Pylon US5000-1C 4.8kWh Li-Ion Solar Battery 48V (Latest Model, excl. brackets)

A new battery in the US series from Pylontech. The US5000 is a 48V battery with incredible features to provide a competitive edge in the market. 

Please use a dimension of 4U per module when sizing a cabinet for these batteries.

Product Features

• Modular design for ease of expansion
• Higher usable capacity resulting in less battery modules installed
• Usable capacity 4 560Wh
• Parallel Capability of up to 16 units
• Allows for large installation of up to 72.96kWh with no LV Hub
• Intelligent BMS protecting battery cells
• 95% DoD with more usable capacity
• RS485 and CAN compatible
• Comes with a 5-year warranty extendable
• Long cycle life and superior performance
• Compatible with tier 1 inverter brands
   

If you want to use these batteries with Victron equipment please read this article to select the correct equipment:

https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
 

Here is the link to register your batteries and receive extended warranty:

https://en.pylontech.com.cn/service/registration

Note - there is no integrated breaker in this battery.

ENA approval for grid connection of this unit is now available

All-in-one solar power solution, 4000W inverter, 250/100 MPPT charge controller

The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.

The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.

Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.

Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
MultiPlus-II inverter/charger.
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.

GX device
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.

WHITE BACKSHEET, BLACK FRAME

Learn more about TCL-Solar - Click above

S Class: N-type Shingled

TCL Solar's S Class range of solar panels incorporates shingled cell technology, which improves overall module performance by reducing grid-line failures and minimizing the risk of cell breakage.

This innovative design also reduces energy loss in partial shading conditions, optimizing production even in challenging environments. S Class modules are designed to offer high efficiency, increased durability, and long-term reliability, adapting to a wide variety of residential and commercial applications.

TCL-MR460DT182-58NS

Learn more about S-Class TCL-Solar Modules - Click below

About TCL SunPower Global

Backed by the global strength, financial stability, and technological leadership of the TCL Group, TCL SunPower Global is a leading player in the solar energy space. committed to delivering high-performance, reliable, and accessible solar solutions worldwide. We integrate advanced technology, vertical manufacturing, and a strong focus on sustainability to support the transition to clean energy. Positioned at the forefront of innovation, we pioneer next-generation solar technologies that empower individuals, organizations, and entire regions to shape a cleaner energy future. TCL SunPower Global brings to market two dedicated product brands: TCL Solar, focused on high-efficiency solar panels, and SunPower, offering integrated energy solutions. Together, they address the diverse needs of the global solar market, from residential rooftops to commercial installations and large-scale utility projects. Find more at sunpowerglobal.com, tclsolar.com, and on LinkedIn.

The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. 

The fuse and cable connections are always M8. The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can.

It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar: https://www.bimblesolar.com/V-LYNX-PWRIN-M10

6mm² Solar Cable - Price is for a 100 meter reel. If you wish to buy in lower quantity meter lengths, please see https://www.bimblesolar.com/6mmcable

Double Insulated UV protected solar cable

Max load: 70A in air

Our solar cable is ozone resistant according to BS EN 50396

UV resistant according to HD 605 S2 and is tested for durability according to EN 60216

Flexible tinned copper conductor

Conductor
Class 5 flexible tinned copper conductor
Insulation
Halogen-free cross-linked compound
Sheath
Halogen-free cross-linked, flame retardant compound
Sheath Colour
Black
Other colours available on request if bulk order

A set of battery brackets which allows vertical stacking of the Pylon US5000 battery unit. 1 set required per battery.

Victron MK3-USB Configuration Interface

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.

Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.

Supported Platforms

The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.

This outdoor rated combiner box is for safely combining larger strings of solar panels >= 3. The box comes fitted with Din rail and 10 X M20 glands with a cable outer diameter range of 5 - 10mm.

The enclosure features knock out discs so no drilling is required. Just punch out the number if gland spaces required, and fit the glands. You must select the fuse holder, fuses, bus bar, feeder terminal and extra glands if required for your system.  See related items tab above to see the breakers that fit. If fusing positive conductors only, select Din rail block to combine the negatives. It is possible to mount he box without puncturing it thus maintaining the IP waterproof rating

Outside dimensions: 182 X 180 X 111mm

Inside dimensions: 167 X 165 X 96mm

Effective Din rail length: 150mm

Number of gland knock outs: 8 X M20, 1 X M25 or M32 (top & bottom), 4 X M20, 1 X M32 or M40 (left side and right side)

Mechanical Hexagonal crimp tool for 10mm² -120mm² copper tube terminal lugs. For manual crimping of terminal lugs and pin ferrules onto battery cable. 45cm long handles.

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.

The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.

NH00 rated at  250VDC, 160A,

Choose NH00 or NH000 fuses separately

Product measures 170mm H X 84mm W X 80mm D. Surface mountable.

Pylon battery cable accessory kit for use with all the different battery models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the inverter/charger.

Please check the number of cable packs you need, according to your inverter/charge specifications. Each cable pack is rated at 100A continuous, and 125A peak.

This cable pack includes the following cables:

2 x 2m long power cables (1x positive and 1x negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.

300A Battery isolator switch, 900A for 30 secs, up to 48 Volt, M10 connection. Can be use on 12, 24 or 48 Volt system as long as switch current rating is not exceeded.

**Please note: as per the image, the switch does not come with hardware to fix the 2 sections together, and this must be purchased separately, depending on type of installation (surface mount, panel mount, etc)**

BLUE SEA M-SERIES SELECTOR SWITCHES

M-SERIES BATTERY SWITCHES

300 Ampere continuous rating.

• Tin-plated copper studs for maximum conductivity and corrosion resistance
• Studs accept 3⁄8" (M10) ring terminals
• 7⁄8" (22mm) stud length accepts multiple cable terminals
• One-piece terminal stud design never loosens over time
• Case design allows surface or rear panel mounting options
• Label with international legends
• Tactile indicator conveys knob position by feel

Regulatory

• CE marked, ISO 8846
• UL Listed - UL 1107 electric power switches
• Meets ABYC requirements
• Meets UL1500 and SAE J1171 external ignition protection requirements
• IP66 protects against powerful water jets

The crimp-free Stäubli PV connector: MC4-Evo ready

The Original MC4 product portfolio now offers a PV connector with the easy-to-use snap-in technology. This PV DC connector is quick to install as it enables crimp-free assembly without the need for special tools. The reduced complexity of the assembly process allows to save time while granting Stäubli quality.

The MC4-Evo ready is mateable with the Stäubli Original MC4 product portfolio as proved by TÜV Rheinland interoperability test with triple test severity.

CLICK HERE for instruction video from Stäubli

Safe connections: quick and easy installed

The crimp-free Original MC4-Evo ready complements the Stäubli PV DC product range of cable couplers for in-string and homerun connections. The new connector provides safe connections that are quick and easily installed for long-term reliability.

No crimping tools - Quick assembly with easy snap-in technology, Reliable connection, TÜV Rheinland certified

Product Main Features

• Crimp-free cable connection: no crimping necessary, the contact is made by an automatically closing spring clamp based on snap-in technology
• No single parts. The connectors are complete and pre-screwed: Insert the stripped PV wire, screw on the housing: done!
• Mateable with Original MC4 product portfolio

It is acceptable to hand tighten these connectors, but if you wanted to use a spanner type Staubli tool the reference is 32.6070 (MC4-MS-EVO READY) and currently you will need to source this yourself.

10mm tinned copper Solar Cable - Price is per meter simply select the quantity as the number of meters you want.

Double Insulated UV protected solar cable, 6.9mm Outer Diameter, Halogen-free cross-linked

Max load: 98A

European standard solar cable intended for the interconnection within photovoltaic systems such as solar panel arrays. Suitable for fixed installations, internal and external, within conduit or systems, but not direct burial applications. Our solar cable is ozoneresistant according to BS EN 50396, UV resistant according to HD 605 S2 and is tested for durability according to EN 60216.

70mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 355A rated for 5mins @ 100% Duty cycle

Conductor diameter 9.4mm, Overall diameter including sheath 16mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

One pole DIN rail mount fuse holder for 10 X 38 type fuses, suitable for protecting and isolating solar panel strings between the array and the charge controller input for example.

Rated to 1000VDC, 32A, accepts up to 16mm² cable. For use stand alone or for incorporation into a PV combiner Box with the 13 way bus bar and feeder terminal to take off  the supply to a solar charge controller or solar inverter.

Choose fuse separately

Item dimensions 75mm H X 16mm W X 55mm D

Pack of 5 x 200A Fuse for 12V, 24V and 48V systems

For use with Mega Fuse Holder and Lynx Distributor

70mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 355A rated for 5mins @ 100% Duty cycle

Conductor diameter 9.4mm, Overall diameter including sheath 16mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

Protect your off-grid or grid tied PV system from unexpected string faults using Mersen’s HelioProtection® fuse line

Developed specifically for the protection of PV string wiring for 1000VDC industrial rooftop and utility scale photovoltaic systems. Its robust construction makes it ideal for continuous temperature and current cycling withstand adding to system longevity. The 1000VDC rated fuse is designed for low minimum breaking capacity capabilities of 1.35 times the fuse rated current value, allows for safe circuit interruption under typical low fault current conditions produced by PV arrays.

The 10 X 38mm fuse can be used standalone with the DIN mount string fuse holder to fuse a single circuit or as a bank of fuses in a solar combiner box.

This item fits String Fuse holder

• Complies to ISO 20934
• Cu alloy element
• Tin plated integrated heatsink
• Riveted PPA GF35 thermoplastic colour coded housing
• Colour coded housing with value in OCR font on both sides

ELECTRICAL & SPECIFICATIONS
Input Voltage 70V DC Maximum
Breaking capacity 2500A at 70VDC
Dimensions 68mm x 19mm x 10.5mm
Hole size M8
Hole centres 50.9mm
Maximum torque 12Nm ± 1 Nm
Identification Colour coded housing and value in OCR font on both sides

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for Pylontech C series batteries and BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.

Din rail mountable junction block for joining conductors of like polarity. Can be use for joining/combining the negative conductors in our PV combiner boxes. M6 terminal lugs required separately. Additional M6 nuts and washers recommended if stacking multiple terminals on the M6 posts.

NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC

Copper busbar for parallel our solar string fuse holders or the Tomzn DC breaker <63A in the solar combiner box to take a single feed to a charge controller for example.

10 mm², 17.5mm partition (distance between centre of poles), peg design, L-shaped bar. The busbar comes with a plastic cover. Cut the busbar down to the number of poles required for your application. Use the feeder to take a single feed from the bus bar.  Made in Germany

Use the feeder terminal to take a single feed from the bus bar in the solar combiner box to a solar charge controller for example. The feeder terminal accepts from 6 - 25mm² cable and the pin length is 15mm. Consider using a ferrule or flat pin lug on the end of the cable go into the female end of the terminal.  Made in Germany

25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK 

Bag of 10 x 6mm Ring Yellow Crimps - 48A max current.

for 4mm or 6mm cable

10mm squared cable end lug for crimping onto 10mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK