This a high specification all Victron, mobile off grid system and is able to charge from Solar, AC hook-up or DC from the alternator.
If you wish to swap out items, please see: Panel options for our panel options and Battery options for our 12V batteries.
You can make changes by adding the bundle to your basket as individual parts, once you have done this please contact us to ensure that all items are compatible before purchase.
If you click on the download tab you will see a Victron system schematic that you can pass to your electrical installer as a guide.
NB: all mobile installations are bespoke so you will need to discuss how this will be connected with your installer.
Victron range of small Lithium batteries for small off grid set-ups that want to use Lithium batteries. Ideal for light weight solutions. 70% small and 70% lighter than Lead acid batteries.
For Victron Smart Lithium batteries it is imperative that you purchase a BMS, Battery Management System, to go with these batteries. You will kill them quickly if you don’t use one. Please ask for advice if you are not sure about which BMS is best for your application.
Lithium-iron-phosphate (LiFePO4 or LFP) is the safest of the mainstream li-ion battery types. The nominal voltage of a LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery therefore consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series.
The new style MultiPlus is set to replace the earlier MultiPlus Compact range. It is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology and a high-speed AC transfer switch in a single compact enclosure.
Proven reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverter is short circuit proof and protected against overheating, whether due to overload or high ambient temperature.
PowerControl - Dealing with limited generator, shore side or grid power With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist - Boosting the capacity of shore or generator power Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery. High start-up power Needed to start high inrush loads such as power converters for LED lamps, halogen lamps or electric tools.
Search Mode When Search Mode is ‘on’, the power consumption of the inverter in no-load operation is decreased by approx. 70%. In this mode the Multi, when operating in inverter mode, is switched off in case of no load or very low load, and switches on every two seconds for a short period. If the output current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut down again.
Programmable relay By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too high, battery voltage almost too low.
This is a really unique panel, at just over 1m x 1.5m, the perfect size to cap off a boat storage locker or small road trailer
Please check out my solar camping trailer in the additional images.
FOR LARGE PANEL DELIVERY TIMES, SCHEDULES AND COSTS - CLICK HERE
The Triple Black DELTΔ SERIES 54 cell module from Perlight has proven extremely popular in the UK due to its sleek looks and diminutive size.
It is completely black with black busbars, a black back sheet and a black frame, which when installed in arrays, offers a more uniform appearance, enabling PV modules to integrate into new and existing buildings without necessarily making the array the focal point.
Not just aesthetically pleasing, the 295W Delta Black Monocrystalline module has PERC technology which essentially enables to improve light capture near the rear surface and to optimize electrons capture.
This module continues the trend from Perlight of well made, good looking products that offer outstanding value for money.
The Smart BMS 12/200 is an all-in-one Battery Management system for Victron Lithium-Iron-Phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator such as in vehicles and boats.
It combines a Current Limiter, Battery Combiner and Battery Protector in a robust and compact solution and lets you safely connect any size 12V alternator (and starter battery), loads and chargers to Smart Lithium batteries.
The Smart BMS 12/200 monitors and protects each individual battery cell within the battery (or battery bank) and will disconnect the alternator, charge sources or DC loads in case of low battery cell voltage, high battery cell voltage or over temperature.
The dedicated alternator connection provides current limiting and one-way traffic from the alternator into the battery, this so any size alternator (and starter battery) can be safely connected to the Smart Lithium battery (or battery bank) and the starter battery is protected from excessive discharge.
The BMS is equipped with Bluetooth for monitoring and configuration, a remote on/off connector, to turn the BMS (and the system) off via a remote switch and a pre-alarm contact, to give a warning signal before the BMS will disconnect the batteries from the system.
The BMS is also equipped with a remote on off connector, to turn the BMS (and the system) off via a remote switch.
MPPT: Ultra Fast Maximum Power Point Tracking
By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.
Remote Monitoring and Control
Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN(long-range wide area network) device, available optionally.
Optional SmartSolar Control Display
By adding the SmartSolar Control Display you will be able to check the status of your Charger and battery-storage at a glance. Simply plug it into the face of your MPPT charger to provide you with real-time monitoring and set-up capabilities.
VictronConnect
VictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.
The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. It is part of the Lynx Distribution system and is available in two versions, with M8 or M10 busbar. Note that M10 refers to the busbar connection joints where the modules are connected to each other. The fuse and cable connections are always M8. The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can.
*This listing is for the M8 version.*
It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar https://www.bimblesolar.com/Victron-lynx-powerin
The Digital Multi Control is used to remotely view and adjust AC input currents, and turn on and off the Multi or Quattro. It is designed to integrate cleanly with your boat, vehicle or house system control panel.
The Digital Multi Control panel (DMC) is designed to work with all Multi/Quattro. This includes stand alone, parallel and 2-3 phase configurations. Connecting the DMC to your system is simple, in most cases just connecting the DMC with an RJ45 cable is sufficient and no extra set-up handling is required.
300A Battery isolator switch, 900A for 30 secs, up to 48 Volt, M10 connection. Can be use on 12, 24 or 48 Volt system as long as switch current rating is not exceeded.
**Please note: as per the image, the switch does not come with hardware to fix the 2 sections together, and this must be purchased separately, depending on type of installation (surface mount, panel mount, etc)**
M-SERIES BATTERY SWITCHES
300 Ampere continuous rating.
Regulatory
The SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.
Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.
The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.
The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.
This unit has M10 bolts.
The set includes 6 brackets (4 corners and 2 sides) and cable entry gland.
These mounts are ideal for fixing our solar panels to any vehicle, caravan, boat, barge or even outbuildings and sheds to provide a strong, secure and aesthetically pleasing fixing method.
The mounts will support the solar panel at 25mm above the surface enabling airflow underneath which keeps it cool, ensuring the solar panel functions at it's optimum.
If using with panels equal to or under 175W, you can secure the panel by screwing or bolting it to the mounting corner. The corner itself can be fixed with a good strong adhesive like 'Sikaflex' or 'CT1' which we sell in black white or clear. See related products tab. This removes the need to drill holes in your roof!
You must ensure the roof is clean and dry before attaching. If a painted roof ensure the paint is not flakey.
If you are using panels over 175W in size we recommend that not only do you bolt or screw the panel to the corners but additionally bolt or screw the mounting to the roof as well.
If fitting any panel to a vehicle we would recommend the belt and braces approach of bolting or screwing the panel to the mounts and additionally bolt or screw the mounts to the roof. The strength of these systems is only as strong as the roof type or paint on your roof!
Notes:
- ABS mounts raise the panel by 25mm. Edge of panel to edge of ABS is 55mm.
- You need to purchase additional self tappers or bolts to fit the panel to the ABS mounts, see below for one method which is a good tutorial to get you started...
Power inlet for boat (shore power inlet), van, living vehicle or motorhome.
16A. 250VAC
Solid Cast 316 Stainless Steel
Brass, Nickel plated pins
IP56 rating
This would require a hole making in the vehicle/vessel exterior as it is panel mounted (recessed)
Victron MK3-USB Configuration Interface
The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.
Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.
Supported Platforms
The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.
35mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 225A rated for 5mins @ 100% Duty cycle
Conductor diameter 6.7mm, Overall diameter including sheath 13mm
Kraus & Naimer DC Switch
Switch - Disconnectors, 2 pole - for single string
• IP66/67 Protection
• Black/Grey Padlockable Handle – lockable in the OFF-position
• Class II compliant, Grey Insulated Enclosure
• Switch Interlocked with lid to prevent opening in “ON” position
• Rated for use in ambient temperatures of 50°C
Plastic Enclosures, Protection IP66/67, totally insulated, M20/M25 knock-outs
Handle black, Plate Backing grey
Contact development: 2 pole, 6 contacts per circuit (2 x 3 in series)
Dimensions (w x h x d): 100mm x 178mm X 93mm
For use with our stick down panels and ABS mounting kits - also great for sealing cable holes
CT1 will successfully bond:
Unique adhesion on virtually any material in most applications without the need for additional fixings. CT1 is the ultimate solution for sealing.
Excellent resistance to chemicals
Application
Apply with a standard cartridge caulking gun or pneumatic version at approximately 6 bar (108psi)
Drying Time
Skin cure 23ºC 50% R.H. 8 minutes
Non-adhering 23ºC 50% R. 25minutes
Full cure time 23ºC 50% R.H. 24hrs - 6mm (48hrs - 7/12mm)
Premade 6mm Solar Cable with Male to Female MC4 connectors, quick and easy to install.
(Please note if using as a cable run from panel to controller, you would cut in half giving you 2 x 5m lengths, MC4 to bare wire.)
Double Insulated UV protected solar cable
Max load: 70A in air
Our solar cable is ozone resistant according to BS EN 50396
UV resistant according to HD 605 S2 and is tested for durability according to EN 60216
Flexible tinned copper conductor
Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Fitted with Staubli 4-6mm MC4s - Staubli MC4 Link
Wire size range: 6mm2
Use this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models.
Note that it's not necessary to use this cable on the larger SmartSolar models, as they feature an onboard Remote On/Off terminal.
The charger will be enabled when the signal on the cable is high. The charger is disabled when the source signal is pulled low or left free floating.
Note that when using this cable, it's not possible to use the VE.Direct port for any other purpose. Such as connecting to a GX device, or for example a VE.Direct Bluetooth Smart dongle on a BlueSolar charger.
60A Fuse for 12v or 24 systems - Pack of 5 fuses
For use with Mega Fuse Holder
200A Fuse for 12v or 24 systems - Pack of 5 fuses
For use with Mega Fuse Holder
Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line
Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.
The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.
This item fits String Fuse holder
Communications cable for use with equipment that requires ethernet RJ45 cables. This model is 3 metres long, blue in colour and the connections are booted - partially covered as per image.
One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.
Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off the supply to a solar charge controller or solar inverter.
Choose fuse separately
Item dimensions 75mm H X 16mm W X 55mm D
35mm squared cable end lug for crimping onto 35mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK
35mm squared cable end lug for crimping onto 35mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK
16mm squared cable end lug for crimping onto 16mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK
Best practice would be to use this unit with no bigger than 6mm square cable and appropriately sized breakers if you are using it with glands for a water tight fit. If you are using it in an environment that is already dry and dust free the use of glands may not be necessary.
This is an empty unit, you must add the breakers you need to your cart as well, see related items tab above to see the breakers that fit.
You will also need suitable cable entry glands - please see related products tab.
Product Depth | 114 mm |
Product Height | 160 mm |
Product Type | DIN Enclosure |
Product Width | 85 mm |