• Charging power reduction automatically for over-temperature
• Built-in Bluetooth to adjust settings through EPEVER APP
• RS485 communication interface with optional 4G or Wi-Fi modules for remote monitoring
• Setting parameters via the PC software, APP, or remote meter
• Constant voltage output function
• Comprehensive electronic protections
• Multiple load work modes
• Dustproof and waterproof design with IP33 enclosure
• Low self-consumption, lower than 10mA
• Operation at full load without charging power reduced in the working temperature range

Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.

(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black

Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link

Wire size range: 6mm2

Ideally 6mm solar cable max - for bigger units with bigger cable click here

Unit best used for housing 1 x AC RCBos, string fuse holders and fuses up to 32a as opposed to DC Din Mount breakers.

Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit.  If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.

This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.  

You will also need suitable cable entry glands - please see related products tab.

This PV mounting kit fits 30mm frame depth Solar Panels only.

Contains:

4 x 20cm mini rail
4 x 30mm end clamp

No bolts or screws supplied.  Suitable bolts or screws are for you to purchase separately, the installer should give their own guidance as to which ones to supply.

We cannot guide you on this, as no one should give you remote advice on how to mount anything, without physically being there to advise appropriately.

Applications can be:

Profile metal roofing where the ridge of each corrugation is flat
Timber frames with appropriate wood screws.
Steel frames using appropriate bolts.
Fibreglass using appropriate nuts & bolts & backing plate.
Canal boat roofs, 
DIY ground mount frames, 
Shed roofs
Static caravans
Smallholdings

Unlimited panels in a row using the optional middle clamps - click here or see the related products tab.

- One of these kits for one panel.
- Two panels - one of these kits and one middle clamp kit.
- Three panels - one of these kits and two middle clamp kits
And so on...

Additional rubber strip provides a weather seal against moisture and can help prevent galvanic reaction if mounted on steel.  Be sure to seal your bolts or screws after fitting the rail with an appropriate sealant to prevent water ingress.

Do not install on moving vehicles.

These mounts are very basic, if there is any wind loading to consider you are responsible for adding additional mounts to suit your installation.

Bimble Solar are not responsible for your installation and any ramifications as a result of using this product.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.

Affordable DC Breaker for 35mm DIN mount.  Use with our DIN Rail as an easy and affordable breaker solution.

Current Flows from top to bottom of the breaker: 
For charge controller wire top pole to charge controller and bottom pole to battery. 
For Inverter wire top pole to battery and bottom pole to inverter.