The US3000C is an HESS solar battery system provided by Pylontech, developed with their own lithium iron phosphate cell to ensure the highest safety value and most promising life cycle. A self designed BMS protects the cell from abormal temperature, current, voltage, SoC and SoH.

The Pylontech US3000C has an incredible DoD of 95%. 

Please use a dimension of 3U per module when sizing a cabinet for these batteries.

Advantages

• Vertical industry integration ensures cycle life of 6000 cycles 
• Compact and fashionable design fits in your home environment
• Deliver up to 3.5kW* with single module (3.5kWh) - * please note this value is inverter/charger dependant, typically the maximum sustained value is 1.8kW per battery
• Modular design gives the end customers the power of choice of capacity
• Compatible with large number of Hybrid inverters
• Simple buckle fixing minimize the installation time and cost
• Provides pre-charge function to protect ESS system from surge current. 
• Up to 16 units can be stacked in parallel

You can now register the Pylon US3000C for an additional 3 years of manufacturer warranty for free. Go to Pylon Support and complete the information in the 'sign up battery' page.

The US3000C can be used to expand an existing US3000 bank. Please note, the US3000C needs to be used as the master battery when used to expand an existing US3000 bank.

Important

DIP switch has been deployed reversely. ON is down, OFF is UP. If DIP switches need to be 1000 then set it to 1110. MAX DISCHARGE AND CHARGE RATE IS ONLY APPLICABLE FOR +- 60 SECONDS

If using this battery with Victron equipment it requires a Type A communications cable to the Victron GX device not a Type B.

You can optionally add mounting brackets BRACK-US3000 to this product for a stable base, and to allow easy stacking of multiple units.
 

If you want to use these batteries with Victron equipment please read this article to select the correct equipment:

https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom

Here is the link to register your batteries and receive extended warranty:

https://en.pylontech.com.cn/service/registration

ENA approval for grid connection of this unit is now available

All-in-one solar power solution, 4000W inverter, 250/100 MPPT charge controller

The EasySolar-II GX combines a MPPT Solar Charge Controller, an inverter/charger and control hub in one enclosure. The product is easy to install, with a minimum of wiring.

The all-in-one solar power solution
The Victron EasySolar-II GX integrates the following elements:
• A MultiPlus-II inverter/charger
• A SmartSolar MPPT -Tr solar charge controller
• A GX device with a 2 x 16 character display.
These elements come prewired together inside a single unit. This greatly simplifies
most installations, saving time and money.

Display and wifi
The display reads battery, inverter and solar charge controller parameters.
The same parameters can be accessed with a smartphone or other wifi enabled device.
In addition, wifi can be used to set up the system and to change settings.

Solar charge controller
The DC output of the SmartSolar MPPT is parallel wired with the DC connection of the
MultiPlus-II inverter/charger.
The on/off mechanism of the MultiPlus-II also controls the SmartSolar MPPT.

GX device
The integrated GX device includes:
• A VE.Can interface. This can be used to connect to Victron VE.Can devices (e.g.
VE.Can MPPTs), or the port can be reconfigured via the Remote Console for use
with a compatible CAN-bus Li-ion Battery
• A USB port
• A Ethernet port
• A VE.Direct port
The GX device controls the MultiPlus-II and the SmartSolar MPPT with respectively a
VE.Bus and a VE.Direct connection.

A set of battery brackets which allows vertical stacking of the Pylon US3000 battery unit. 1 set required per battery.

The Lynx Distributor contains a positive and a negative busbar. The positive busbar has four fuse-protected connections with fuse monitoring. The negative busbar has four connections and a ground connection. 

The fuse and cable connections are always M8. The Lynx Distributor has a power LED and four fuse status indication LEDs. If connected to a Lynx Smart BMS, up to 4 Lynx Distributors can send fuse status information to the Lynx Smart BMS. This feature is not available when connected to a Lynx Shunt VE.Can.

It will monitor the status of each fuse and indicate its condition with a LED if used in conjunction with Lynx Shunt VE Can. The Lynx Distributor is part of the modular Lynx distribution system. See here for the Lynx Power In bus bar: https://www.bimblesolar.com/V-LYNX-PWRIN-M10

The Victron VM-3P75CT energy meter is a standard device to measure the power and energy of single- and three-phase applications, for example, at the distribution box or to measure the output of a PV Inverter, AC Genset or the output of an inverter and inverter/charger.

The meter is supplied with CT clamps which have an internal diameter of 10mm. Please ensure your meter tails are able to pass through the clamps, or make provisions for downsizing the tails appropriately.

Victron MK3-USB Configuration Interface

The MK3-USB allows the following products to connect to a computer for configuration and firmware updates using the Victron VE Configure software

Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and other Inverters with a VE.Bus communication port.

Counsider purchasing a Cat 5 ethernet cable to go with this product if you don't already have one. You won't be able to connect the MK3 interface to an inverter product without an ethernet cable.

Supported Platforms

The VEConfigure tools are only available for Windows. For Mac, there is a (not officially supported) work around available.

350A Battery isolator switch,1200A for 30 secs, Up to 48 Volt, M10 cable stud with nut

**Please note: as per the image, the switch does not come with hardware to fix the switch to its mounting location, and this must be purchased separately, depending on type of installation (surface mount, panel mount, etc)**

BLUE SEA E-SERIES Battery Switch/Isolator

E-SERIES BATTERY SWITCHES

350 Ampere continuous rating.

• Tin-plated copper studs for maximum conductivity and corrosion resistance
• Studs accept 3⁄8" (M10) ring terminals
• 7⁄8" (22mm) stud length accepts multiple cable terminals
• One-piece terminal stud design never loosens over time
• Case design allows surface or rear panel mounting options
• Label with international legends
• Tactile indicator conveys knob position by feel

Regulatory

• CE marked, ISO 8846
• UL Listed - UL 1107 electric power switches
• Meets ABYC requirements
• Meets UL1500 and SAE J1171 external ignition protection requirements
• IP66 protects against powerful water jets

**Please note: these fuse holders are designed to be opened in a specific way (see attached diagram in downloads section for guidance). Failure to follow the correct method will result in damage to the fuse holder, which is not covered by warranty.**

Fuse holder for NH type fuses, suitable for protecting and isolating cables between the battery and inverter or PV charge controller and the battery. Integrated handle enabling use as an isolator.

The 2 pole holder can be used to fuse and isolate both positive and negative at the same time, all in the same device or the positive conductor from two charge controllers for example.

NH00 rated at  250VDC, 160A,

Choose NH00 or NH000 fuses separately

Product measures 170mm H X 84mm W X 80mm D. Surface mountable.

Pylon battery cable accessory kit for use with all the different battery models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the inverter/charger.

Please check the number of cable packs you need, according to your inverter/charge specifications. Each cable pack is rated at 100A continuous, and 125A peak.

This cable pack includes the following cables:

2 x 2m long power cables (1x positive and 1x negative) The cables are 25mm² and have an M8 eyelet on one end of each cable.

70mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 355A rated for 5mins @ 100% Duty cycle

Conductor diameter 9.4mm, Overall diameter including sheath 16mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

Pack of 5 x 200A Fuse for 12V, 24V and 48V systems

For use with Mega Fuse Holder and Lynx Distributor

70mm² cable per meter, Class 6 multi-stranded extra flexible tinned copper conductor, 355A rated for 5mins @ 100% Duty cycle

Conductor diameter 9.4mm, Overall diameter including sheath 16mm

Why Orange?  Why no Red & Black options...

We only sell loose orange weld cable which is better than the red or black alternatives. It's top quality tinned copper cable, you need to accept the colour of the sheath or heat shrink over it. The benefits of tinned copper is better conductivity and much great corrosion resistance for marine and mobile applications.

In addition, our battery cables are manufactured in accordance with BS 638 Part 4 & EN 50525-2-81. It has a rubber compound to achieve the 85deg temp rating to meet all the requirements of EM5, that allows the cable to achieve the increased current carrying capacity.

Inferior cable has PVC instead of rubber and can only achieve a 70deg temp rating, which suggest a reduced current carrying capacity and inability to meet EM5 standards.

Premium Enhanced Cat5e UTP Patch Cables

Communications cable for use with equipment that requires ethernet RJ45 cables. This model is 5 metres long, blue in colour and the connections are booted - partially covered as per image.

• Connectors: 50 micron gold RJ45 plugs
• Cable: UL approved Cat.5 Enhanced 24AWG stranded cable
• To reduce crosstalk, short bodied connectors maintain speed & data integrity
• Moulded design suitable for advanced and new build networks

Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. Types A - normally for Pylontech C series batteries and BYD battery applications. Please review the battery manual for details on which cable to use for which brand/model of battery.

NH00 high capacity fuses suitable for protection of cables from batteries to inverters or charge controllers.

Fuses are rated at 250VDC

25mm squared cable end lug for crimping onto 25mm² multi-stranded battery cable. Heavy duty lug with flared cable entry. Tin plated copper. Made in the UK